Anzzi L-AZ021 User manual

ASME A112.18.1/CSA B125.1
L-AZ021
The tools might be applied to the following places:
Daily cleaning and care are required in order to keep the product shining and
properly working.
1
2
3
4
Clean it with water and dry it with soft cloth.
Clean the product with gentle liquid or glass cleaner.
Don't use acid cleaner.
Don't clean with abrasive material, abrasive paper or knife.
Step 4 Parts list
SINGLE HANDLE LAVATORY FAUCET
PART NAMENO.
1
2
3
4
5
6
Handle
7
8
9
10
Screw
11
12
13
14
15
16
17
18
19
Clamp
Lock nut
Rubber washer
Screw
Trim cap
O-ring
Cartridge lock nut
Body
Aerator core
Cartridge
Washer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
20
21
22
23
24
25
26
Screw
O-ring
Cartridge adapter
O-ring
Screw
O-ring
Core
Screw
Index
Aerator collar
Cover
Allen key
26
Flexible hose
Channel Locks
Adjustable Wrench
RECOMMENDED TOOLS
Attention:
for easy installation, you will need:
1.To read all the installation instruction completely before
beginning.
2.To read all the warning, attention and maitenance
information.
3.To purchase the proper supply lines.
Allen key
WARNING:
Please keep the
tool for future
use!
Goggles
Teflon tape
Basin wrench
INSTALLATION MANUAL
1-844-44-ANZZI or visit www.ANZZI.com
Per fection is our Tradition
MT
Step 3 Cleaning and care

Step 1 Faucet installation
Faucet installation
2
1
3
HOT COLD
HOT COLD
1.Assemble the 2 flexible hose to the faucet by hand.
2.Put the faucet into the installation hole of the basin. Make sure o-ring be on the base of faucet. Assemble screw #23
to the base of faucet, and assemble rubber washer #21 and clamp #22 to screw #23. Then assemble lock nut #24 by
basin wrench to screw #23 to fix the faucet.
3.Connect the to water supply valve (not included), and tighten it with adjustable wrench.
DON'T OVER TIGHTEN!
Caution: make sure connect the hot and cold flexible hoses to supply valves correctly.
flexible hose
Warning:
The supply valves are not included, please purchase them in plumb shop.
O-ring
23
21
22
24
Step 2 Checking and testing
1.Remove the aerator by . Turn the faucet handle all the way on, turn on hot and cold water supply and flush
water lines for one minute. Reinstall aerator by hand.
2.Check all connections at arrows for leaks, re-tighten it if necessary. BUT DON'T OVERTIGHTEN!
hand
Pop-up installation
2
1
lift rod
faucet
body
extend rod
horizontal rod
screw
fittings
1.Remove pop-up drain stopper, and flange with top rubber washer for pop-up assembly. Insert drain body from
underneath of sink drain hole. Replace flange and top rubber washer back to drain body. Tighten flange as far as
possible. Remove and put silicone along bottom of. (Optional) Slide bottom rubber washer on drain body up against
bottom of sink. Tighten washer and locknut firmly against base for tight seal. Remove tailpiece from drain body, add
Teflon tape, replace tailpiece.
2.Replace pop-up drain stopper to drain body with o-ring in place, and align stopper hole with guide rod opening.
3.Remove rod guide nut and rod ball plastic gasket. Insert horizontal rod into drain body and through hole in drain
stopper. Replace rod guide nut with rod ball plastic gasket and tighten it.
4.Insert lift rod through hole on faucet body. Connect extend rod to lift rod. Attach horizontal rod to extend rod using
fittings, tighten screw.
rod guide nut rod ball
plastic
gasket
drain
stopper
hole
drain body
o-ring
sink
drain stopper
flange
align hole in
drain stopper
with guide rod
opening
(pointed toward
back wall)
flange
drain body
top rubber washer
sink base
locknut
washer bottom
rubber
washer
tailpiece
horizontal rod
drain body
123 4