Alphatron Marine AlphaFeverCamera User manual

AlphaFeverCamera
Network Turret Camera
alphatronmarine.com

AlphaFeverCamera Quick Start Guide
ii
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmfulinterference.
2. This device must accept any interference received, including interference that may
cause undesiredoperation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the EMC Directive 2014/30/EU, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot
be disposed of as unsorted municipal waste in the European Union. See the
product documentation for specific battery information. The battery is
marked with this symbol, which may in clude lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

AlphaFeverCamera Quick Start Guide
iii
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings Follow these safeguards to
prevent serious injury or death.
Cautions Follow these precautions to prevent
potential injury or material damage.
Warnings
The device should be used in compliance with local laws and electrical safety
regulations. Refer to the appropriate documentation for detailed information.
The input voltage should conform to IEC60950-1 standard: SELV (Safety Extra Low
Voltage) and the Limited Power Source (12 VDC). Refer to the appropriate
documentation for detailed information.
DO NOT connect multiple devices to one power adapter, to avoid over-heating or fire
hazards caused byoverload.
Make sure the plug is properly connected to the power socket.
If smoke, odor, or noise arises from the device, immediately turn off thepower,
unplug the power cable, and contact the servicecenter.
The installer and user are responsible for password and security configuration and its
settings.
Both internal and external grounds should be connected properly. (The crosssection
area of the grounding wire must be no less than 4 mm2, and no less than that of the
phase connector).
Cautions
Do not drop the device or subject it to physical shock.
Wipe the device gently with a clean cloth and a small quantity of ethanol, if
necessary.
Do not aim the lens at the sunor any other bright light.

AlphaFeverCamera Quick Start Guide
iv
When any laser equipment is in use, make sure that the device lens is not exposed to
the laser beam, or it may burnout.
⚫Do not place the camera in extremely hot, cold (the working temperature shall be -
40 °C to 65 °C), dusty or damp locations, and do not expose it to high electromagnetic
radiation.
Place the device in a dry and well-ventilated environment.
Keep non-waterproof devices away from liquids.
Keep the device in original or similar packaging while transportingit.
A few device components (e.g., electrolytic capacitor) require regular replacement.
The average lifespan varies, so periodic checking is recommended. Contact your
dealer fordetails.
Improper use or replacement of the battery may result in explosion hazard. Replace
with the same or equivalent type only. Dispose of used batteries in conformance with
the instructions provided by the batterymanufacturer.
Never attempt to disassemble thedevice.

AlphaFeverCamera Quick Start Guide
v
Table of Contents
1 Preparation............................................................................................... 1
2 Appearance Description............................................................................ 2
2.1 Type I Turret Camera Appearance ........................................................................ 2
2.2 Type II Turret Camera Appearance ....................................................................... 2
2.3 Cable Descriptions................................................................................................ 3
2.4 Alarm In/Out Connections.................................................................................... 3
3 Install the Turret Camera........................................................................... 4
3.1 Monitor Distance Range....................................................................................... 4
3.2 Install Memory Card ............................................................................................. 5
3.3 Install Turret Camera ............................................................................................ 5
3.4 Install Network Cable Water-proof Jacket............................................................ 8
3.4.1 Install Network Cable Waterproof Jacket ...................................................... 8
3.4.2 Waterproof Other Cables ............................................................................... 9
4 Set the System over the LAN ................................................................... 10
4.1 Wiring................................................................................................................. 10
4.2 Activate the System............................................................................................ 10
4.2.1 Activation via Web Browser ......................................................................... 10
4.2.2 Activation via SADP Software....................................................................... 11
4.3 Modify the IP Address ........................................................................................ 12
5 Operate via Web browser ....................................................................... 14
5.1 Access the System.....................................................................................................14
5.2 Live View Page.................................................................................................... 15
6 Appendix................................................................................................. 17
6.1 Common Material Emissivity Reference............................................................. 17
6.2 Frequently Asked Questions (FAQ)..........................................................................18
6.2.1 Device Running Error ................................................................................... 18
6.2.2 Device Upgrading......................................................................................... 18
6.2.3 Others .......................................................................................................... 18

AlphaFeverCamera Quick Start Guide
1
1Preparation
Basic Requirement
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Check the package contents and make sure that the device in the package is in
good condition and all the assembly parts areincluded.
Use the system according to the working environment requirement.
Check Installing Environment
Be sure that there is enough space to install the Turret Camera and accessories.
Make sure that the wall is strong enough to withstand at least 8 times the weight
of the system and themount.
Prepare Cables
According to the actual network bandwidth, the Cat5 (in 100M) or Cat6 (100M
above) isneeded.
⚫When the Turret Camera uses standard 12V DC power supply, the power cable
should be American wire gauge 18 or above. The formula of the cross-section S
(mm²) and the maximum transmission distance L (m) of the bare wire is L=50*S.
⚫Choose the video cable according to the transmission length. The video should
meet the least demands as: 75Ω resistance; 100% copper core conducting wire;
95% weaving coppershield.
Prepare Tools
Before installation, please prepare the tools needed, such as the expansion screws,
electric hammer, electric drill, wrench, screwdriver, electroprobe and network
cable.
Original Packaging
When you unpack the Turret Camera, please keep the original package properly, in
case of returning or repairing the Turret Camera, you can pack the Turret Camera
with the package.
Note: The user should be responsible for any damage caused when transporting
with unoriginal package.

AlphaFeverCamera Quick Start Guide
2
2Appearance Description
There are two types of thermal network turret cameras. Here are the overviews of Type
I camera and Type IIcamera.
2.1 Type I Turret Camera Appearance
Refer to the following figure for type I thermal turret camera overview.
Figure 2-1 Type I Thermal Turret Camera Overview
2.2 Type II Turret Camera Appearance
Refer to the following figure for type II thermal turret camera overview.
Figure 2-2 Type II Thermal Turret Camera Overview

AlphaFeverCamera Quick Start Guide
3
OUT(n)
+
DC
OUT(n)
-
Thermal Speed
Dome
Relay Output
2.3 Cable Descriptions
The cable interfaces of Turret Camera are shown in the figure below. The cables of
RS-485, power supply, alarm inputs, alarm outputs, etc. are distinguished by different
colors. Please refer to the labels attached on the cables for identification.
Audio Output Interface
Audio Input Interface
Alarm Interface
RS-485 Interface
Power Interface
Network Interface
Figure 2-3 Cables of Thermal Turret Camera
2.4 Alarm In/Out Connections
This section is only for the Turret Camera with alarm in/out functions.
The Turret Camera can be connected with alarm inputs (0~5VDC) and alarm outputs.
Refer to the following diagrams for alarm output:
DC Load
Diagram (left) Diagram (right)
Figure 2-4 Alarm Out Connections
The alarm provides the relay output (no voltage), and the external power supply is
required when it connects to the alarm device.
For DC power supply (left diagram), the input voltage must be no more than 30VDC,
1A.
For AC power supply, the external relay must be used (right diagram) to prevent
damages to the Turret Camera and avoid risk of electric shock.
Thermal speed
Dome
Relay Output
GND OUT
30VDC
1A
JQC-3FG
Relay
(10A 250VAC)
～ 220V AC
OUT(n)
L
N
OUT(n)

AlphaFeverCamera Quick Start Guide
4
3Install the Turret Camera
Before you start:
1. Check the package contents and make sure that the device in the package is in good
condition and all the assembly parts are included.
2. Please turn off the power of the Turret Camera before connecting the cables.
Notes:
⚫Do not drag the Turret Camera with its waterproof cables, or the waterproof
performance isaffected.
⚫Please remove the protective film on the Turret after the installation.
⚫Do not touch the bubble of the lower Turret directly. The image blurs otherwise.
3.1 Monitor Distance Range
Electric lens is adopted for the thermal channel of Turret Camera. It supports auto-focus
function and remote focus function. For different lens focal length, the monitoring range
is shown in the table below:
Table 3-1 Monitor Range (Pixel Interval: 17um)
Lens Focal Length/mm
1.8
3.1
6.2
MRAD
9.44
5.48
2.83
Detection Range (Vehicle)/m
162
280
559
Detection Range (Human)/m
53
91
182
Recognition Range (Vehicle)/m
41
70
140
Recognition Range (Human)/m
13
23
46
Identification Range (Vehicle)/m
20
35
70
Identification Range (Human)/m
7
11
23
Notes:
⚫This table is for reference only, and the actual detection range may vary according to
different camera settings, mounting condition, monitor and so on.
⚫When the weather is fine and the atmospheric visibility is normal, the probability of
detecting/recognizing/identifying target is50%.
⚫The human width is presumed as 0.5m (human width cannot exceed 0.75m), the
human height is presumed as 1.8m, and the vehicle width cannot exceed 2.3m.

AlphaFeverCamera Quick Start Guide
5
3.2 Install Memory Card
The micro SD card of two camera models is installed in the same way. Here is an
example of SD card installation for type II camera.
Steps:
1. Remove the cover on the back of the TurretCamera.
Figure 3-1 Remove the Cover
2. Insert the SD card to the SD card slot and install the cover back.
Figure 3-2 SD Card Slot
3.3 Install Turret Camera
Two types of cameras are installed in the same way. Here is an example of installation
for type II camera.
Steps:
1. Drill the hole on the wall or the celling according to the supplied drill template