Apollo Smoke Detector XP95 User manual

Thepartnooflhisguideis39214-072/lssue3
Functional Test Data
Output Bit Function Input
Bit Function
2 NOT USED
NOT USED
0 OPERATES RELAY
1
=ON
0 =OFF
2 NOT USED
OPTOINPUT
1 =VOLTAGE ON INPUT
0
=NO INPUT
0 MONITORED INPUT
0 = QUIESCENT
1 = INPUT RECEIVED
Forfurther information on protocol bit usage referto the XP951npuUOutput PIN sheet, PP2017.
Troubleshooting
Before investigating individual units forfaults, it is very importantto check that the system wiring is faultfree.
Earth faults on a data loop or anyancillary zone wiring may cause communication errors.
Many faultconditions are the result ofsimple wiring errors. Check all connections to the unitand make sure
that the correctvalue resistors are fitted where necessary.
Fault finding
Problem Possible Cause
No response or missing Incorrectaddress setting
Incorrectloopwiring
Faultcondition reported Incorrectinputwiring
Relayfailsto operate lncorrectwiring
Control panel has incorrectcause and effectprogramming
Relay energised continuously Incorrectloopwiring
Incorrectaddress setting
Analoguevalue unstable Dual address
Loopdatafault, datacorruption
ConstantAiarm lncorrectwiring
Incorrectend-of-line resistorfitted
Incompatiblecontrol panel software
Apollo Fire Detectors Limited, 36 Brookside R·o~a~d~, jjH~av~a~n-t,~H~a~n~ts~, ~P09 1JR, UK
Tel Fax!"
Email: [email protected] Website: www.apollo-fire.co.uk
XP95 Input/Output Unit
Installation Guide
General
The XP95 lnpuUOutputunit, part no 55000-818, is supplied with a backbox for surface mounting. lt is also
available withouta backbox for flush
fitting- part no 55000-816. Forflush fitting the installerwill need to
provide a suitable metal box with fixing centres of 120.6mm
(UK standard 2-gang accessory box).
Note:
The XP95 Input/Output Unit is not designedfor outdoor use unless it is mounted in a suitable
weatherproofenclosure.
Surface Mounting
1. Mountthe backbox as required and install all cables fortermination. Ensure that earth continuity is
maintained.
2. Remove the cover plate (if secured) from the Input/OutputUnitassembly by inserting the blade of a
terminal screwdriver into each ofthe four securing clips in turn, gently prising the outer edge ofthe cover
plate over the clips underneath. DO NOT USE EXCESSIVE FORCE.
3. Terminate all cables.
4. Gently push the completed assembly towards the back box until the mounting holes are aligned and
secure with the two mounting screws provided. DO
NOT OVERTIGHTEN.
5. Set the address ofthe unit as shown on page 3.
6. Finally, when commissioning is complete, fitthe cover plate by placing it in position, observing the
correct orientation (LEDs on the PCB mustbe aligned with viewing holes). Apply pressure to the cover
plate until all four clips are holding it in position.
Flush Mounting
1. Secure a suitable metal back box (30mm minimum depth) in position and install all cables for
termination. Ensure that earth continuity
is maintained.
2. Follow steps 2 to 6 as above.
TMOM00001790_0001
TMOM00001790/1

Wiring Details
All wiring terminals will acceptsolid or stranded cables up to 2.5mm2
: }L1 (-ve)'
: }L2 (+ve)'
Currrent consumption, loop, max@ 24V
switch-on surge, max 150 ms
quiescent,
20kW EOL fitted
switch inputclosed, max (LED on)
anyothercondition (max 2 LEDs on)
3.5mA
1.2mA
6mA
4.5mA
0
Fora full technical specification ofthe InpuUOutput Unit, please referto the XP95 InpuUOutputUnit
PIN Sheet, PP 2017.
Address Setting
The address ofthe Input/OutputUnit is set using the lowerseven segments ofthe OIL switch. Each
segment ofthe switch must be set to "0" (ON) or "1" (OFF), using a small screwdriver or similar tool. A
complete list ofaddress settings is shown below.
DIL switch DIL switch DIL switch DIL switch DIL switch
addr selling addr selling addr selling addr selling addr selling
1234567 1234567 1234567 1234567 1234567
1000000 11 1101000 21 1010100 31 1111100 41 1001010
0100000
12 0011000 22 0110100 32 0000010 42 0101010
1100000
13 1011000 23 1110100 33 1000010 43 1101010
0010000
14 0111000 24 0001100 34 0100010 44 0011010
1010000 15 1111000 25 1001100
35 1100010 45 1011010
6 0110000 16 0000100 26 0101100 36 0010010 46 0111010
7 1110000 17 1000100 27 1101100 37 1010010 47 1111010
8 0001000 18 0100100 28 0011100 38 0110010 48 0000110
9 1001000 19 1100100 29 1011100 39 1110010 49 1000110
10 0101000 20 0010100 30 0111100
40 0001010 50 0100110
51 1100110 61 1011110 71 1110001 81 1000101 91 1101101
52 0010110 62 0111110 72 0001001 82 0100101 92 0011101
53 1010110 63 1111110 73 1001001 83 1100101 93 1011101
54 0110110 64 0000001 74 0101001 84 0010101 94 0111101
55 1110110 65 1000001 75 1101001 85 1010101 95 1111101
56 0001110 66 0100001 76 0011001 86 0110101
96 0000011
57 1001110 67 1100001 77 1011001 87 1110101 97 1000011
58 0101110 68 0010001 78 0111001 88 0001101 98 0100011
59 1101110 69 1010001 79 1111001 89 1001101 99 1100011
60 0011110 70 0110001 80 0000101
90 0101101 100 0010011
101 1010011
111 1111011 121 1001111
102 0110011 112 0000111 122 0101111
103 1110011 113 1000111 123 1101111
104 0001011 114 0100111 124 0011111
105 1001011 115 1100111 125 1011111
106 0101011 116 0010111 126 0111111
107 1101011 117 1010111
108 0011011 118 0110111
109 1011011 119 1110111
110 0111011 120 0001111
Commissioning
lt is importantthatthe XP951npuUOutput Unit be fully tested after installation. An XP95 Test Set, part no
55000-870, may be used to carry outfunctional testing of individual units. ltcan also be used to perform
data integrity tests
of an entire system.
LED Indicators
0 Relay On Illuminated red when relay is energised
0 Switch Closed Illuminated red when monitored field contact is activated
0 Fault Illuminated yellowwhen input is open or shortcircuit
The use ofthe LEDs can be inhibited by setting the 'LED ENABLE' segment ofthe DIL switch to '0'
TMOM00001790_0002
TMOM00001790/2