Aquaglide Platinum METRO 3 User manual

Stop! Read this manual carefully before using this product!
North Sports, Inc. #1 North Shore Dr, SE White Salmon, WA 98672 TEL: [phone] FAX: [phone]
THE WARNINGS AND PRACTICES SET FORTH ABOVE IN THE WATER-
SPORTS SAFETY CODE REPRESENT SOME COMMON RISKS ENCOUN-
TERED BY USERS. THE CODE DOES NOT PURPORT TO COVER ALL
INSTANCES OF RISK OR DANGER. PLEASE USE COMMON SENSE AND
GOOD JUDGMENT.
Your equipment :
• Check all equipment prior to use. Inspect your product for missing, defective or
worn parts.
• Always check for proper ination before each use. Temperature and environ-
mental changes can cause changes in tube pressure. Using the product over or
under inated is dangerous and can cause damage to the product, voiding the
warranty.
• Always wear a life vest (PFD) as required by the authorities in area of use.
Please contact us if you have any questions on the proper selection,
function, or safe use of this product.
Contents: (1) METRO Tube, (1) Repair Kit
Please Do Not Return This Product To The Store!
For questions regarding assembly, parts, or warranty, contact our
customer service department directly at 1-509-493-4938 or access
product information at the website below.
Watersports Safety Code
Watersports are fun and challenging but involve inherent risks of
injury or death. To increase your enjoyment of the sport and to
reduce your risks, use common sense and follow these rules:
Before you start:
• Familiarize yourself with all applicable federal, state, and local laws, the risks
inherent in the sport, and the proper use of the equipment.
• Know the waterways.
• Use caution and common sense.
• Do not use in swimming pools, or within 4,5m (15ft.) of boats, docks, or other
hard obstructions.
• Do not attempt or allow somersaults. Landing on the head or neck can cause
serious injury, paralysis or death.
• Do not dive head rst or swim under this product.
• Never use at night, or in low-light conditions.
• Never use in poor weather conditions with excessive wind, waves or lightning.
• Do not use on dry land.
• Only allow use of the product with proper supervision. Secure the product
when not in use to prevent access by any other users.
• Do not jump or dive from this item.
• Do not jump onto this item from any other item.
• Do not use in water where there are sharks or other animals that could pose a
threat to humans.
• Always remove personal items such as rings, watches or other sharp objects
before use.
It is the owner’s responsibility to read the owner’s manual and instruct
all users in the safe operation of these products. By inating these products you hereby
agree to the Release of Liability, Claim Waiver, and Assumption of Risk Agreement in
this manual. Please read this manual prior to inating and using these products and
keep for future reference. As with any action sport, recklessness, inexperience, misuse,
or neglect of the equipment may result in serious injury or death.
Owner’s Manual
www.Aquaglide.net
Manual Covers the
following towables
METRO 3
METRO 5
METRO 6
Maximum
Riders
Three (3)
Five (5)
Six (6)
Rope
Strength
3,350 lbs (14,9kN)
7,000 lbs (31,1kN)
8,000 lbs (35,6kN)
*METRO 6 shown. Size may vary
depending on the item purchased.

For more information go to:
www.Aquaglide.net
Aquaglide Inc. #1 North Shore Dr, SE White Salmon, WA 98672 TEL: [phone] FAX: [phone]
Assembly
1) Locate a at, dry area with access to electrical outlet or extension cord. The best
setup position will also make launching easy, so ideally the METRO tube should
be carefully carried into position at the water’s edge. NOTE: Dragging or sliding the
METRO over ground either before or after ination can cause damage.
2) Once in the setup/ launch position, unfold the METRO Tube completely and locate
the Main Valve, centered on the back of the largest, white tube.
3) Using a high output pump, place the ination hose with proper adaptor into the
valve and inate Main Tube. Inate to 1.2 psi (0,083 bar). Check for proper air
pressure using a manometer. After ination, replace Main valve cover. Ination
times can vary by inator, but the METRO should be rm and tight when completely
inated. DO NOT OVER-FILL. Excessively high pressure can cause damage to
the product and may void the warranty. In hot weather, be sure to leave room for air
expansion.
WARNING: Do not use an air compressor to inate tube. Air compressors are
designed for high pressure ination and can cause tube to burst if over-inated.
4) Once the Main tube is properly inated, next locate the valves on the blue
Stabilizer Tubes. METRO 5 and 6-Person models have 2 stabilizer tubes on each
side. METRO 3 has 1 Stabilizer tube on each side of the Main Tube. Inate EACH
Stabilizer tube to 1.2 psi (0,083 bar) until all tubes have been inated. Check for
proper air pressure using a manometer. After ination, replace the valve covers.
6) Inspect and conrm towing bridle and towing ring before use. Connect tow line
(not provided) to towing ring using a professionally eye-spliced end. Use ONLY high
quality rope that meets the required break strength requirement for the number of
riders as shown in this Owner’s Manual. Inspect and conrm tow rope and its con-
nection to the towing ring to ensure rider and operator safety. IMPORTANT: These
areas are under high load and are subject to wear. Repeat this process before
every use.
7) To launch the product, make sure to have at least 2 people evenly spaced around
the product to help carry it. NEVER DRAG THE METRO! YOU MUST LIFT AND
SET TO AVOID ANY ACCIDENTAL TEARING AND/OR ABRASION.
Towing
1) This item is an action towable for water use. When towing behind a powerboat,
users assume a sitting position on top of the center tube, facing the front of the item
with both hands rmly grasping the handle.
2) While the METRO tube is large, it is also very buoyant, resulting in a a tube
that can easily be pulled by most capable tow boats including full-sized personal
watercraft. However, because of the high loads that can be generated, it is important
to conrm that your tow rope and tow ttings are up to the task.
3) Before each use always inspect the product carefully and conrm:
A. Proper ination - 1.2 psi (0,083 bar) ALL tubes.
B. Secure connections linking the Main Tube and towing bridle,
C. Secure connections linking the Tow Ring and Tow Rope,
D Secure connections linking the Tow Rope and Tow Boat, and nally
E. No signs of wear in any of these load-bearing areas.
*NOTE: Immediately replace any parts that show signs of wear.
4) When towing the METRO, take care to position riders so as to balance weight
evenly. When fully loaded, heavier riders should sit toward the back of the product
to avoid ‘plowing’ of the tube at low speeds.
5) When towing the METRO, the driver should never exceed 18 mph (29 km/h)
with adults, or 15 mph (24 km/h) with children. The driver should avoid exces-
sive speed and sharp turns. Do not tow in excessive chop or waves which could
cause the tube to become airborne or unstable. The driver must use common
sense to avoid potentially dangerous situations. Under normal conditions, the
METRO is both exciting and extremely stable.
6) When towing the METRO, riders should remain seated with both hands rmly
grasping handles at all times. Do not allow riders to touch the water with hands or
feet while in motion. Never jump or dive from the product while in motion.
Anchoring
IMPORTANT: If you will use the METRO in an anchored setting, proper anchoring
is essential to the safety of your product. Due to the wide variety of conditions, we
advise using a professional skilled in mooring and anchoring, and experienced
with local conditions. If improperly anchored, the product can move and/or oat
away. Aquaglide, Inc. is not responsible for any damage, injuries or losses due to
improper anchoring.
Here are some general guidelines for anchoring your product. These guidelines
are not intended to replace the need for professional installation.
1) Choose your location for your METRO. Place the product in at least 8 ft.
(2,44 m) of water depth and in an area protected from the wind and boat trafc.
Review your lake rules and restrictions with your local authorities.
2) Carefully check area under the product for sharp or dangerous objects (i.e.
rocks or stumps).
3) Keep a safe distance from docks, boats, boat lifts, and any other structures.
4) Anchors and anchor line are sold separately. We recommend at least 100 lbs.
of weight for the METRO. Heavier anchors (200 lbs. or more) should be used on
large, windy bodies of water.
5) If the METRO is anchored, securely connect the anchor line to the Tow Ring
and tow bridle.
6 Leave sufcient slack in the anchor line to allow the METRO movement in wind,
waves or tides without displacing your anchor.
7) If severe weather is expected, it is best to remove the METRO from the water
and secure or store it.
Care and Maintenance
1) While your product has been initially treated with UV protectant, long-term
exposure to sunlight will damage the product. Regularly apply a UV protectant to
the exposed surface of the tube to ensure the life of your product. We recommend
using ONLY 303 UV Protectant intended for use on vinyl for this purpose. Monthly
application while the product is in use is required. NOT DOING THIS WILL
VOID THE WARRANTY. 303 UV Protectant is available at most watersports
dealers, or online at www.303-products.com.
2) WARNING: Certain products, especially petrolium-based solvents, clean-
ers and protectants such as ArmorAll can damage the product and use of these
products will void the warranty.
3) WARNING: Use of a high-pressure washer will damage the product and
void the warranty. To clean, use a soft bristle brush with mild soap and fresh water.
303 UV Protectant contains a ‘safe for vinyl’ cleaner, and can be used to clean and
protect the product at the same time.
4) Check the ination of your tube often. Check for proper air pressure using a
manometer. It may appear to have lost air early in the morning, but will expand
once the sun warms it. Maximum expansion will occur in the heat of the day.
Proper ination is critical to the safe operation of your product and will prolong
damage from wear.
Storage
1) Before storing, place the product on a clean, level area. Clean with mild soap
and water and allow to dry completely. Apply 303 Protectant to the surface of all
tubes before deating.
2) Remove ALL of the air from the tubes using the deation end of the high output
inator/deator. If some air is left in the tube, it may freeze causing cracking. Close
valve and seal with valve cap immediately to prevent air from leaking back into
tube.
3) Lay the product out at and fold in thirds, bringing the Stabilizer tubes over the
Main tube, and leaving a long narrow strip. Next, fold or roll the tube from the front
toward the back. Allow any trapped air to escape while folding. Make sure to re-
seal each tube once complete.
4) Store the METRO out of direct sunlight and protected from the environment in a
clean, dry location. It is best to store inside a container with moth balls to prevent
damage from rodents. NEVER store uncovered, in a damp location, or on a
concrete surface! NEVER store at temperatures below 40 degrees F.
Aquaglide, Inc. #1 North Shore Dr, SE White Salmon, WA 98672 TEL: [phone] FAX: [phone]
www.Aquaglide.net
Watersports can be safe and fun for all levels of enthusiasts. The Operator’s Manual is presented to enhance
your enjoyment of the sport. It is intended to alert you to some of the potentially dangerous conditions that
can arise in all watersports. It is the owner’s responsibility to read the owner’s manual and instruct all users
in the safe operation of these products. By inating these products you hereby agree to the Release of
Liability, Claim Waiver, and Assumption of Risk Agreement in the Owner’s Manual.
To reduce the risk of injury or death, follow these guidelines:
• Carefully read the product Owner’s Manual and follow the instructions.
• Take all reasonable precautions in the use and operation of your trampoline and/or aquapark.
• Teach anyone using your trampoline and/or aquapark about safe guidelines prior to use.
• Know your own limits. Stop when you are tired. Act responsibly. Be in good physical
condition and be cautious in your use of this or any other water sports product.
• Periodically check mooring bridles and/or lines to ensure safety. Replace any portion of
mooring and/or connection system that shows signs of wear.
• Do not add any hardware or attachments not otherwise supplied by the manufacturer.
THE WARNINGS AND PRACTICES SET FORTH ABOVE REPRESENT SOME COMMON RISKS
ENCOUNTERED BY USERS AND DOES NOT PURPORT TO COVER ALL INSTANCES OF RISK OR DANGER.
PLEASE USE COMMON SENSE AND GOOD JUDGMENT.
Please contact the dealer or manufacturer of this product if you have any questions about proper selection,
function, or safe use of this product. Made in China
CAUTION
Stabilizer
Tube Valves
Main Valve
METRO Diagram
(front)
Owner’s Manual
*METRO 6 shown. Size may vary
depending on the item purchased.
(front)
Towing Bridle

By opening and assembling this product, you are agreeing (1) to be bound to the terms set forth below and (2) to require anyone using this
product to be bound by such terms. If you are unwilling to be bound by these terms, return this product (before use) for a full refund.
ASSUMPTION OF RISK : Use of this product and any of its components involves certain inherent risks, dangers, and hazards which can result in serious personal injury and
death. In using the product, you freely agree to assume and accept any and all known and unknown risks of injury while using this equipment. The risks inherent in the sport
can be greatly reduced by abiding by the Warning Guidelines listed in this Owner’s Manual and by using common sense.
RELEASE AND WAIVER OF CLAIMS AGREEMENT: In consideration of the sale of the product to you, you hereby agree to the fullest extent permitted by law as follows:
TO WAIVE ANY AND ALL CLAIMS that you have or may in the future have against North Sports Inc., and Aquaglide Inc.,its distributors and dealers, resulting from use of
this product and any of its components.
TO RELEASE North Sports, Inc. and Aquaglide, Inc. from any and all liability for any loss, damage, injury, or expense that you or any users of this product may suffer, or that
your next of kin may suffer, as a result of the use of this product, due to any cause whatsoever, including negligence or breach of contract on the part of North Sports Inc. and
Aquaglide Inc. in the design or manufacture of this product and any of its components.
ARBITRATION: In further consideration of the sale to you of this product and any of its components, you hereby agree to submit to binding arbitration any and all claims which
you believe you may have against North Sports Inc. and Aquaglide Inc. arising from the use of any North Sports Inc. and Aquaglide Inc. equipment or products. The arbitration
shall be pursuant to the rules of the American Arbitration Association. Arbitration shall be commenced within (1) year from the date on which any alleged claim rst arose.
Further, the arbitration shall be held in White Salmon, Washington unless otherwise mutually agreed to by all parties. The submission to the American Arbitration Association
shall be unlimited and the arbitration award may be enforced by any Court of competent jurisdiction.
BINDING EFFECT OF AGREEMENT : In the event of your death or incapacity, this Agreement shall be effective and binding upon your heirs, next of kin, executors, adminis-
trators, assigns, and representatives.
ENTIRE AGREEMENT : In entering into this Agreement, you are not relying upon any oral or written representations other than what is set forth in this agreement and the
North Sports Inc. and Aquaglide Inc. Owner’s Manual.
NOTICE! - Release of Liability, Claim Waiver, and Assumption of Risk Agreement
of the package or it will not be accepted at our
warehouse. Freight on the returned product must
be prepaid or it will not be accepted. Upon receipt,
Aquaglide will make a determination within (30)
days. If the product is covered under warranty it
will be returned to the customer at the expense of
Aquaglide, Inc. after repairs can be made. If not,
the customer will receive a quote for repair and/
or replacement as well as any necessary cleaning
and shipping charges. The customer will have
30 days to accept the quotation. At the end of 30
days, or upon refusal of the quote, Aquaglide will
return the product in the condition in which it was
received at the customer’s expense. The customer
agrees to authorize Aquaglide, Inc. to charge the
customer’s credit card for any costs not covered
under the terms and conditions of the Aquaglide
Warranty.
Serial Number
All Aquaglide Platinum products are marked with
a serial number near the main ination valve (#1).
The serial number may be stamped into the PVC
directly around the valve, or it may be visible on
a welded plate near the valve. Please include
this number when you contact Aquaglide, or your
dealer, with any warranty claim.
Aquaglide, Inc. #1 North Shore Dr, SE White Salmon, WA 98672 TEL: [phone] FAX: [phone]
www.Aquaglide.net
Aquaglide, Inc. warrants products to be free
of defects in material or workmanship to
the original purchaser for a period of One (1)
year from date of purchase. This warranty is
subject to the following limitations:
1. Warranty is valid only with dated proof of pur-
chase in the form of the original invoice.
2. Warranty is valid when the product is used for
either recreational activities, or commercial use.
3. Aquaglide will make the nal warranty determi-
nation which may require inspection and/or photos
of the product which clearly show defect(s). We
require the above be sent to another location of our
choice, freight prepaid, or by email to warranty@
aquaglide.net.
4. If a product is deemed to be defective by Aqua-
glide, the warranty covers the repair or replacement
of the defective product only. Aquaglide will not
be responsible for any costs, losses, or damages
incurred as a result of loss of use of product.
5. This warranty does not cover damage caused
by misuse, abuse, neglect, or normal wear and
tear, including, but not limited to, punctures,
dragging the product over the ground, damage
due to excessive sun exposure or seam failure
due to overination in the sun, damage caused by
improper handling and storage, damage caused by
use in waves or shore break, and damage caused
by anything other than defects in materials and
workmanship.
6. This warranty is voided if any unauthorized
repair, change, or modication has been made to
any part of the equipment. Authorization for such
must come in writing from Aquaglide.
7. The warranty for any repaired or replacement
equipment is good from the date of the original
purchase only.
8. Any warranty claims must be accompanied
by the original purchase receipt. The name of the
retailer and date of purchase must be clear and
legible.
9. There are no warranties which extend beyond
the warranty specied here.
Returns and Service Policy
Product can be returned only if a return autho-
rization number (RA) is given by Aquaglide in
advance. The RA number must be on the outside
Warranty