Amplifico PARKLIO ANPR User manual

PARKLIO™ ANPR
USER MANUAL

1
Dear Customers,
Thank you for the condence you have shown us by purchasing Parklio™ ANPR.
We hope that all your expectations of this product will be fullled. Parklio™ ANPR
is manufactured using the latest technologies and has undergone rigorous quality
control procedures. The User Manual will help you use your product quickly and
safely. Information contained in this manual is subject to change without notice.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliabili-
ty, Parklio™ reserves the right to make changes to the products described in this
document without notice. Parklio™ does not assume any liability that may occur
due to the use or application of the product(s) or circuit layout(s) described here-
in. Thank you for the condence you have shown us by purchasing our Parklio™
ANPR system.
Trademarks
Parklio™ is a trademark of Amplico d.o.o.
Other brand and product names are registered trademarks or trademarks of their
respective holders.

2
TABLE OF CONTENTS
1. Safety warnings.....................................................................................................3
2. Camera Installation..............................................................................................5
2.1. Before You Start....................................................................................................................5
2.2. Lens Selection.......................................................................................................................5
2.3. Installation Angle................................................................................................................6
2.4. Installation height and distance................................................................................6
2.5. Installation of the camera..............................................................................................7
2.6. Controlling a device.........................................................................................................13
2.7. Generic device.....................................................................................................................13
2.8. Parklio Devices...................................................................................................................14
3. Camera Setup.......................................................................................................15
3.1. Prerequisites..........................................................................................................................15
3.2. Camera activation.............................................................................................................15
3.3. Camera web interface.....................................................................................................18
3.4. Detection area setup.......................................................................................................21
4. Assigning camera to Parklio™ PMS..............................................................23
4.1. Installing Parklio™ Connect.........................................................................................23
4.2. Login.........................................................................................................................................24
4.3. FAQ............................................................................................................................................29

3
1. Safety warnings
This section contains safety instructions that will help to protect you from risk of
injury or property damage. Failure to follow these instructions will invalidate all
warranties.
• Do not use the ANPR camera, if you have not read and understood the operat-
ing instructions before.
• Before rst use of the ANPR camera, make sure that all the parts listed in these
instructions are inside of the original packaging.
• Only parts supplied by the manufacturer of the ANPR camera should be used.
Use of nonmanufacturer provided parts may affect the loss of warranty.
• Ignoring usage instructions, improper installation and use of the device may
result in damage to the ANPR camera or injuries to the user. Instructions should
always be at hand.
• Never expose the inner workings to water.
• The device and external supply must be disconnected from power supply
during installation, maintenance, cleaning, and repairs.
• Leave the repairs to a specialist. Improper repairs may lead to an accident or a
malfunction in the unit.
• The warranty does not cover consumable parts of the device, color fading and
chipping, increased noise due to aging of the device and other aesthetic effects
that do not affect its functionality or safety.
• Strictly follow the instructions for proper installation and connection to the
electrical network.
• Installation requires mechanical and electrical skills, therefore it shall be carried
out by qualied personnel only, who can issue the Compliance Certicate con
cerning the whole installation.
• Do not install the product in explosive environments and atmospheres, the
presence of inammable gases or fumes is a serious safety hazard.

4
PARKLIO (AMPLIFICO D.O.O.) HAS THE RIGHT TO MODIFY THE DEVICE
WITHOUT PREVIOUS NOTICE. PARKLIO (AMPLIFICO D.O.O.) DECLINES
ANY RESPONSIBILITY FOR DAMAGE OR INJURY TO PEOPLE OR THINGS
CAUSED BY IMPROPER USE OR WRONG INSTALLATION.
THE APPLIANCE HAS BEEN ESTABLISHED ACCORDING TO ALL VAL-
UENT SAFETY CRITERIA AND STANDARDS. HOWEVER, WE RECOM-
MEND THAT WITHOUT THE NEEDED HELP AND SUPERVISION, CHIL-
DREN, A PERSON WITH DISABLED PHYSICAL, MOTOR, OR PERSONAL
EQUALITY AND RELATED PEOPLE WITHOUT PREVIOUS EXPERIENCE
OR KNOWLEDGE DO NOT USE THE BARRIER. EXCEPTION IS THE DE-
VICE USAGE UNDER ADEQUATE SUPERVISION IF THEY HAVE RE-
CEIVED SAFETY INSTRUCTIONS AND TRAINING, OR IF THEY ARE IN-
FORMED ABOUT THE DANGER CAUSED BY IMPROPER USAGE. THE
SAME RECOMMENDATION IS FOR JUVENILES AND THEIR USAGE OF
THE DEVICE.
DO NOT ALLOW CHILDREN TO PLAY WITH THE DEVICE. DO NOT LET
CHILDREN CLEAN THE DEVICE, USE IT, NOR MAINTAIN IT, WITHOUT
ADEQUATE SUPERVISION.

5
2. Camera Installation
NOTE: If you are unsure how to properly install the ANPR camera, you can al-
ways schedule a video call with us via email.Our team will explain in detail how
to install ANPR camera for the optimal license plate reading.
2.1. Before You Start
The camera installation conditions should meet the following requirements:
• Trees or items should not orobscure the view of the road/vehicle entrance.
• The license plate tilt angle must be within +/-5 degrees.
To ensure accurate detection and that enough pixels are in the frame, it is required
to select a proper lens.
Steps for choosing the lens:
• Dene the Identication distance of the scene.
• To get the identication distance, dene the camera height (H).
• The detection range (L) can be calculated as L = cot 30° × H ≈ 1.73 x H
• Note: The recommended camera Height (H) is 1,6m to 2m.
2.2. Lens Selection

6
Select a proper lens according to the table below. The identication distance is
based on the camera’s focal length.
The installation angle must meet the requirements below:
• The Vertical angle should not exceed 30 degrees.
• The Horizontal angle should not exceed 30 degrees
2.3. Installation Angle
The camera Height (H) should be 1,6m to 2m.
2.4. Installation height and distance:
Camera
LPR
Camera
Lens (mm)
2.8 - 12 6 11,2
30
15
8 - 32
Scene
Entrance
Road
Trafc
Min.
Identication
Distance (m)
Max.
Identication
Distance (m)

7
Before installing the camera read the quick installation guide included in the
camera box.
The camera package should contain the following items:
2.5. Installation of the camera:
1 1x ANPR Camera
2 1x QR Code
3 8x Waterproof tape
4 4x Mounting screws with dowels
5 1x Cable gland
6 1x Allen wrench
7 1x Screw terminals
8 1x Connection cable
9 2x Quick start guide
10 1x CD
NOTE:
If any of the parts are incorrect, missing, or damaged, contact your Parklio™ deal-
er. Keep the original packing materials, in case you need to return the product for
repair.
1
2
3
456
78
910

8
Wall Mount Option
To install the camera on a wall follow the instructions illustrated below:

9
Pole Mount Option
For mounting the camera to a pole a pole mounting kit is needed. The pole mount-
ing kit is not included with the camera.
To mount the camera to a pole follow the instructions included with the pole
mounting kit.
Connections
All wiring connections should be made inside the base plate to protect them from
environmental conditions.
If connecting the camera via Ethernet use the provided gasked.
For protection other terminal connections use the provided water proof tape.

10

11
Positioning the camera
The camera can be rotated by unlocking the mount by using the provided security
screw wrench.

12

13
To enable the opening of a parking access control device (gate, chain, bollard, ...)
or other devices, connect the camera ALARM1 output (marked as 4&5 in the image
below ) relay to the device’s OPEN command input.
2.6. Controlling a device
1. Connect a cable to the camera ALARM terminal (connect to terminals 1A and 1B).
Connection is not polarity sensitive.
2. Connect the cable to the OPEN command input on the control electronics of the
device.
2.7. Generic device

14
Parklio Gate:
Connect the camera ALARM terminals (terminals 1A and 1B) to START1 (1) and COM
(6) terminals on the Gate control electronics.
Note:
When using the camera, it is recommended to enable automatic closing of the
gate
2.8. Parklio Devices
Parklio Bollard:
Connect the camera ALARM terminals (terminals 1A and 1B) to LS (15) and COM (18)
terminals on the Bollard control electronics.
Note:
When using the camera with the bollard, it is necessary to enable automatic
closing (settings: P4 -AF) and to put the bollard into Condominium Mode (settings
P7 - 02).

15
3. Camera Setup
If the network has a rewall enabled you may need to enable the camera to access
the remote hosts
it is necessary. The list of services is provided below:
3.1. Prerequisites
A PC or MAC is required to set up the camera. The computer and the camera must
be on the same network. The SADP tool is required for initial camera setup. It can
be downloaded from the link below by typing SADP into the search bar.
https://www.hikvision.com/europe/support/tools/hitools/
Fill in the search bar with SADP and click the link to download the le.
The SADP software locates Hikvision devices that are online on the network. It dis-
plays device information, can activate a selected device, edit the network parame-
ters of the device, and reset the device password.
NOTE: On Windows machines, the SADP tool can display a .dll missing error on
startup. This can be resolved by installing vcredist_x86.exe:
https://aka.ms/vs/17/release/vc_redist.x86.exe
3.2. Camera activation
Please keep in mind that the hosts can resolve to multiple IP addresses, which can change at any time.

16
In the SADP tool search the network for available devices:
Once the SADP tool is open any cameras that have not been setup will appear as
Inactive.
• To activate the camera, select the inactive camera and the Activate the Device
window will appear on the right.
• Create a password for the camera.
•NOTE: Please keep in mind that this password is only used for the camera set
up and Web Interface and not for the Parklio™ PMS.
• Once the password has been entered, click the Activate button to turn on the
camera.
• A window will appear with the option of setting security questions or providing
an email address to recover the password if it is lost.

17
Once the password recovery method has been selected, the necessary elds must
be lled out, and the changes must be saved by clicking Conrm.
It is necessary to exit this window after clicking the conrm button because it
does not close automatically after conrmation.
After that, enable DHCP and enter the password created in the Administrator Pass-
word tab before clicking Modify.

18
NOTE: If a static IP address is required, the SADP tool can be used to congure
a static IP address and network parameters by disabling DHCP and entering
network parameters.
Click the refresh button to refresh the SADP tool.
NOTE: If the Ipv4 address is set to 0.0.0.0, refresh the SADP tool by clicking on
refresh or disconnect and reconnect the camera’s Ethernet cable to refresh the
SADP tool.
Then, double-click on the camera’s Ipv4 address to open a new browser window
(or type in the address in the browser address bar).
3.3. Camera web interface
Enter the username and password for the camera’s web interface and click Login.
The default username is admin, and the password is the one you previously set. It
should be noted that the

19
camera’s default user name is always admin. From the camera’s web interface, you
can add new users and change the default name.
Go to VCA ▶ Road trafc ▶ Arming Schedule and Linkage Method.
Select All and disable the Trigger Alarm Output by clicking on the checkmark next
to the Trigger
Alarm Output. After that, click the Enable checkbox in order to enable vehicle de-
tection: