Aplus AP7000RF User manual

- AP7000RF USER MANUAL
Read the safety precautions in this section before installing, powering, operating or servicing this product.
【SAFETY PRECAUTIONS】
WARNING!
Safety hazard. Can result in shock from battery or product damage. Cleaning and Installation Care.
 Lighting fixture is for INDOOR use ONLY.
 Do not use parts or materials other than the supplier parts to
install this product
 To avoid accidents do not change or modify this product in any
form or method.
 Do not replace batteries when your hands are wet to avoid risk of
shock or product malfunction.
 Do not look directly at LED to minimize the risk of eye irritation
or injury.
 Not for use in high temperature, humidity, direct sunlight or
where it may be exposed to rain or water.
 Wipe and clean product with a dry soft cloth ONLY. DO NOT spray
any type of cleaning solution directly onto the product as it will
damage the device. Never clean with harsh chemicals such as alcohol
or solvents.
 Ensure that product is mounted securely to the wall to prevent
personal injury and /or product damage as a result of product falling.
 Do not install near electric doors or other devices that use radio
waves as to not interfere with this product or radio wave devices.
 Do not mix old and new batteries, alkaline and carbon-zinc or
rechargeable batteries.
 Do not install this product near high temperature equipment such as
heaters to avoid sensor failure.
 Install the device according to the user manual and installation
instructions.
 Use this product within the room temperature range of 0-40℃
(32-104℉).

 Be careful of battery polarity when installing batteries.
 If the product malfunctions in any way, stop using the product and
contact the original seller.
 Remove batteries when not in use for long periods.
About radio wave
This product uses the 2.4 GHz frequency band. Other wireless devices may also use the same
frequency, so please pay attention to the following to prevent radio waves from interfering
with this device.
In the frequency band used by this product, in addition to industrial, scientific, and medical
equipment (such as microwave ovens), there are also radio stations for mobile object
identification that require a factory production license, specific low-power radio stations that
do not require a license and amateur radio stations, etc. (Hereinafter referred to as "other radio
stations").
1. Before using this product, please make sure that no "other radio stations" are operating
nearby.
2. If this product causes radio wave interference to "other radio stations", please immediately
change the place of use of this product or stop using the device.
If this product is too close to other devices that use the 2.4 GHz frequency band, it may cause
problems or malfunction due to radio wave interference.
 Communication may not be possible in the vicinity of a broadcasting radio station.
 If there are shelters between the linkable devices or due to the influence of the building
structure, the transmission distance may be shortened.
 Interference shelters will absorb electromagnetic wave energy, attenuate the transmission
signal, or shorten the transmission distance. The degree of influence depends on the material
and thickness. According to the degree of possible interference, it can be divided into the
following 4 categories. When installing, avoid "very high interference" shelters as much as
possible:
◎ Low interference: such as wood, glass and many synthetic materials
◎ Moderate interference: such as water, bricks, marble
◎ High interference: such as plaster, cement
◎ Very high interference: such as metal
About sensors 
The sensor responds to changes in brightness and temperature. For example, if it is installed in the following places, it may not work properly or malfunction. The transmit and receive sensitivity of
the linkable wall lamp will vary with the use environment, the following conditions / locations must be considered before installing:
 Places with strong radio waves
 Places with glass such as glass doors
 Places where wind blows (near windows, etc.)
 Places where pets such as dogs or cats will pass
 Near high-temperature objects such as heating
 Close to other lighting equipment
 Objects that will shake due to wind, such as curtains
 Glass between the lights may cause poor linkage function,
such as doors and fish tank
【PRODUCT】 【CONTENTS】
Model No.: AP7000RF
Light body ABS-plastic, PCBA 1 pc
Backplate Stainless steel SUS304 1 pc
Self-tapping wood screw Steel 2 pcs
Double-sided tape Adhesive 1 pc
Manual Paper 1 pc
Power source: 3*AA alkaline dry batteries (not included)
【DIMENSIONS】 unit: mm (inch) 【SPECIFICATIONS】
LED type * quantity SMD * 1 pc
Color temperature 3000K±500 (warm white)
Luminous flux About 25 lumens
Length of lighting About 15 seconds
Human body sensor PIR (Passive InfraRed) motion sensor
Ambient light sensor Light sensor
Wireless transmission method RF (Radio Frequency) 2.4 GHz
Wireless transmission distance About 20m (65’), distance without shelter
PIR sensing angle About 120°
PIR sensing distance About 150cm (60”)
Power source 3*AA batteries (not included)
Battery life ≧12 months (at 8~10 activations/day) or
≧4,000 times
Low battery indicator When the battery capacity is low, the red
warning light flashes every 3 seconds.
Weight Body (excluding battery) About 68g (2.40 oz)
Backplate (excluding tape) About 15g (0.53 oz)
“Linkable wall lights” are LED wall
lamps that use RF (Radio Frequency)
transmitting and receiving technology to
communicate between lights. When the
surrounding environment becomes dark,
the motion sensors on the lights will
activate. When someone is detected b
y
the sensor the LED will light up an
d
communicate to the other lights in the
p
ath to light up at the same time creating
a safe lighting path.
Body
Backplate

【MOTION SENSOR SENSING RANGE】
The range of the motion sensor is affected by the sensor
orientation and installation height. The sensitivity of the
sensor will also vary due to factors such as the brightness
and temperature changes in the surrounding environment.
In addition, the speed of the person approaching the sensor
will have an effect on when the light will turn on.
Factors that may affect the motion sensor function are:
1. Approach from directly in front of the motion sensor.
2. The temperature difference between the ambient and
human body is small. (For example: high temperature in
summer)
3. Body temperature is not easy to detect. (For example:
wearing heavy clothes)
Replace the battery if the following conditions occur:
● Red indicator keeps flashing
● LED light is bright but dim
● LED light does not light up
● Light-up time becomes shorter
※ When replacing the batteries be certain to replace ALL the batteries
with new batteries.
※ If the lights are placed in an area where they are frequently turned on
and off. The battery life will be shorter than advertised.
※ The motion sensors respond to temperature changes in the sensing area
causing the light to turn on. Therefore pets can activate the lights
which can also have an effect on battery life.
【LIGHTING ZONE SETUP】 【HOW TO SET】
This product uses 2.4 GHz wireless communication
transmission to link each device. The maximum
transmission distance is about 20m (65ft). When the
ambient light is dark, the device that detects the
motion will send a signal to link all other devices
* within 20m (65 ft), if no interference shelter and
* set with the same lighting zone
for activation.
The reason for setting the lighting zone is to avoid
that the lighting area has nothing to do with the
direction of travel, so as to save battery power. This
device can create up to 3 lighting zones. The color of
the setting button can be divided into blue (factory
setting), green and white. Devices set to the same
color can communicate with each other. The lighting
zone set by the user will be retained after the new
battery is replaced- NO need to reset.
※ The wireless transmission distance may be
shortened due to different use environments such as
shelters or building structures.
1. Press the "lighting zone button" on the back of the
device within 3 seconds to change the color of the
"lighting zone indicator".
2. After setting the color, the selected color (light) will be
on for 3 seconds and then flash 3 times, indicating that
the setting is complete.
【INSTALLATION】
Please read the instruction carefully before use, and keep it in a safe place for reference.
※ Do not place any objects between wall lights to avoid interference of wireless transmission.
※ Since the ambient conditions of the mounting area will affect the function of the lights. Check to make sure there are no problems in the mounting area before use.
※ When the backplate cannot be attached to the wall by mounting screws, the supplied double sided tape can be used.
Please note that the mounting surface must be clean and smooth for best results. Do not apply to rough or peeling walls.
※ The double sided tape has a strong adhesive on both sides. It is very easy to damage the wall when the light is removed.
Please use caution during installation and removal as the responsibility for wall damage falls on the installer.
【TROUBLESHOOTING】
There are people in the sensing area of the
light but the light will not turn on.
1. Are the lights installed in a bright area?
2. Are the batteries installed correctly?
3. Is the battery power low?
4. Is the room temperature very low? Or are the
people wearing heavy clothing?
5. Is the person being still and not moving?
1. When the surroundings are bright, the motion sensor is in
sleep mode. Wait until the surroundings become dark or
move to a darker place for inspection.
2. Please confirm that the battery's positive (+) and negative
(-) poles are installed in the correct direction.
3. Replace the battery.
4. The operating principle of the sensor is to respond to
temperature changes caused by the movement of the human
body, so it is not easy to detect temperature differences
under these conditions.
5. If the person in the sensing area is not moving, they will
not be detected by the sensor.
LED Light will not turn off. 1. Is anyone in the sensing area?
2. Is the battery low?
1. Leave the sensing area or keep still.
2. Replace the battery.
There is no one in the sensing area of the
motion sensor, but the light is on.
Is there a heat source or moving objects in the
sensing area?
Remove the heat source or move light also remove any
moving objects in the sensing area.
※ The specifications and appearance of this device may be changed without notice due to improvements.

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC ID: 2AZOB-AP7000RF
Warning: Changes or modifications to this unit not expressly approved by the part esponsible
for compliance could void the user’s authority to operate the equipment