Amsino PUGGLE Specification sheet

The PUGGLE® Enteral Feeding Pump is delivered with an uncharged battery. Before use, charge by using
the AC adapter provided with the pump.
The PUGGLE Enteral Feeding Pump may be fixed onto a vertical pole using the pole clamp provided with the
pump.
Important: For the PUGGLE Enteral Feeding Pump and its alarms to operate properly, use only PUGGLE
Enteral Feeding Sets with this device. The pump is not compatible with other pump sets.
Place feeding bag above the pump.
For better accuracy, the initial fluid level shall be at
15.2 cm (6.0 inches) higher than the pump and the
pump shall be placed higher than the injection site.
Do NOT use homemade or non-prescribed formula.
The setting range of operating head height is
0~50 cm (0~19.68 inches) which has been
verified as worst-case condition.
Quick Set Up
15.2 cm (6.0 in.)
Feeding Bag Placement
1. Open pump cover.
2. Place the silicone loop around the rotor and make sure the cassette is
in the right direction.
3. Push the cassette in the middle of the pins with your thumb and make
sure the cassette is positioned correctly between the two black pins.
Guide both tubes down, in line with their respective slots.
4. Close the pump cover, then place the adapter into the designated slot.
Remove the protective cap from the distal connector (end of down-
stream tube that goes on the patient’s feeding tube).
Launch automatic priming.
Connect the tubing to the patient enteral feeding tube and program
the pump.
1. 2. 3. 4.
Tubing Diagram
Silicone loop
Cassette
Upstream tube
Downstre
am tube
Adapter
Loading Disposable Set
Scan the QR code to view the
PUGGLE Enteral Feeding Pump
Instructional Video

Action Effect Screen Displays
2 steps to launch priming:
• Press – Prime message appears
• Press multifunction button
[] – Launch prime
• Automatically primes pump tubing
• Duration: Approx. 1 min. 25 sec.
• Automatic priming may be stopped
before completion by pressing
multifunction button [ ]
After the 1 min. 25 sec. priming
is completed or after pressing
multifunction button [ ]
• Priming is completed
• Verify the tubing is fully primed
Press multifunction button [ ] • Program the feeding
Tube Priming
Action Effect Screen Displays
Press or then multifunction
button [ ] • Set the flow rate from 1 to 400 mL/h
Press or then multifunction
button [ ]
Choose your volume option:
• Press to use entire bag*
• Press to set the volume to be
delivered (this value must be from
1 to 9,999 mL)
Press multifunction button [ ]
• Overview of the feeding parameters
(with or without a programmed
volume)
Press multifunction button [ ]• Start the feeding (with or without a
programmed volume)
Programing Nutrition – Continual Feeding
*Use entire bag: If the user selects the multifunction button [ ], the pump will be programmed to operate without setting a specific volume.
The pump will operate until the feeding bag is empty.
During the feeding, it is possible to lock the keypad. This feature allows deactivation
of the keypad buttons.When the keypad is locked, the pump cannot be paused or
switched off. To lock the keypad press and buttons together for 3 seconds. Do the
same action to unlock it. The key icon [ ] appears in notification header when the
keypad is locked.
Special case:When the alarm is triggered, the keypad automatically unlocks.
Amsino Medical Group Co. Ltd.
708 Corporate Center Drive, Pomona, CA 91768 USA
+1 800.632.6746 • fax: [phone] • [e-mail]
EN-US-2023-08-04
Product(s) described may not be licensed or available for sale in all countries. Please
see the Instructions for Use/Operator’s Manual for a complete listing of the indications,
contraindications, warnings and precautions. The symbol ®indicates the trademark is
registered in the U.S. Patent and Trademark Office and certain other countries. Puggle
is a registered trademark of Amsino Medical Group Co. Ltd. © Copyright 2023, Amsino
Medical Group Co. Ltd. All rights reserved.
Locking Keypad