anko Wooden Cot In Oak Colour User manual

2
Supplied loose in box
Read these instructions carefully before use and keep for future reference. The child may be hurt if
you do not follow these instructions.
M6*55mm
x8
M6*40mm
x4
M6*35mm
x22
M6*15mm
x4
(Pre-assemble)
84
A B C D
E
I J LK
FHG

Do not firmly tighten bolts / screws.
Pre-drilled holes face inside.
J x6 G x4
J x8
H x4
H x4
I x2
A
B
B
D
E
F
D
21
43
65
87
3
H x4
A
B
J x4
D G
E
C
I x2

4
9 10
J X4
G X4
G
E
D

5
Mattress Base in Low Position
This base height is set for an active baby who
can sit up unaided.

6
21
43
65
7
K X4
K X4 I X4
I X4
NOTE: Loosening the bolts
of one side panel will assist
in avoiding any scratches or
dents to your Cot whilst sliding
the mattress base down to the
lower position. If side panel
bolts are loosened during this
process, ensure they are re-
tightened after you have moved
the mattress base.
Lay Cot on Side Panel.
Remove mattress
base bolts.
Remove Lower setting
mattress base fitting
bolts.
Re-fit mattress base
bolts in lower
position to secure.
Stand Cot upright.
Fit 4 x K bolts into
top mattress base
holes.
Carefully slide
mattress base down
to lower height
setting until dowels
align with lower
dowel holes.
Lay Cot on Top
side.
Re-fit feet panels
to underside of
Cot.

7

8
ADULT ASSEMBLY REQUIRED:
DUE TO THE PRESENCE OF SMALL PARTS DURING ASSEMBLY, KEEP
OUT OF REACH OF CHILDREN UNTIL ASSEMBLY IS COMPLETE.
TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE
ADJUSTED TO THE LOWEST POSITION BEFORE THE CHILD CAN
SIT UP UNAIDED.
RECOMMENDED MATTRESS SIZE:
690mm WIDE x 1300mm LONG AND NO MORE THAN 150mm THICK.
FOLLOW THE MANUFACTURER’S ASSEMBLY INSTRUCTIONS
TO ENSURE THE SAFETY FEATURES OF THE COT ARE NOT
COMPROMISED.
This cot has been manufactured for one child only, with a maximum weight
of 18kgs.
When the mattress base is assembled in the lower position, ensure the higher
ENSURE the cot is placed at a reasonable distance from curtains, blinds,
heaters and power points.
ENSURE the cot is completely assembled and check that all parts are
securely tightened before placing the child into the cot.
ENSURE medication, string, elastic, small toys or small items such as money
etc are always kept out of the child’s reach when in the cot.
DO NOT over tighten bolts/screws.
ENSURE that the child is clear of any moving parts when adjusting the cot.
For warranty purposes, keep your sales receipt to provide proof of purchase.
RECOMMENDED MATTRESS SIZE (SOLD SEPARATELY):
THIS COT HAS BEEN MANUFACTURED FOR USE WITH A MATTRESS
WHICH MEASURES 690mm WIDE x 1300mm LONG AND NO
MORE THAN 150mm THICK.
WARNING:

9
• To ensure the long-lasting use of your cot, wipe down with a damp cloth
and use a mild soap solution if necessary.
• Do not use abrasive cleaners.
• Always store product in a clean dry place.
• Always check parts regularly for tightness of screws, nuts and other
fasteners – tighten or replace if required.
• To maintain the safety of your cot, seek prompt repairs for bent, torn, worn
or broken parts.
• Use only those parts and accessories approved and supplied by the
manufacturer.
the gaps
between the mattress and the sides and ends of the cot will not exceed 40
mm when the mattress is pushed to one side or end, and 20mm when the
mattress is centred in the cot.
This is to minimise the danger of a child’s limb becoming caught in the gap.
the depth
of the cot is greater than 500mm with the mattress base in the lower
position and is greater than 300mm with the mattress base in the upper
position to minimise the risk of a child climbing or falling out of the cot.
CARE AND MAINTENANCE: