Alibi Security Vigilant ALI-XS50-UVA User manual

IP Camera Quick Guide
Read the safety notice and important tips in the
included manuals before using your camera
Introduction
1
Accesing the IPC & Log in
2
Live Video
3
Default IP address is 192.168.1.30
1
Default ID : admin
Password : admin
2
Live
Setup
Event
3
Stream selection(Main / Sub)
Speaker On / Off
MIC. On / Off
Stream
disconnection
Screen Capture
Full Screen
File path
1
Record
Zoom Control
Focus Control
One time Auto Focus
Stream Connection
(Option)
(Option)
This is a megapixel network camera which uses a Progressive
Scan Exmor CMOS Sensor.
Built-in triple codec(H.264, MPEG4 and MJPEG) and streaming server,
the advantage of this camera allow you to monitor real time image from
a remote location via internet.
This camera supports both static IP and Dynamic IP and it also supports
latestes Onvif.
Alibi Vigilant
Specialty IP Camera
Quickstart Guide
This is a network camera which uses a Sony STARVIS CMOS Sensor from Exmor
Built-in triple codec(H.264, H.265, and MJPEG) and streaming server,
the advantage of this camera allow you to monitor real time image from
a remote location via internet.
This camera supports both static IP and Dynamic IP and it also supports
latest Onvif.
Caution
Software, server and service may be changer accordin gto policy or may be stopper without prior notication.
Appearance, function, and specication may be changes without prior notication. Ou rcompany assumes no
responsibility for visible or invisible loss resulted from changes in policy or products.
Safety Cautions
1.) This camera may be damaged by electrical and physical shock.
2.) Use regulated 12V DC power supply.
3.) In case of unit failure DO NOT try to disassemble the product. Contact Alibi Tech support at 888-858-1442
for troubleshooting.
4.) All resposibility by using this unit is on the owner.
5.) In case of installation in high location, be sure to mount securely to prevent the unit from falling below.
If the product is to be put out of operation indenitely, take it to a local recycling plant for proper disposal.
Please read the instructions carefully for correct use of the camera and preserve it for future reference. This
specication is subject to change without prior notice to improve the quality.
IP Camera Quick Guide
Read the safety notice and important tips in the
included manuals before using your camera
Introduction
1
Accesing the IPC & Log in
2
Live Video
3
Default IP address is 192.168.1.30
1
Default ID : admin
Password : admin
2
Live
Setup
Event
3
Stream selection(Main / Sub)
Speaker On / Off
MIC. On / Off
Stream
disconnection
Screen Capture
Full Screen
File path
1
Record
Zoom Control
Focus Control
One time Auto Focus
Stream Connection
(Option)
(Option)
This is a megapixel network camera which uses a Progressive
Scan Exmor CMOS Sensor.
Built-in triple codec(H.264, MPEG4 and MJPEG) and streaming server,
the advantage of this camera allow you to monitor real time image from
a remote location via internet.
This camera supports both static IP and Dynamic IP and it also supports
latestes Onvif.
IP Camera Quick Guide
Read the safety notice and important tips in the
included manuals before using your camera
Introduction
1
Accesing the IPC & Log in
2
Live Video
3
Default IP address is 192.168.1.30
1
Default ID : admin
Password : admin
2
Live
Setup
Event
3
Stream selection(Main / Sub)
Speaker On / Off
MIC. On / Off
Stream
disconnection
Screen Capture
Full Screen
File path
1
Record
Zoom Control
Focus Control
One time Auto Focus
Stream Connection
(Option)
(Option)
This is a megapixel network camera which uses a Progressive
Scan Exmor CMOS Sensor.
Built-in triple codec(H.264, MPEG4 and MJPEG) and streaming server,
the advantage of this camera allow you to monitor real time image from
a remote location via internet.
This camera supports both static IP and Dynamic IP and it also supports
latestes Onvif.
Installation
1
4
5
Setup - Video setting
Setup - Network setting
6 7
Event - Alarm and MotionSetup - System
Stream selection
Video settings for streams
RTSP address
This Network camera supports triple streams simultaneously
Update F/W
Factory set & Reset
Update configuration file
Expert all parameters for device and
user defined scripts
Alarm In / Out Setting
Motion detection Setting
Port Change
IP address Change
Use DHCP(Dynamic Host Configuration Protocol)
(Default IP Address is 192.168.1.30)

Alibi Vigilant Recorder Note:
These IPC will not Plug and Play with Vigilant NVRs. In order to plug IPC into
back of NVR you must set up the camera to match the NVRs internal NIC
address (i.e. 172.16.0.XXX), then plug into NVR.
To attach IPC to back of NVR:
1.) Plug IPC into POE switch or regular switch with a 12v power supply
attached to camera.
2.) Log into camera via default IP address (192.168.1.30) through web
browser.
3.) Go to Setup -> Basic Conguration -> Network
4.) Change IP address to match internal NIC scheme of NVR, match the subnet
mask (255.255.0.0 is default), set the default gateway.
5.) Click Save at the bottom.
6.) Unplug IPC from switch and plug into desired channel on back of NVR
7.) Log into NVR and go to Menu -> Camera
8.) Within the row of the channel you’d like to add camera, click on the Cam
Cong icon
9.) Change Add Mode to IP Address, Protocol to ONVIF, IP address of IPC,
HTTP Port (default 80), username, password.
10.) Click OK.
Notes:
Vigilant NVR will not nd the IPC on network via Auto Search option.
Motion detection is supported, however the motion detection eld needs to
be set up within the IPC web GUI (Section 6 of instructions). The NVR will not
allow you to edit the motion detection eld or sensitivity with in the NVR ->
Menu -> Alarm -> Motion settings.
Installation
1
4
5
Setup - Video settingSetup - Network setting
6 7
Event - Alarm and MotionSetup - System
Stream selection
Video settings for streams
RTSP address
This Network camera supports triple streams simultaneously
Update F/W
Factory set & Reset
Update configuration file
Expert all parameters for device and
user defined scripts
Alarm In / Out Setting
Motion detection Setting
Port Change
IP address Change
Use DHCP(Dynamic Host Configuration Protocol)
(Default IP Address is 192.168.1.30)
Installation
1
4 5
Setup - Video settingSetup - Network setting
6
7
Event - Alarm and Motion
Setup - System
Stream selection
Video settings for streams
RTSP address
This Network camera supports triple streams simultaneously
Update F/W
Factory set & Reset
Update configuration file
Expert all parameters for device and
user defined scripts
Alarm In / Out Setting
Motion detection Setting
Port Change
IP address Change
Use DHCP(Dynamic Host Configuration Protocol)
(Default IP Address is 192.168.1.30)
Installation
1
4 5
Setup - Video settingSetup - Network setting
6
7
Event - Alarm and MotionSetup - System
Stream selection
Video settings for streams
RTSP address
This Network camera supports triple streams simultaneously
Update F/W
Factory set & Reset
Update configuration file
Expert all parameters for device and
user defined scripts
Alarm In / Out Setting
Motion detection Setting
Port Change
IP address Change
Use DHCP(Dynamic Host Configuration Protocol)
(Default IP Address is 192.168.1.30)