Anycom EDR-AP User manual

1
ANYCOM Technologies AG
www.anycom.com

2
■ Table of Contents
1. EDR-AP KEY FEATURES ..................................................................................... 3
2. PART CHECKLIST .............................................................................................. 3
3. PRODUCT DESCRIPTION ..................................................................................... 4
4. SPECIFICATION ................................................................................................ 5
5. CONTROLS AND FUNCTIONS [BUTTON/LED/PEAR PANEL] ......................................... 6
6. EDR-AP INSTALLATION ...................................................................................... 9
7. CAUTION ........................................................................................................ 11
8. CONFIGURATION USING WEB INTERFACE ............................................................... 12

3
■ EDR-AP Key Features
zEDR-AP supports Bluetooth LAP / PAN / DUN / OPP Gateway.
zEDR-AP provides a built-in web server for convenient configuration.
zEDR-AP support private leased lines, ADSL/VDSL modems using PPPoE and cable modems (DHCP).
■ Part Checklist
Please check and make sure that you have the following package contents.
Item Q’ty Use
EDR-AP Body 1 EDR-AP main body
User Manual 1 User guide that explains features, functions and
implementation examples
Antenna 1 Bluetooth Antenna
Power Adapter 1 EDR-AP power supply device (5V 1A)
LAN Cable 1 Cable that connects EDR-AP and Internet Modem

4
■ Product Description
Please check and make sure that you have all the following package contents.

5
■ Specification
Name Description
Output Power 15 ~ 20 dBm
Rx Sensitivity 85 dBm
Channel 79 CH
Antenna 2.4GHz Band 1/2λSleeve Dipole Antenna
Frequency 2402 ~ 2480 MHz
Modulation FSK, QPSK
Adaptor 5V 1A
Max Current 560mA
Operating Temperature -20℃~55℃

6
■ Controls and Functions
▌ Button
Name Description
Button If you press this button, the LED (Green) blinks and EDR-AP goes to discoverable and pairable
mode.

7
▌LEDs
Name Color Status Description
ON Power is ON and Bluetooth is normal state mode
BLINK Other device is connected and new device is under pairable
mode
STATUS Red
OFF Power is OFF or Bluetooth is abnormal state mode
ON TCP/IP communication is able mode
BLINK TCP/IP communication is disable mode
WAN Green
OFF Not connecting with the Ethernet
* When EDR-AP restarts, every LED blinks several times

8
▌ Rear Panel
(From the left to the right side)
Name Description
RESET
Press this button for more than three seconds to restore the original factory default setting of
EDR-AP
(Reboot: press under three-seconds)
5V1A Connect the Power Adaptor
WAN Connect to private leased line, ADSL/VDSL modem, cable model using LAN cable (UTP
Cable)

9
■ EDR-AP Installation
Please check the port location of the rear panel and then follow the steps below to install the EDR-AP properly.
▌ Ethernet Network Connection
Let’s check the Network cable connection to use the high-speed internet service.
Modem
① Pull out the cable from the Ethernet (LAN) port of ADSL modem and connect it to the WAN port at the EDR-AP’s
rear panel.
② Connect the power adaptor to the “POWER” port at the EDR-AP rear panel.

10
③ Connect antenna provided to antenna connecting jack at the side of body. When you connect antenna, twist it on
carefully and lastly push it strongly.

11
■ CAUTION
zUse only the power adaptor supplied. Using other power adaptors may cause the voice quality to deteriorate and
malfunction.
zInstall EDR-AP far from wireless LAN/microwave about 1m. If installed close may cause jamming.
zUse only the antenna provided.

12
■ Configuration using Web Interface
You can use Web Interface with web browser in order to set the EDR-AP configuration. You can access the Web
Interface by IP address or Bluetooth connection (LAP/PAN). For the access by Bluetooth connection, connect with
LAP/PAN of EDR-AP and access with Gateway address assigned from the PC.
▌ Checking device’s IP address
In case of you don’t know the IP address, you can check the current EDR-AP IP address by configuring IP address of
user’s PC.
① Click [Start] from the bottom menu bar, then choose [Settings].
② Select [Control Panel] to view a new window, and then choose [Network connections].
③ Right click on [Local Area Connection]. If there are more than one Local Area Connections, choose the one that
is currently in use.
④ Choose [Properties] when a new window appears.
⑤ Click [IP Address] tab and then check the [Obtain an IP address automatically] box. If the box is already checked,
you don’t need to change anything.
⑥ Click [Ok]. You don’t need to restart your computer in Windows XP.
Access to the Web Page: http://192.168.2.1:1001/index.html. You can set the functions below through Web Page.

13
When you access configuration page, User ID and Password are required.(default - User ID: admin, Password : 0000)
▌ Configuration
Name Detailed Name Description
System Status You can check the status of EDR-AP.
Technical
Specification
You can check the information about firmware, software, hardware of EDR-
AP.
System Information
Bluetooth
Clients Bluetooth Client display
Network You can configure the network environment for the internet use.
(Choose the network among Static IP, DHCP, ADSL(PPPoE))
Bluetooth
You can set the environment for the Bluetooth use.
You can configure the Device Name, Security Level, Pin Code, Select
Power Class.
Radius You can configure the Radius authentication method and information.
SNMP You can configure the information for the interoperate with SNMP server.
Service Mgmt You can configure the ID, Password of the EDR-AP.
Configuration
Factory Reset System reset by factory value
System Restart Restart EDR-AP

14

15
▌ Network Configuration
① Select [Configuration], and then choose [Network] to enter the network configuration page.
② Now select and set the appropriate IP configuration parameters that match your network environment from below.
(a) Static IP
i. Select [Static IP].
ii. Enter the IP, gateway, network mask and DNS address for EDR-AP.
(b) DHCP(Dynamic IP) or Cable modem
i. Select [DHCP].
(c) ADSL(PPPoE)
i. Select [ADSL].
ii. Enter ADSL ID and the password.

16

17
▌ Bluetooth Configuration
① Select [Configuration], and then choose [Bluetooth] to enter the network configuration page.
② When the pop up window requesting ID and Password, type USER ID: admin, Password: 0000.
Title Description Default
Value
Device Name Means the name of the device. Choose the “User Defined” and
type the name you wish. Use Default
Security Configuration
Set the Security Level.
Level 1 : Security Code(Pin Code) Is not requested.
Level 3 : Security Code(Pin Code) Is requested.
Level 3
Device Configuration
Check PIN Code
Access Mode is set for search
000000
Radio Power Class Select the Sending Power of EDR-AP. Class 1 is the strongest
electric wave. Class 1
PROFIT

18

19
▌ RADIUS
① Select [Configuration], and then choose [RADIUS] to enter the network configuration page.
Title Description Default
value
Retransmission Define the number of re-transmission times in case of data
failures when interoperate with Radius server. 1
Timeout(sec) Set the time interval for Retransmission. 5 sec
Authentication Server Set the domain or IP address of Radius Server.
Authentication
Password
Set the Password to receive the authentication from the Radius
Server.
Authentication Port
Number Set the Port Number of Radius Server. 1812
ACCESS MODE

20