Arestech TPM-3624PW User manual

User Manual
User Manual
TPM-3624PW
IP66/69K Protected 23.8" Stainless Steel Industrial Monitor
with P-Cap Touch screen

User Manual
Record of Revision
Version
Issued Date
Description
Owner
V1.0
2018/12/6
First Release
Jacky

User Manual
Copyright
The documentation and the software included with this product are copyrighted 2014
by Arestech Co., Ltd. All rights are reserved. Arestech Co., Ltd. reserves the right to
make improvements in the products described inthis manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmitted in any
form or by any means without the prior written permission of Arestech Co., Ltd.
Information provided in this manual is intended to be accurate and reliable. However,
Arestech Co., Ltd. assumes no responsibility for its use, nor for any infringements of
the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty
Arestech warrants to you, the original purchaser, that each of its products will be free
from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Arestech, or which have been
subject to misuse, abuse, accident or improper installation. Arestech assumes no
liability under the terms of this warranty as a consequence of such events. Because of
Arestech’s high quality-control standards and rigorous testing, most of our customers
never need to use our repair service. If an Arestech product is defective, it will be
repaired or replaced at no charge during the warranty period. For outof- warranty
repairs, you will be billed according to the cost of replacement materials, service time
and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Arestech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.

User Manual
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth.
Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened
only by qualified service personnel.
If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.

User Manual
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
14. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE
THESTORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE
60° C(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
15. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive
electronic components.

User Manual
Contents
Chapter 1: General Introduction..................................................................................1
1.1 I/O Arrangement........................................................................1
1.2 OSD Key Use instructions..........................................................4
1.3 Mechanical Dimension................................................................7
Chapter 2: VESA Mounting..................................................................................9
2.1 VESA Mounting.................................................................. ..........9
Chapter3. System Setup...........................................................................10
3.1 Power Installation Procedure................................................................10
1 Main Menu......................................... ..................................17
3.2 Advanced Menu..........................................................................18
3.3 Chipset Menu...........................................................................28
3.4 Security Menu.............................................................................32
3.5 Boot Menu.............................................................................34
3.6 Exit Menu............................................................................

User Manual
Page 1
Chapter1. General Introduction
1.1 I/O Arrangement
VGA M12 Port Female 12pin
Pin
Definition
Pin
Definition
1
Red
2
Red GND
3
Green
4
Green GND
5
Blue
6
Blue GND
7
GND
8
GND
9
SDA
10
HSync
11
VSync
12
SCL
M12 USB
Touch
Waterproof
HDMI (Option)
M12 VGA
M12 12-24V DC
Jack
waterproof
Touch On/Off
Botton

User Manual
Page 2
M12 USB Port Male 5pin
* Only Touch control Use
M12 12/24V DC In Female 5pin
Pin
Definition
1
VCC
2
VCC
3
GND
4
GND
Pin
Definition
1
+5
2
D-
3
D+
4
GND
5
SHILDING

User Manual
Page 3
Touch On/Off Button
LIGHT
Stauts
Green
ON ->ACTIVE
No light
OFF->NO ACTIVE
Waterproof HDMI (Option)
Pin
Definition
Pin
Definition
1
TMDS Data2+
2
TMDS Data2 Shield
3
TMDS Data2 -
4
TMDS Data1+
5
TMDS Data1 Shield
6
TMDS Data1-
7
TMDS Data0+
8
TMDS Data0 Shield
9
TMDS Data0-
10
TMDS Clock+
11
TMDS Clock Shield
12
TMDS Clock-
13
Reserved
14
Reserved
15
SCL
16
SDA
17
DDCGround
18
+5 V Power
19
Hot Plug Detect

User Manual
Page 4
1.2OSD Key Use instructions
Power Key: LCD power key
LED lights: two-color LED (ON->Green/OFF-->Red)
Key: increase the brightness of the keys; Menu key for Up
Key: decrease the brightness keys; Menu key for Down
Menu / Select: Menu key to open, which is open after the Menu selection key
Auto / Exit: Auto Adjust picture correction; Menu key for Exit
INDEX LED lights:(Option)
FN:Function Key(Option)
AUTO
Down
Power
UP
LED
MENU

User Manual
Page 5
OSD Menu Description
Function Menu
Color Adjustment
Contrast
0~100
Brightness
0~100
ColorAdjustment
Red (0~100)
Green (0~100)
Blue (0~100
Color Temperature
9300K 6500K User
Image Adjustment
Clock
Phase
Sharpness
0~100
horizontal position
0~100
Vertical Position
0~100
OSD Menu
OSD Horizontal Pos
0~100
OSD Vertical Pos
0~100
OSD Timer
0~100
Language
English
Francais
Deutsch
Espanol
繁體中文
簡体中文
日本語

User Manual
Page 6
Singnal Source
D-SUB
HDMI
Display Port
Auto Search
Audio
Volume
0~255
(Recommended to
150 )
Mute

User Manual
Page 7
1.3 Mechanical Dimension

User Manual
Page 8

User Manual
Page 9
Chapter 2. VESA / Panel Mounting
2.1 VESA Mounting
Step1. Check the VASA mount dimension on the back cover .
There are two choice : 100 x 100mm
Step2. Fasten the four screws to bond monitor to VESA Stand
Warning !
1. The length of VESA mount screw cannot exceed 5mm.
(Calculated from monitor's back cover)
2. Any wrong installation will cause monitor's great .
The Spec of
1. Screw Length Limitation: 5mm
(Calculated from monitor's back cover)
2. Screw Spec Limitation: M4 size

User Manual
Page 10
Chapter3. System Setup
3.1 Power Installation Procedure
Step 1. Connect the Power M12 Connector and tighten in a clockwise direction
AC to DC power adaptor specification
1. Input support voltage: 110V ~ 240V AC power , 50~60Hz
2. Output support voltage: 12V DC power @5A MAX
3. 0~40 degree C operating temperature

User Manual
Page 11
7F., No.94, Xiwei St., Sanchong Dist., New Taipei City
241, Taiwan (R.O.C.)
Tel : [phone]
Fax : [phone]
www.arestech.com.tw