Aqualux Aql-155 Installation guide

Installation & Care Instructions

AQL-155

1300 662 644

sales@aqualux.com.au

Visit www.aqualux.com.au for: Full product details and available options.Full product details and available options.

Order code conguration & customised datasheets. Voltage drop calculator & LED technical information.Order code conguration & customised datasheets. Voltage drop calculator & LED technical information.

--Thank for purchasing an Aqualux Lighting product.Thank for purchasing an Aqualux Lighting product.

--Please follow these instructions carefully.Please follow these instructions carefully.

--Your warranty and safety depends on it.Your warranty and safety depends on it.

--All wiring must be in accordance with local regulations.All wiring must be in accordance with local regulations.

--If a fault or failure occurs, please contact Aqualux toIf a fault or failure occurs, please contact Aqualux to

arrange servicing.arrange servicing.

--It is recommended to wash the luminaire with fresh water fromIt is recommended to wash the luminaire with fresh water from

time to time to stop salt and corrosive elements building up.time to time to stop salt and corrosive elements building up.

--Do not attempt to service the product.Do not attempt to service the product.

56mm

PaverPaver

84mm Mono

102mm RGBW

56mm

onduit recommended

Allow adequate space

between Fitting and

Conduit for Connectors

56mm

84mm Mono

102mm RGBW

56mm

onduit recommended

Allow adequate space

between Fitting and

Conduit for Connectors

84mm Mono

102mm RGBW

Use silicone sealant under dressUse silicone sealant under dress

ring for rm hold on paver.ring for rm hold on paver.

1.1.

1. Illustration depicts AqualuxPlus cable connectors. AQL-155 and AQL-530 only.1. Illustration depicts AqualuxPlus cable connectors. AQL-155 and AQL-530 only.

1.1. 1.1.

Drill at least 125mm depth and 56mmDrill at least 125mm depth and 56mm

diameter hole. Use AQP-09-0016.diameter hole. Use AQP-09-0016.

Use silicone sealant under dressUse silicone sealant under dress

ring for rm hold on concrete.ring for rm hold on concrete.

Use silicone sealant under dressUse silicone sealant under dress

ring for rm hold on timber deck.ring for rm hold on timber deck.

Drill at least 125mm depth and 56mmDrill at least 125mm depth and 56mm

diameter hole. Use AQP-09-0016.diameter hole. Use AQP-09-0016.

56mm diameter hole. Allow at least 85mm56mm diameter hole. Allow at least 85mm

depth required for light tting and cabledepth required for light tting and cable

connections. No sleeve required.connections. No sleeve required.

Set light tting into paverSet light tting into paver

PaversPavers

AQP-09-0016 recommendedAQP-09-0016 recommended

Formed concrete pour,Formed concrete pour,

set and x PVC sleeve AQP-09-0016set and x PVC sleeve AQP-09-0016

recommendedrecommended

Timber deckingTimber decking

Set light tting into concreteSet light tting into concrete Set light tting onto deckSet light tting onto deck

1111

3333

AQL-155 /AQL-155 / 24V AC / DC24V AC / DC IP67IP67

YOUR WARRANTY RELIES ON CORRECT INSTALLATION & CARE.

Check product label for correct power requirements.

Do not connect to mains (240V).

Do not “hot-plug” lighting xture - i.e. do not connect to energised power supply.

Ensure cable termination is fully sealed and all joins are heat-shrinked or encapsulated.

Ensure cable glands are hand tightened and end caps secured after transit & installation.

Do not attempt to eld service Aqualux ttings without prior instruction.

Do not look directly at LED light source - it will damage your eyes!

For surface mount, a bead of silicone between surface and tting is recommended.

These notes must be observed for the Aqualux Warranty to apply.

Wiring and AqualuxPlus Connect Instructions

AQL-155

1300 662 644

sales@aqualux.com.au

Visit www.aqualux.com.au for: Full product details and available options.Full product details and available options.

--A waterproof connection must be made using a heavyA waterproof connection must be made using a heavy

walled adhesive lined heat shrink, between the supply cablewalled adhesive lined heat shrink, between the supply cable

and the tting.and the tting.

--Note: These instructions must not contravene your localNote: These instructions must not contravene your local

electrical authority regulations, with which all installationselectrical authority regulations, with which all installations

here in must comply.here in must comply.

IfIf your tting has AqualuxPlus connectors, do not removeyour tting has AqualuxPlus connectors, do not remove

them. This will void your warranty.them. This will void your warranty.

Male connector is attached to light tting.Male connector is attached to light tting.

Female connector can be sent to project ahead of time forFemale connector can be sent to project ahead of time for

pre-installation.pre-installation.

RGBW WiringRGBW Wiring Mono WiringMono Wiring

24V DC Power

(

)

24V

(+)

24V

240V In

RED

GREEN

BLUE

WHITE

(-) BLUE

(+) BROWN

RED

GREEN

BLUE

WHITE

RGBW - Light Fitting

RGBW

Control Unit

24V AC / DC Power

240V In

GREEN

(-) WHITE

(+) RED

Mono

Light Fitting

GREEN

(-) WHITE

(+) RED

Mono

Light Fitting

GREEN

(-) WHITE

(+) RED

Mono

Light Fitting

M12 6-pin (RGBW) AqualuxPlus ConnectorsM12 6-pin (RGBW) AqualuxPlus Connectors

What is AqualuxPlus Connector?What is AqualuxPlus Connector? The M8 and M12 AqualuxPlus IP67 Connectors have been designed to address two key issues facingThe M8 and M12 AqualuxPlus IP67 Connectors have been designed to address two key issues facing

LED lighting system installations. 1. Water siphoning - minimises the chance of water ingress via cable. 2. Serviceability - quick removal ofLED lighting system installations. 1. Water siphoning - minimises the chance of water ingress via cable. 2. Serviceability - quick removal of

tting for servicing.tting for servicing. Note:Note: It is essential to ensure an IP rated seal at the connection point of the main trunk line with resin lined heatshrinkIt is essential to ensure an IP rated seal at the connection point of the main trunk line with resin lined heatshrink