AMOD AGL 3080 Instruction manual

June 2009 AMOD Technology Co., Ltd. 1
AMOD GPS Photo Tracker AGL3080
Quick User Guide

June 2009 AMOD Technology Co., Ltd. 2
LOG GPS DATA -
Take AGL3080
along on your photo
taking trip
Turn the AGL3080 ON by pressing the
Power ON/OFF button until all three LED’s
blink simultaneously once
When the Green LED is blinking, indicating it
has started tracking the GPS satellites and
logging the GPS data
A hanging strip is provided to make carrying
the AGL3080 more convenient and
comfortable
During normal operation, if you see the
Green LED not blinking (i.e., constant ON),
adjust the orientation and position of
AGL3080 until the Green LED is blinking
again – to ensure good reception of GPS
signals
When you are in-doors or inside a tunnel, the
Green LED will be constantly on when the
GPS signal strength is too low or there is no
GPS signal to track – this is normal and you
do not need to do anything

June 2009 AMOD Technology Co., Ltd. 3
DOWNLOAD –
Download both the
GPS log (from
AGL3080) and photo
images (follow DSC
instructions)
Download picture photos to your PC
[Please follow instructions from your
DSC regarding picture download]
Plug AGL3080 to your PC’s USB port
Run the accompanying GPS Photo
Tracker software to import the GPS
log from AGL3080
[The GPS Photo Tracker Software
must be installed in your PC first. It is
very easy to use. For installation and
usage, please refer to the AGL3080
GPS Photo Tracker User Manual.]

June 2009 AMOD Technology Co., Ltd. 4
HAVE FUN –
Run the Photo Tracker
software to tag the
photos and display
them on internet map
(such as Google Map)
Preview the picture photos
Locate where the picture was
taken by displaying it on Google
Map
Save the GPS tag of your picture
photos for future use or do nothing
GPS logs from AGL3080 also
works with many other photo
organizing software
AGL3080 also works with those
photo organizing software such as
JetPhoto Studio on Apple’s MAC
operating system

June 2009 AMOD Technology Co., Ltd. 5
MARK/TAG – Depress the Mark / Tag
button after taking the picture can create a
tag for the picture in the GPS log.
GPS RESET – When the stored GPS
satellite information is out of date or out of
view, the AGL3080 may take longer time
to obtain position fix. When this happens,
depress the MARK/TAG button for about
5 sec. to perform the GPS Reset function.
This can help the GPS position fix and is
very helpful when travel from places to
places
Use it as a USB flash storage device
when needed
Many extremely
useful functions

June 2009 AMOD Technology Co., Ltd. 6
Enter Set Up Mode by holding POWER
and MARK key simultaneously for 5
seconds, and three LEDs will flash 5 times
to stop at full lit mode. You can release
the buttons when 3 LED are all on.
Press mark key to set logging mode
In the Set Up mode, to clear storage area,
press the POWER and MARK keys
simultaneously for about 5 sec
Different setting mode as below
Various logging
mode at your finger
tip
2,880 hours1,040,000Only RMC->10 secBattery Low Led FlashMode 6
720 hours260,000GGA/GSA/RMC/VTG/GSV->10 secBattery Low Led ONMode 5
1,440 hours1,040,000Only RMC->5 secGPS Led FlashMode 4
360 hours260,000GGA/GSA/RMC/VTG/GSV->5 secGPS Led ONMode 3
288 hours1,040,000Only RMC->1 secMemory Full Led FlashMode 2
72 hours260,000GGA/GSA/RMC/VTG->1 sec
GSV -> 5 sec
Memory Full Led ONMode 1
Data Capacity
Operation Hours
Minimum RecordsOutput FormatLED Status

June 2009 AMOD Technology Co., Ltd. 7
Turn ON Func Depress the ON/OFF button until all three LED’s simultaneously blink
once, then the Green (GPS Status) LED will be on, indicating the
device starts to search for GPS satellite signal
Stat When the device obtains a position fix, the Green (GPS Status) LED
begins to blink
Stat The Green (GPS Status) LED has two states – position fix (blinking)
and no position fix (constant on)
Turn OFF Func Depress the ON/OFF button until all three LEDs simultaneously goes
on and then off, indicating the device is turned off
Mark / Tag Func Depress the Mark (icon) button briefly – the RED (Storage Status)
LED will blink once, indicating the last position fix has been tagged
GPS Reset Func Depress the Mark (icon) button for about (5 seconds) and release –
the GPS will do the position fix by researching GPS satellite [so that
the satellite Ephemeris will be updated]
Clean Up Storage Func To turn on the device, make the device to enter “Set Up” mode by
pressing both Mar and Power buttons at the same time for 5 seconds
until 3 LEDs stay at lit on mode. After release both buttons, the
device is at Set Up mode. At the Set Up mode, press “Mark” key for 5
seconds to clear the storage space.
AGL3080 GPS Photo Tracker Summary of Operations and Functions