AJA FR1 Operating instructions

www.aja.com
Installation and Operation
Guide
Because it matters.
FR1 and FR2
Video Card Frames
(Models FR1, FR1-D, FR2 and FR2-D)
Published: 7/13/10

2
Trademarks
AJA, Io, and Kona are trademarks of AJA Video,Inc. All other trademarks are the property of their
respective holders.
Notice
Copyright © 2010 AJA Video,Inc. All rights reserved.All information in this manual is subject to
change without notice.No part of the document may be reproduced or transmitted in any form, or by
any means,electronic or mechanical, including photocopying or recording, without the express
written permission of AJA Inc.
Contacting Support
To contact AJA Video for sales or support, use any of the following methods:
180 Litton Drive, Grass Valley, CA. 95945 USA
Telephone: [phone] or +1.530.274.2048
Fax: [phone]
Web: http://www.aja.com
Support Email: suppor[email protected]
Sales Email: [email protected]
When calling for support, have all information on the product (serial number etc.) at hand prior to
calling.
Limited Warranty
AJA Video warrants that this product will be free from defects in materials and workmanship for a period of five
years from the date of purchase. If a product proves to be defective during this warranty period,AJA Video, at its
option, will either repair the defective product without charge for parts and labor, or will provide a replacement in
exchange for the defective product.
In order to obtain service under this warranty, you the Customer, must notify AJA Video of the defect before the
expiration of the warranty period and make suitable arrangements for the performance of service.The Customer
shall be responsible for packaging and shipping the defective product to a designated service center nominated
by AJA Video, with shipping charges prepaid.AJA Video shall pay for the return of the product to the Customer if
the shipment is to a location within the country in which the AJA Video service center is located.Customer shall be
responsible for paying all shipping charges, insurance, duties, taxes,and any other charges for products returned
to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care.AJA Video shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than AJA Video representatives to install, repair or service the product,
b) to repair damage resulting from improper use or connection to incompatible equipment, c) to repair any
damage or malfunction caused by the use of non-AJA Video parts or supplies, or d) to service a product that has
been modified or integrated with other products when the effect of such a modification or integration increases
the time or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY AJA VIDEO IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED.AJA VIDEO
AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. AJA VIDEO’S RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE WHOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES IRRESPECTIVE OF WHETHER AJA VIDEO OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF
SUCH DAMAGES.
Important Safety Information
See the Safety & Regulatory information in Appendix A at the back of this manual.

1
3
AJA FR1 and FR2 Video Card Frames User Manual
Introduction
The AJA FR1 and FR2 are multiple-card frames that support both AJA’s R-series
video card modules and other industry standard modules.They bring high-
density packaging, high capacity power supplies, and forced fan cooling to
your rack—so you don’t need to reserve space above or below the frames.
Model FR1
The FR1 frame offers space for four modules in a 1-RU space. AJA’s own R5 and
R20 modules fit into the frame, as well as industry standard modules. Color
black reference can be connected at a rear panel BNC for distribution passively
to all frame modules.
Model FR2
The FR2 frame provides greater space,housing up to ten modules in a 2-RU
space.Like the FR1, the FR2 supports both AJA’s own R-series modules as well
as industry standard modules.Color black reference in the FR2 is also
distributed to all modules, but it’s actively distributed rather than passively.
Optional redundant power supplies are available for the FR2 frame, and all
power supplies are easily hot-swapped from the front of the unit (one screw on
the rear panel must be removed on each power supply prior to removal).
Features
The FR1 and FR2 frames offer a variety of unique features for easy connectivity
and ease of installation in any environment.
FR1 and FR2 Frames
FR1 Features
• Dual fan forced-air cooling
• Optional redundant power supply, diode isolated
• Universal power supply is auto-ranging from 90 to 240 VAC with 50 Watts
capacity
• 4 module slots (cells)
• Each module cell is provided with 9 BNC inputs or outputs
• Single frame reference BNC distributes passively to all cells
• Remote power supply monitoring via RJ45 port on rear panel
• Power LEDs on front panel show power status
• Compatible with common industry frames—video cards only (Leitch™
6800-series)

4
FR2 Features
• Triple fan forced-air cooling inside removable access door
• Hot-swappable power supplies
• Optional redundant power supplies, diode isolated
• Universal power supply is auto-ranging from 90 to 240 VAC with 100 Watts
capacity
• 10 module slots (cells)
• Each module cell is provided with 9 BNC inputs or outputs
• Single frame reference BNC distributes actively to all cells via an internal
distribution amplifier
• Remote power supply monitoring via RJ45 port on rear panel
• Power LEDs on front panel show power status
• Compatible with common industry frames—video cards only (Leitch™
6800-series)
I/O Connections
FR1 Multiple Card Frame, Rear Panel Connectors

1
5
AJA FR1 and FR2 Video Card Frames User Manual
FR2 Multiple Card Frame, Rear Panel Connectors
Input/Output BNCs (groups of 9 per cell) — Each unique slot in the FR1/FR2
frames connect to a group of 9 BNCs on the frame rear panel. The actual
function of the BNC connectors is dependent on the video card installed.
Each group of 9 BNCs corresponds to the card installed in the same position;
for example the right-most card connects to the right-most group of
connectors at the position on the rear panel.
Frame Reference BNC — Both the FR1 and FR2 frames have this frame reference
input BNC connector, which feeds an external reference video signal to all
modules installed in the frame. How the signal is distributed differs for the
FR1 and FR2 frames. Additionally, individual modules can usually be strapped
as to whether external reference is distributed from the frame or directly to
BNCs on the module’s corresponding cell group (the 9 BNCs on the rear
panel). See the “Note” below for more information on looping reference
inputs in the cell group.
FR1 Frame: the external reference signal is distributed passively to all frame
modules. Cards installed in the frame should have “FRAME” reference
selected, and one and only one card in the frame should have
“TERMINATION” set to “ON.” All other cards in the frame should have
TERMINATION set to “OFF.”
FR2 Frame: the external reference signal is distributed by an in-frame
distribution amplifier to all frame modules. This system terminates the Frame
Reference input BNC and buffers the signal to all slots. Cards installed in the
FR2 frame should have “FRAME” set for reference select, and all cards should
have TERMINATION set to “OFF.”

6
Note:
Each cell group of 9 BNCs contain two BNCs that can be used for a looping
reference connection for the corresponding card module.If this method is used,then
the reference select setting on that module should be set to“LOOP”and the
TERMINATION setting on the module should be set to“OFF”(no termination).
Optionally, if you’re using only one of the looping reference BNCs, then the
TERMINATION setting should be set to“ON.”
Power Supply Monitoring RJ45 Port —Standard RJ45 10BaseT-style
connector offers access for monitoring power supply voltages (see pinout
at back of manual) from the power supply (or supplies in the case of the
FR2).
AC Power Connectors —The FR1/FR2 have one AC power connection socket;
the FR1-D/FR2-D have two—one for each of their power supplies (these
models offer redundant power supplies).
User Controls
Power LEDs (2) — The PS1 and PS2 LEDs on the
FR1/FR2 front door indicate which (if any) power
supply is currently powered up and supplying
power to the frame modules. You can tell at a
glance if a supply is powered up and functional by
its associated LED.
Note:
If the front door is removed while power is applied,the fans in the front door
and the power monitoring LEDs will not operate until the door is replaced.
Installation
Typically, installation consists of the following:
1. disconnect power from the frame (remove line cord)
2. remove the FR1/FR2 front panel
3. install AJA R-series or other industry-standard card modules
4. apply external color black reference at the frame’s External Reference BNC
5. replace the FR1/FR2 front panel door
6. apply power to the frame by connecting a north american-style power cord
from the frame to mains power (90 to 260 VAC)
Please follow all manufacturer’s instructions for the video cards being installed,
noting any cautions or special instructions.
Instructions for removing the front door for module installation and power supply
exchange/removal (FR2 only) are provided in the following discussions.

1
7
AJA FR1 and FR2 Video Card Frames User Manual
Front Door
Removal/
Installation
To remove the front door,firmly grasp both removal knobs and rotate them in opposite
directions. Hang on to the knobs so that as the door releases you can hold on to the
door and remove it without it falling off.
Caution!
The FR1/FR2 front fan door is heavy and is not hinged.Remove with Caution.
Power Supply
Removal (FR2)
To remove an FR2 power supply, follow these steps:
Warning!
Ensure Mains Power is disconnected before installing the FR1 or FR2 frame R-series
modules into the frame, or installing and removing options.If a Mains switch is not
provided, the power cord(s) of this equipment provide the means of disconnection.
The socket outlet must be installed near the equipment and must be easily
accessible.
Warning!
FR2 Dual Power Cord Notice—please read this.To reduce the risk of electrical shock,
disconnect both power cords before servicing equipment.
1. Remove the frame front panel door as explained earlier.
2. Locate which of the two supplies you wish to remove.On the rear panel, remove
the strain relief screw that secures the power supply to the frame, saving the
screw.
3. From the front of the frame,grasp the two pull handles on the front of the
desired power supply and gently pull it out of the frame.
Installation of a new supply is the reverse of this removal procedure.
FR2 Power Supply Removal
Remove screw
from desired supply
Grasp Supply By
Its Handle and Pull
Out
Rear of FR2 Panel
Front of FR2 Panel
(Door Removed)

8
Note:
FR1 power supply replacement requires disassembly of the chassis frame.It
is not user-serviceable; power supply replacement should be referred to a qualified
AJA service center.
Warning!
Disconnect the external AC power supply line cord(s) from the mains power
before moving the unit.
Specifications
FR1 Specifications
FR2 Specifications
Item Specification
Capacity 4 slots, 1 Rack Unit
Inputs • Group of 9 BNCs (I/O) for each module (4 groups)
• Reference Input BNC
Power 50 Watt Capacity
Universal Input 90-240 VAC Power Supply
Optional Redundant Power Supply, Diode-Isolated
Cooling Dual fan, forced-air
Physical Dimensions Width: 19”
Height: 1.75”
Depth: 14.75”
Rack Units: 1
Compatibility Leitch™ 6800-series
Options FR1-PS Power Supply Module for FR1 Frame
Models FR1—FR1 frame with one power supply
FR1-D—FR1 frame with two (redundant) power supplies
Item Specification
Capacity 10 slots, 2 Rack Units
Inputs • Group of 9 BNCs (I/O) for each module (10 groups)
• Reference Input BNC, active DA to all slots
Power 100 Watt Capacity
Universal Input 90-240 VAC Power Supply
Optional Redundant Power Supply, Diode-Isolated
Cooling 3-fan, forced-air

1
9
AJA FR1 and FR2 Video Card Frames User Manual
FR1/FR2 Power
Monitoring
The power supply outputs can be monitored via the RJ45 connector on the rear panel.
The following diagram shows the pinouts where supply values can be measured.
Pinout for RJ45 Connector On Rear Panel
Physical Dimensions Width: 19”
Height: 3.5”
Depth: 13”
Rack Units: 2
Compatibility Leitch™ 6800-series
Options FR2-PS Power Supply Module for FR2 Frame
Models FR2—FR2 frame with one FR2-PS power supply
FR2-D—FR2 frame with dual power supplies
FR2-PS—FR2 Power supply
Item Specification
1
2
3
4
5
6
7
8
-6.5 Volts PS2
-6.5 Volts PS1
Ground
Serial Com Port
Serial Com Port
Ground
+6.5 Volts PS2
+6.5 Volts PS1
RJ45 Connector on Rear Panel
Description
Pin Numbers

10
Federal Communications Commission (FCC) Compliance Notices
Class A
Interference
Statement
This equipment has been tested and found to comply with the limits for a Class A digital
device,pursuant to Part 15, Subpart B of the FCC Rules.These limits are designed to provide
reasonable protection against harmful interference in a commercial installation.This
equipment generates, uses, and can radiate radio frequency energy and,if not installed and
used in accordance with the instructions,may cause harmful interference to radio
communications.However, there is no guarantee that interference will not occur in a
particular installation. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his
own expense.If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Canadian ICES Statement
Canadian Department of Communications Radio Interference Regulations
This digital apparatus does not exceed the Class A limits for radio-noise emissions from a
digital apparatus as set out in the Radio Interference Regulations of the Canadian Department
of Communications.This Class A digital apparatus complies with Canadian ICES-003.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique respecte les limites de bruits radioélectriques visant les appareils
numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du
ministère des Communications du Canada. Cet appareil numérique de la Classe A est
conforme à la norme NMB-003 du Canada.
Appendix A: Safety & Compliance

1
11
AJA FR1 and FR2 Video Card Frames User Manual
European Union and European Free Trade Association (EFTA)
Regulatory Compliance
This equipment may be operated in the countries that comprise the member countries of the
European Union and the European Free Trade Association.These countries, listed in the
following paragraph, are referred to as The European Community throughout this document:
AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA, FINLAND,
FRANCE, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LATVIA, LITHUANIA, LUXEMBOURG,
MALTA, NETHERLANDS, POLAND, PORTUGAL, ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN,
UNITED KINGDOM, ICELAND, LICHTENSTEIN, NORWAY, SWITZERLAND
Declaration of
Conformity
Marking by this symbol indicates compliance with the Essential Requirements of the EMC
Directive of the European Union 2004/108/EC.
This equipment meets the following conformance standards:
Safety:
CB- IEC 60065:2001 + A1:2005
NRTL - UL 60065:2003 R11.06, CSA C22.2 NO.60065:2003 + A1:06
GS - EN 60065:2002 + A1
Additional licenses issued for specific countries available on request.
Emissions:
EN 55103-1: 1996
EN61000-3-2:2006, EN61000-3-3:1995 +A1:2001 +A2:2005
Immunity:
EN 55103-2: 1996
EN61000-4-2:1995 + A1:1999 + A2:2001, EN61000-4-3:2006, EN61000-4-4:2004,
EN 61000-4-5: 2005, EN 610004-6:2007, EN61000-4-11:2004
The product is also licensed for additional country specific standards as required for
the International Marketplace.
Warning!
This is a Class A product. In a domestic environment,this product may cause
radio interference,in which case, the user may be required to take appropriate
measures.
Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können
bei Betrieb dieses Gerätes Rundfunkstörungen auftreten,in welchen Fällen der Benutzer für
entsprechende Gegenmaßnahmen verantwortlich ist.
Attention! Ceci est un produit de Classe A.Dans un environnement domestique,ce produit
risque de créer des interférences radioélectriques, il appartiendra alors à l’utilisateur de
prendre les mesures spécifiques appropriées.

12
Korea KCC Compliance Statement
Taiwan Compliance Statement
This is a Class A product based on the standard of the Bureau of Standards, Metrology and
Inspection (BSMI) CNS 13438, Class A.
Japanese Compliance Statement
This is a Class A product based on the standard of the VCCI Council (VCCI V-3/2008.04). If this
equipment is used in a domestic environment, radio interference may occur, in which case,
the user may be required to take corrective actions.
Translated caution statements, warning conventions and warning messages
The following caution statements,warning conventions, and warning messages apply to this
product and manual.
1. Class A ITE
この装置は、クラスA 情報技術装置です。この装置を家庭環境で使用すると電波妨害
を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求され
ることがあります。ＶＣＣＩ−Ａ
Warning Symbol Hazard Warning Caution Symbol

1
13
AJA FR1 and FR2 Video Card Frames User Manual
Before operating your unit, please read the instructions in this document
Warning!
Read and follow all warning notices and instructions marked on the product or
included in the documentation.
Avertissement ! Lisez et conformez-vous à tous les avis et instructions
d'avertissement indiqués sur le produit ou dans la documentation.
Warnung! Lesen und befolgen Sie die Warnhinweise und Anweisungen, die auf dem Produkt
angebracht oder in der Dokumentation enthalten sind.
¡Advertencia! Lea y siga todas las instrucciones y advertencias marcadas en el producto o
incluidas en la documentación.
Aviso! Leia e siga todos os avisos e instruções assinalados no produto ou incluídos na
documentação.
Avviso! Leggere e seguire tutti gli avvisi e le istruzioni presenti sul prodotto o inclusi nella
documentazione.
Warning!
Do not use this device near water and clean only with a dry cloth.
Avertissement! N'utilisez pas cet appareil près de l'eau et nettoyez-le seulement
avec un tissu sec..
Warnung! Das Gerät nicht in der Nähe von Wasser verwenden und nur mit einem trockenen
Tuch säubern.
¡Advertencia! No utilice este dispositivo cerca del agua y límpielo solamente con un paño seco.
Aviso! Não utilize este dispositivo perto da água e limpe-o somente com um pano seco.
Avviso! Non utilizzare questo dispositivo vicino all'acqua e pulirlo soltanto con un panno
asciutto.
Warning!
Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Avertissement ! Ne bloquez aucune ouverture de ventilation. Suivez les instructions du
fabricant lors de l'installation.
Warnung! Die Lüftungsöffnungen dürfen nicht blockiert werden. Nur gemäß den
Anweisungen des Herstellers installieren.
¡Advertencia! No bloquee ninguna de las aberturas de la ventilación. Instale de acuerdo con las
instrucciones del fabricante.
Aviso! Não obstrua nenhuma das aberturas de ventilação.Instale de acordo com as instruções
do fabricante.
Avviso! Non ostruire le aperture di ventilazione.Installare in conformità con le istruzioni del
fornitore.
Warning!
Do not install near any heat sources such as radiators, heat registers,stoves, or other
apparatus (including amplifiers) that produce heat.
Avertissement ! N'installez pas l'appareil près d'une source de chaleur telle que des radiateurs,
des bouches d'air de chauffage,des fourneaux ou d'autres appareils (amplificateurs compris)
qui produisent de la chaleur.
Warnung! Nicht in der Nähe von Wärmequellen wie Heizkörpern, Heizregistern, Öfen oder
anderen Wärme erzeugenden Geräten (einschließlich Verstärkern) aufstellen.

14
¡Advertencia! No instale cerca de fuentes de calor tales como radiadores, registros de calor,
estufas u otros aparatos (incluidos amplificadores) que generan calor.
Aviso! Não instale perto de nenhuma fonte de calor tal como radiadores, saídas de calor,
fogões ou outros aparelhos (incluindo amplificadores) que produzam calor.
Avviso! Non installare vicino a fonti di calore come termosifoni, diffusori di aria calda, stufe o
altri apparecchi (amplificatori compresi) che emettono calore.
Warning!
Refer all servicing to qualified service personnel. Servicing is required when the
device has been damaged in any wav, such as power-supply cord or plug is
damaged,liquid has been spilled or objects have fallen into the device,the device
has been exposed to rain or moisture, does not operate normally, or has been
dropped.
Avertissement ! Référez-vous au personnel de service qualifié pour tout entretien.L'entretien
est exigé quand l'appareil a été endommagé de quelque manière que ce soit,par exemple
lorsque le cordon d'alimentation ou la prise sont endommagés, que du liquide a été versé ou
des objets sont tombés dans l'appareil, que l'appareil a été exposé à la pluie ou à l'humidité,
ne fonctionne pas normalement ou est tombé.
Warnung! Das Gerät sollte nur von qualifizierten Fachkräften gewartet werden.Eine Wartung
ist fällig,wenn das Gerät in irgendeiner Weise beschädigt wurde, wie bei beschädigtem
Netzkabel oder Netzstecker, falls Flüssigkeiten oder Objekte in das Gerät gelangen, das Gerät
Regen oder Feuchtigkeit ausgesetzt wurde, nicht ordnungsgemäß funktioniert oder fallen
gelassen wurde.
¡Advertencia! Consulte al personal calificado por cuestiones de reparación.El servicio de
reparación se requiere cuando el dispositivo ha recibido cualquier tipo de daño,por ejemplo
cable o espigas dañadas,se ha derramado líquido o se han caído objetos dentro del
dispositivo, el dispositivo ha sido expuesto a la lluvia o humedad, o no funciona de modo
normal, o se ha caído.
Aviso! Remeta todos os serviços de manutenção para o pessoal de assistência qualificado. A
prestação de serviços de manutenção é exigida quando o dispositivo foi danificado mediante
qualquer forma, como um cabo de alimentação ou ficha que se encontra danificado/a,
quando foi derramado líquido ou caíram objectos sobre o dispositivo, quando o dispositivo
foi exposto à chuva ou à humidade, quando não funciona normalmente ou quando foi
deixado cair.
Avviso! Fare riferimento al personale qualificato per tutti gli interventi di assistenza.
L'assistenza è necessaria quando il dispositivo è stato danneggiato in qualche modo, ad
esempio se il cavo di alimentazione o la spina sono danneggiati,è stato rovesciato del liquido
è stato rovesciato o qualche oggetto è caduto nel dispositivo, il dispositivo è stato esposto a
pioggia o umidità, non funziona correttamente o è caduto.
Caution!
This device is a Class A product. Operation of this equipment in a residential area
is likely to cause harmful interference,in which case users will be required to take
whatever measures may be necessary to correct the interference at their own
expense.
Attention! Le périphérique est un produit de Classe A.Le fonctionnement de cet équipement
dans une zone résidentielle risque de causer des interférences nuisibles, auquel cas
l'utilisateur devra y remédier à ses propres frais.
Achtung! Dies ist ein Gerät der Klasse A. Bei Einsatz des Geräts in Wohngebieten kann es
Störungen des Radio- und Fernsehempfangs verursachen. In diesem Fall muss der Benutzer
alle notwendigen Maßnahmen ergreifen, die möglicherweise nötig sind, um die Störungen
auf eigene Rechnung zu beheben.
¡Precaución! Este es un producto clase A. El uso de este equipo en áreas residenciales puede
causar interferencias nocivas,en cuyo caso,se requerirá que los usuarios tomen cualquier
medida necesaria para corregir la interferencia por cuenta propia.

1
15
AJA FR1 and FR2 Video Card Frames User Manual
Cuidado! Este dispositivo é um produto Classe A.Operar este equipamento em uma área
residencial provavelmente causará interferência prejudicial; neste caso,espera-se que os
usuários tomem as medidas necessárias para corrigir a interferência por sua própria conta.
Attenzione! Questo dispositivo è un prodotto di Classe A. Il funzionamento di questo
apparecchio in aree residenziali potrebbe causare interferenze dannose, nel cui caso agli utenti
verrà richiesto di adottare tutte le misure necessarie per porre rimedio alle interferenze a
proprie spese.
Warning!
Disconnect the external AC power supply line cord(s) from the mains power before
moving the unit.
Avertissement ! Retirez le ou les cordons d’alimentation en CA de la source
d’alimentation principale lorsque vous déplacez l’appareil.
Warnung! Trennen Sie die Wechselstrom-Versorgungskabel vom Netzstrom,bevor Sie das
Gerät verschieben.
¡Advertencia! Cuando mueva la unidad desenchufe de la red eléctrica el/los cable(s) de la
fuente de alimentación CA tipo brick.
Advertência! Remova os cabos CA de alimentação brick da rede elétrica ao mover a unidade.
Avvertenza! Scollegare il cavo dell’alimentatore quando si sposta l’unità.
Hazard Warning!
High Voltage.This situation or condition can cause injury due to electric shock.
Avertissement ! Tension élevée.Cette situation ou condition peut causer des
blessures dues à un choc électrique.
Warnung! Hochspannung.Diese Situation oder Bedingung kann zu Verletzungen durch
Stromschlag führen.
¡Advertencia! Alto voltaje . Esta situación o condición puede causar lesiones debidas a una
descarga eléctrica.
Aviso! Alta Tensão . Esta situação ou condição pode causar danos devido a choques elétricos.
Avviso! Alta tensione.Questa situazione o condizione può causare lesioni a causa di scosse
elettriche.
Warning!
Only use attachments and accessories specified and/or sold by the manufacturer.
Avertissement ! Utilisez seulement les attaches et accessoires spécifiés et/ou
vendus par le fabricant.
Warnung! Verwenden Sie nur Zusatzgeräte und Zubehör angegeben und / oder verkauft
wurde durch den Hersteller.
¡Advertencia! Utilice solamente los accesorios y conexiones especificados y/o vendidos por el
fabricante.
Aviso! Utilize apenas equipamentos/acessórios especificados e/ou vendidos pelo fabricante.
Avviso! Utilizzare soltanto i collegamenti e gli accessori specificati e/o venduti dal produttore.
Warning!
Ensure Mains Power is disconnected before installing the FR1 or FR2 frame R-series
modules into the frame, or installing and removing options.If a Mains switch is not
provided, the power cord(s) of this equipment provide the means of disconnection.
The socket outlet must be installed near the equipment and must be easily
accessible.

16
Avertissement ! S’assurer que la source principale d’alimentation est débranchée avant
d’installer les modules des cartes série R de boîtier FR1 ou FR2 sur l’appareil, ou avant
d’installer ou de supprimer des options. Si aucun commutateur principal n’est fourni, le ou les
cordons d’alimentation de cet équipement fournissent le moyen nécessaire pour le
débranchement. La prise doit être installée près de l’équipement et doit être facilement
accessible.
Warnung! Vor der Installation der FR1 oder FR2 Steckkartenmodule der R-Serie in den
Rahmen bzw. vor der Installation oder dem Entfernen von Optionen muss sichergestellt
werden,dass der Netzstrom ausgeschaltet bzw. abgetrennt ist.Wenn kein Netzschalter
verfügbar ist, kann der Netzstrom mithilfe des/der Netzkabel(s) am Gerät getrennt werden.
Die Steckdose muss in der Nähe des Geräts installiert und leicht zugänglich sein.
¡Advertencia! Asegúrese de que la energía de la red de electricidad esté desconectada antes
de instalar el módulo de tarjeta de cuadro FR1 o FR2 serie R dentro del cuadro, o antes de
instalar o desinstalar opciones.Si el interruptor de la red eléctrica no se encuentra disponible,
desconecte el/los cable(s) eléctrico(s) del equipo.La toma de corriente debe ser instalada
cerca del equipo y debe estar fácilmente accesible.
Advertência! Certifique-se de que a alimentação principal esteja desconectada antes de
instalar os cartões R-series FR1 ou FR2 no quadro ou ao instalar e desinstalar opcionais.Se não
houver um interruptor de alimentação principal,o próprio cabo de alimentação do
equipamento é o meio de desconexão. A tomada de alimentação deve ser instalada próxima
ao equipamento e seu acesso deve ser fácil.
Avvertenza! Verificare che la rete di alimentazione sia scollegata prima di installare i moduli
FR1 o FR2 serie R nel telaio, o installare o rimuovere le opzioni.Se non è disponibile un
interruttore di alimentazione, il/i cavo/i di alimentazione di questa apparecchiatura
forniscono i mezzi di sconnessione. La presa deve essere installata vicino all'apparecchio e
deve essere facilmente accessibile.
Warning!
FR2 Dual Power Cord Notice—please read this.To reduce the risk of electrical
shock, disconnect both power cords before servicing equipment.
Avertissement ! Notice relative aux doubles cordons d’alimentation de
FR2—veuillez lire. Pour réduire le risque de choc électrique, débranchez
les deux cordons d’alimentation avec d’effectuer tout entretien de l’équipement.
Warnung! Hinweis zum FR2 mit doppeltem Netzkabel – bitte beachten. Um das
Risiko eines Elektroschocks zu verringern, sind beide Netzkabel vor der Wartung des
Geräts abzutrennen.
¡Advertencia! Aviso: Cable eléctrico FR2 dual — Por favor leer. Para reducir el riesgo
de electrocución, desconecte ambos cables eléctricos antes de reparar el equipo.
Advertência! Aviso do cabo duplo de alimentação FR2 — leia isto. Para reduzir o risco de
choque elétrico, desconecte ambos os cabos de alimentação antes de qualquer manutenção
no equipamento.
Avvertenza! Avviso cavo a doppia potenza FR2.Per ridurre il rischio di scosse elettriche,
scollegare entrambi i cavi di alimentazione prima di effettuare qualsiasi operazione di
manutenzione.
Warning!
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong.The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.

1
17
AJA FR1 and FR2 Video Card Frames User Manual
Avertissement ! La sécurité de la prise polarisée ou de la prise de type mise à la terre ne doit en
aucun cas être empêchée de fonctionner. Une prise polarisée a deux broches,l'une étant plus
large que l'autre. Une prise de type mise à la terre a deux broches et une troisième broche pour
la mise à la terre.La broche large ou la troisième broche sont fournies pour votre sécurité.Si la
prise fournie ne s'insère pas dans votre prise femelle,consultez un électricien pour le
remplacement de la prise femelle obsolète.
Warnung! Der Sicherheitszweck des gepolten bzw. Schukosteckers ist zu berücksichtigen. Ein
gepolter Stecker verfügt über zwei Pole, von denen einer breiter als der andere ist. Ein
Schukostecker verfügt neben den zwei Polen noch über einen dritten Pol zur Erdung.Der breite
Pol bzw. der Erdungspol dienen der Sicherheit.Wenn der zur Verfügung gestellte Stecker nicht
in Ihren Anschluss passt, konsultieren Sie einen Elektriker, um den veralteten Anschluss zu
ersetzen.
¡Advertencia! No eche por tierra la finalidad del tipo de enchufe polarizado con conexión a
tierra. Un enchufe polarizado tiene dos espigas,una más ancha que la otra. Un enchufe con
conexión a tierra tiene dos espigas iguales y una tercera espiga que sirve para la conexión a
tierra. La expiga ancha, o la tercera espiga, sirven para su seguridad. Si el enchufe suministrado
no encaja en el tomacorriente, consulte con un electricista para reemplazar el tomacorriente
obsoleto.
Aviso! Não anule a finalidade da segurança da ficha polarizada ou do tipo ligação terra.Uma
ficha polarizada tem duas lâminas sendo uma mais larga do que a outra.Uma ficha do tipo de
ligação à terra tem duas lâminas e um terceiro terminal de ligação à terra. A lâmina larga ou o
terceiro terminal são fornecidos para sua segurança. Se a ficha fornecida não couber na sua
tomada, consulte um electricista para a substituição da tomada obsoleta.
Avviso! Non compromettere la sicurezza della spina polarizzata o con messa a terra. Una spina
polarizzata ha due spinotti,di cui uno più largo.Una spina con messa a terra ha due spinotti e un
terzo polo per la messa a terra.Lo spinotto largo o il terzo polo sono forniti per motivi di
sicurezza.Se la spina fornita non si inserisce nella presa di corrente, contattare un elettricista per
la sostituzione della presa obsoleta.
Warning!
Since the Mains plug is used as the disconnection for the device,it must remain
readily accessible and operable.
Avertissement ! Puisque la prise principale est utilisée pour débrancher l'appareil,elle doit
rester aisément accessible et fonctionnelle.
Warnung! Da der Netzstecker als Trennvorrichtung dient,muss er stets zugänglich und
funktionsfähig sein.
¡Advertencia! Puesto que el enchufe de la red eléctrica se utiliza como dispositivo de
desconexión, debe seguir siendo fácilmente accesible y operable.
Aviso! Dado que a ficha principal é utilizada como a desconexão para o dispositivo, esta deve
manter-se prontamente acessível e funcional.
Avviso! Poiché il cavo di alimentazione viene usato come dispositivo di sconnessione, deve
rimane prontamente accessibile e operabile.
Warning!
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles,and the point where they exit from the device.
Avertissement ! Protégez le cordon d'alimentation pour que l'on ne marche pas dessus ou
qu'on le pince,en particulier au niveau des prises mâles,des réceptacles de convenance,et à
l'endroit où il sort de l'appareil.
Warnung! Es muss verhindert werden, auf das Netzanschlusskabel zu treten oder dieses zu
knicken, besonders an den Steckern, den Steckerbuchsen und an dem Punkt,an dem das Kabel
aus dem Gerät heraustritt.
¡Advertencia! Puesto que el enchufe de la red eléctrica se utiliza como dispositivo de
desconexión, debe seguir siendo fácilmente accesible y operable.

18
Aviso! Proteja o cabo de alimentação de ser pisado ou de ser comprimido particularmente
nas fichas,em tomadas de parede de conveniência e no ponto de onde sai do dispositivo.
Avviso! Proteggere il cavo di alimentazione in modo che nessuno ci cammini sopra e che non
venga schiacciato soprattutto in corrispondenza delle spine e del punto in cui esce dal
dispositivo.
Warning!
Unplug this device during lightning storms or when unused for long periods of
time.
Avertissement ! Débranchez cet appareil pendant les orages avec éclairsou s'il est inutilisé
pendant de longues périodes.
Warnung! Das Gerät ist bei Gewitterstürmen oder wenn es über lange Zeiträume ungenutzt
bleibt vom Netz zu trennen.
¡Advertencia! Desenchufe este dispositivo durante tormentas eléctricas o cuando no se lo
utilice por largos periodos del tiempo.
Aviso! Desconecte este dispositivo da tomada durante trovoadas ou quando não é utilizado
durante longos períodos de tempo.
Avviso! Utilizzare soltanto i collegamenti e gli accessori specificati e/o venduti dal produttore,
quali il treppiedi e l'esoscheletro.
Caution!
The FR1/FR2 front fan door is heavy and is not hinged.Remove with Caution.
Attention ! La porte frontale du ventilateur de FR1/FR2 est lourde et ne
repose pas sur des charnières.Retirer avec précaution.
Achtung! Die vordere Gebläsetür des FR1/FR2 ist schwer und lässt sich nicht
klappen. Bitte vorsichtig entfernen.
¡Precaución! La puerta del ventilador delantero del FR1/FR2 es pesada y no posee
bisagras. Extraer con precaución.
Atenção! A porta frontal de acesso aos ventiladores do FR1/FR2 é pesada e não
possui dobradiças. Remova com cuidado.
Attenzione! La porta anteriore della ventola FR1/FR2 è pesante e non è a cerniera.
Rimuovere con cautela.