American International GMK325BM User manual

Ameritan
International
Car Stereo Installation Kits & Accessories
VBIICLE APPLICA110NS
Clalolet
2014 SILVERADO
G.:
2014 SIERRA
NOTE: THIS INSTALLATION KIT REQUIRES PROFESSIONAL INSTALLATION.
MAJOR SUB-DASH MODIFICATION IS REQUIRED TO FIT RADIO.
SUGGESTED: MOVE ONSTAR TO LOWER SUB-DASH LOCATION.
©2013 AMERICAN INTERNATIONAL INDUSTRIES, INC. TECH
Ver. 10/13 PRINT Ver. 10/13

DASH
DISASSEMBLY
INSTRUCTIONS
1.
Unsnap and remove center dash trim piece from around the radio
and climate controls.
2.
Remove (4) screws from the radio and climate controls.
3.
Remove radio and climate controls. Unplug all harnesses and antenna connections.
4.Remove the climate controls, to be installed into GMK325 panel.
KIT
ASSEMBLY
INSTRUCTIONS
Single
•
Malllt
Appllc:alons
1. Attach the left and right side brackets to the main bracket.
2.
Insert pocket (part
#
UNIPOC) into lower section of the main frame.
3.
Attach left and right side brackets to the rear of the pocket using screws supplied.
4.
Insert DIN sleeve from your new radio into the upper section of
the installation kit.
Fig.
A
2
Left
UNBIK

KIT
ASSEMBLY
INSTRUCTIONS
Single
ISO
Mount
Applicalions
1.
Attach the left and right side brackets to the main bracket (See Figure
C).
2.
Insert pocket
(part#
UNIPOC) into lower section of the main frame.
3.
Attach left and right side brackets to the rear of the pocket using screws supplied.
4.
Attach (1) ISO Spacer to the inside of upper section on both Left
&
Right mounting
brackets as shown
in
Fig.
B.
5.
Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with
kit.
NOTE:
Use
longer
screws
in
kit
for
upper
radio
location.
·
6.
Slide radio component forward or backward for desired look and tighten screws.
7.
Attach a rear support bracket to the rear of the new radio and adjust as necessary to
attach to the rear support stud located
on
the back of the pocket using the small
phillips screw supplied with kit (optional).
NOTE:
ISO
trim
ring
(UNIT1)
may
be
used
in
place
of
after-market
radio's
trim
rings.
8.
Attach (1) of the metal spring clips included to each of the
2)
mounting studs
on
the rear side of the kit.
9.
Reinstall climate controls.
Attach
(1)
ISO
Spacer
to
the
inside
of
upper
sections
on
both
Left
&
Right
mounting
brackets
as
shown
in
Fig.
B.
Fig.C
Left
UNBIK
Right
UNBI(
3

KIT ASSEMBLY INSTRUCTIONS
Double Dll Mcud lppllalllons
1. Remove the Shaded tab from the back edge of each left and right mounting bracket
(right side not shown).
2. Cut and remove center rib from main bracket and file smooth.
3. Attach the left and right side brackets to the main bracket (See Figure D).
4. Insert ISO mountable radio between ISO mount brackets and loosely attach to sidesof radio
using screws provided with radio when possible or hardware included with kit.
NOTE: Use longer screws in kit for upper radio location.
5. Slide radio component forward or backward for desired look and tighten screws.
6. Attach a rear support bracket to the rear of the new radio and adjust as necessary to attach
to the rear support stud located on the back of the pocket using the small phillips screw
supplied with kit (optional). Phillips screw supplied with kit (optional).
7. Attach (1) of the metal spring clips included to each of the (2) mounting studs
on the rear side of the kit.
B. Reinstall climate controls.
Remove the Shaded tab from the back
~~ edge of each left and right mounting
~
bracket (right side not shown).
Fig. D
CUSTOMER HELP LINE
USA 800-323-4329 • Ca1CIIa 800-245-8777 ~ ,,

MOUNTING KIT t
~~~~ L ~~~e~ o Ill II
2014 OMC SI ERR A 0
12 33903250 8