Alptop Security AT-100BW User manual

Wi-Fi IP CAMERA
OPERATION GUIDE
www.alptopsecurity.com
[e-mail]
Apply for Model: AT-100BW/200BW/500BW,AT-200DW/PW/TW,AT-500PW/20
Note: Due to the continuous updating of the product and software, there may be a discrepancy between the
operatingguideandtheAPPinterface.Alltheinstructionsaresubjecttotheactualoperation interface.

Contents
1. Introduction.....................................................................................................................................................- 3 -
2. Installation.....................................................................................................................................................- 4 -
3. SD Card Slot.....................................................................................................................................................- 5 -
4. APP Download.....................................................................................................................................................- 6 -
5. Accessing via Camhipro APP ....................................................................................................................... - 7 -
5.1 LAN Mode Configuration..........................................................................................................................- 7 -
5.2 AP Mode Configuration(For IOS Device) ..................................................................................................- 8 -
5.3 AP Mode Configuration(For Andriod).....................................................................................................10
5.4 APP Function Introduction.........................................................................................................................12
5.4.1 Camera Interface introduce....................................................................................................12
5.4.2 SD Card Setting ..........................................................................................................................12
5.4.3 Time Setting.................................................................................................................................13
5.4.4 Camera Alarm Setting ...........................................................................................................13
5.4.5Record to SD Card Setting .................................................................................................. 14
5.4.5.1 Alarm Recording to SD Card Set-up……………………………………………….14
5.4.5.2 Schedule Recording to SD Setup…………………………………………………..15
5.4.6 Watch and Playback the local recording……………..............................................................17
5.4.7 Pre-set points............................................................................................................................. 18
5.4.8 Night Vision Mode Switch setting..............................................................................................18
5.4.9 How to Share Your Camera with More Phone Users ……………......................................19
5.4.10 Email setting..............................................................................................................................20
5.4.11FTP setting................................................................................................................................ 20
6. Accessing via Web Browser .................................................................................................................................. 21
6.1 Search IP Camera.........................................................................................................................................21
6.2 View Video by Browser...............................................................................................................................21
6.3 Interface.......................................................................................................................................................21
6.4 Parameter Settings.....................................................................................................................................22
6.4.1 SettingMedia................................................................................................................................. 22
6.4.2 SettingNetwork............................................................................................................................. 23
6.4.3 SettingAlarm................................................................................................................................. 24
6.4.4 Setting Advanced ..................................................................................................................... 24
6.4.5 Settings System.........................................................................................................................25
7. Accessing via Client Software (HIP2P Client)...................................................................................................... 26
7.1 Software installation...............................................................................................................................26
7.2 Add Camera.....................................................................................................................................................26
7.3 Delete camera………………………………………………………………………………………… 29
Frequently Asked Questions.................................................................................................................................... 30

1. Introduction
Thanks for buying Wi-Fi IP Camera. We provide IP cameras which has different
appearance and function. We follow the people-oriented design philosophy, these
five cameras will be easily able to integrate into our daily lives, both in terms of
appearance and function. This manual describes all the parameters, functional
structure, how to use, common problems and solutions for the camera in detail. This
would help you know the camera quickly and use it easily.

2. Installation
the image is only a reference

3. SD Card Slot
BC5
the image is only a reference

4. APP Download
Download APP “CamHipro” from Google Play or Apple Store, or scan the
QR Code to install.

5. Accessing via Camhipro APP
There are 2 methods to configure WiFi connection with the CamHipro APP.
A.LAN Mode Configuration:The camera needs to be connected to the router with a network cable.
The network cable can be pulled off after the WiFi connection is completed.
B.AP Mode Configuration :The camera does not need to be connected to the router with a network cable.
Please choose either of the two methods to configure your camera. Never use the two methods at the
same time.
5.1 LAN Mode Configuration
1) Use the attached power adapter to plug the camera in power.
2) Connect the camera with the router via an ethernet cable.
3) Please connect your phone to the 2.4Ghz wifi firstly before you pair the camera, make sure your
router password in mind before you start the pairing process. Please avoid using special characters
such as #, *, &, = in your router password. ( Only AT-200DW has this limitation,other models do not
have this limitation.)
4) Open CamHipro APP.
5) Tap”Click Add device”Tap “IP camera”Tap “New device”
6) Tap “power is on,next step”Tap "Connected network cable” Tap "Refresh” to search the UID
of the camera and tap it.

7) Tap 'Add to'.
Note: The default user name and password are both set as admin
8) Choose WiFi name and input your WiFi password, and tap "Configure wireless and add'.
Note:only 2.4ghz WiFi is supported.
9) Select or set a name for your camera, then tap 'confirm'.
10) Then you can remove the ethernet cable and choose a location within your local WiFi range to
install the camera.
Note: If you are unsuccessful, It will still display “connecting”. Then you have to go to "settings"
to delete the camera and start all over.
5.2 AP Mode Configuration (Connect Hot-Spot) For IOS device
When there is no visible router with network cable port for configuration, please apply the AP mode
to configure the camera with your local Wi-Fi network.
1) Enable the Phone's GPS function.
2) Have camera powered, don’t connect the network cable.
3) Please reset the camera by pressing the camera reset button for 10s.

4) Wait for about 30s, Please kindly click ‘Setting’ on your phone - Click ‘WLAN’ - Choose the WLAN
with the name starts with ‘IPCAM-XXXXXX’ - Insert the default password ‘01234567’ - Click ‘Connect’.
And your phone has been connected the the camera's Wi-Fi Hotspot now.
Note:
Name of SSID: IPCAM-XXXXXX Default password: 01234567
5) After confirming your phone has been connected to the camera’s WiFi Hotspot.
6) Open the CamHipro APP.
7. Tap “Click Add device”Tap “IP camera”The hotspot device UID will be
found,Tap “Yes,I WANTTO ADD
THIS CAMERA”

8.Tap “ADD TO”.
9.Choose 2.4ghz WiFi name and input your WiFi password, tap " Configure wireless add directly”
10.Select or set a name for your camera, then tap 'confirm'.
The device has been added successfully.You can tap confirm and go into camera interface.
5.3 AP Mode Configuration (Connect Hot-Spot) For Android device
When there is no visible router with network cable port for configuration, please apply the AP mode
to configure the camera with your local WiFi network.
1) Enable the Phone's GPS function.
2) Have camera powered, don’t connect the network cable.
3) Please reset the camera by pressing the camera reset button for 10s.
4) Open CamHipro APP.
5) Tap “Click Add device”Tap “IP camera”Tap “New device”

6) Tap “power is on,next step”Tap "Not connected to network cable' Go to AP distribution
network equipment and Tap "Go add'
7) Input password:01234567,Tap “GO TO CONNECT”.
8) Tap “ADD TO”, The default username and password are both set as admin.
9) Select your home 2.4ghz WiFi and input the WiFi password, tap "Configured wireless and add”
10) After configuration, you can view the real-time video and install the camera at a location within your
local WiFi range.

5.4 APP Function Introduction
5.4.1 Camera Interface introduce
5.4.2 SD Card Setting
a. Click icon,go to the camera setting page.
b. Please click ‘SD Card Setting’ on the main menu interface. And then you can check the storage space
information of the SD card. Or Format the SD card. Please remember to back up the data before
formatting the SD card.

5.4.3 Time Setting
a. Click icon,go to the camera setting page.
b. Please click ‘Device Time Setting’ on the main menu interface. And then you can click on ‘Sync phone
time to device’ to make the device time zone the same as your phone’s time setting. And you need
choose to set up ‘Device Time Zone’ same as your time zone. And select the ‘Daylight Saving Time (DST)
according to the season time of the year.
5.4.4 Camera Alarm Setting (Enable phone notification push function)
a. Click icon,go to the camera setting page and tap ‘Alarm management and notification’
b. Enable ‘Receive alarm push’ to push alarm notification to your phone.
c. Enable ‘Motion Detection alarm’ and adjust the sensitivity of motion detection.

5.4.5 Record to SD Card Setting
5.4.5.1 Alarm Recording to SD Card Set-up
Go to setting -‘Alarm management and notification’ page, enable ‘Motion
detection alarm’and ‘Alarm recording to SD card’.
Note: Please activate the audio icon if you need records with audio.
Playback and Download AlarmRecordings saved on the micro SD card
a. Click icon,Go to ‘Recordings’ page.
b. There have two ways to view recordings.Time playback and File playback.
Note:There is currently no distinction between scheduled
recording and alarm recording in time playback.
c. Here you will be able to see the latest alarm recording, please check the red font, a video
file named “Alarm recording”. To view more recordings, please click ‘ ’ on the buttom
right side to get other recordings.
Note:Each alarm recording time is fixed, about 15 seconds
d. Select a Alarm recording, tap ‘play’ to playback it. Tap ‘download’ to download it.

e.After downloading a recording file, you can tap ‘Go to view’ to view the recording.
You can also tap to view the recording after downloading a recording file.
f. Go to the recording file folder to check the downloaded recordings. Choose ‘Video’ on
the top.The remote recording and local manual recording will be saved here.
Please choose “remote download”and you will find downloaded Alarmrecordings.
g. If you want to convert the video format to MP4 format, please kindly follow the
image instruction.Click “”icon and choose “determine”.Then the recording
shall be viewed in the album or file manager.
5.4.5.2 Schedule Recording to SD Setup
a. Click setting icon and gon into SD card plan recording page
b. Enable ‘record’. And you can set ‘Recording Length’ to 15~900 seconds.
c. Set the date and time you want the camera starts and stops to record in advanced settings.
Instructions for advanced settings are as below.

Note:if you just need alarm recordings in your SD card,please don’t enable record
on SD card plan recording.
Playback and Download Schedule Recordings saved on the micro SD card
a. Click icon,Go to ‘Recordings’ page.
b. There have two ways to view recordings.Time playback and File playback.
c. Here you will be able to see the latest plan recording, please check the red font, a video
file named “Plan recording”. To view more recordings, please click ‘ ’ on the buttom
right side to get other recordings.
Note: Plan recording file time can be set to 15-900seconds
d. Select a plan recording, tap ‘play’ to playback it. Tap ‘download’ to download it.
e.After downloading a recording file, you can tap ‘Go to view’ to view the recording.
You can also tap to view the recording after downloading a recording file.

e. Go to the recording file folder to check the downloaded recordings. Choose ‘Video’ on
the top.The remote recording and local manual recording will be saved here.
Please choose “remote download”and you will find downloaded planrecordings.
h. If you want to convert the video format to MP4 format, please kindly follow the
image instruction.Click “”icon and choose “determine”.Then the recording
shall be viewed in the album or file manager.
5.4.6 Watch and Playback the local recordings saved on your phone
When you manually record to the phone,You can go to the local file folder and check the manual
recordings.
Go to the recording file folder to check the downloaded recordings. Choose ‘Video’ on the top.
The remote recording and local manual recording will be saved here.Please choose “Local
recording”and you will find it.

5.4.7 Pre-set point
Click the camera into real-time monitor, turn to next page.you can set the preset position.
5.4.8 Night Vision Mode Switch (AT-200PW/500PW don’t support color night vision function)

5.4.9 How to Share Your Camera with More Phone Users
When you can use your camera properly. You can start to share your camera to your friends or family
members.
a. Return to the main interface of the camera, you will see the camera's UID: SSSS-398998-BBFDA. As
shown below, Each camera has a different UID.
b. You need to send the UID to your family members or friends.
c. Your friends or family members need to install camhipro app on phone..
d. Open CamHipro APP,Click add device,IP camera,Device in use in turn.
e. Enter the UID of the camera to be added, enter the user name and password at the same time, the
default is admin/admin. If the password is modified, please fill in the modified password.
f. The device has been added successfully

5.4.10 E-mail setting
Take gmail as an example, SMTP server: smtp.gmail.com
OR PING this domain address smtp.gmail.com,Then enter the IP address of PING in SMTP server.
Server Port: 465, Safe link: SSL
Authentication: default(on)
User name: Your sender email address
Password: Gmail login password
Send To: Mail address for receiving notification (Can be the same as Sender’s also).
Sender: The same as your sender email address (Must be an email address).
Please sign in to Gmail and allowing 3 party apps to access Gmail, less security.
If not successful, please set a app password of gmail instead of password.
5.4.11 FTP setting
Operation: Please click ‘Configuration FTP’ on the Alarm management interface. And insert the relevant
information on the pop-out page. And then click ‘Test FTP Settings’ to check whether the snapshots/
videos are sent to the FTP successfully. If yes, please click ‘application’and the setting is successful.
Note:
a) Please keep the user name and password within 8 letters and avoid using special characters
such as #, &.
b) If you confirm that all the information is correct, but the testing result keeps indicating ‘Test failed’,
please log in your FTP server to check whether snapshots/videos are received successfully. If yes, go
directly click on ‘application’.