Aruba LS-BT1-MNT-50 User manual

Aruba LS-BT1-MNT-50
Installation Guide
0511745-01 |December 2014 1
This document provides installation instructions for mounting the LS-BT1 location beacon in an
indoor environment using the LS-BT1-MNT-50 accessory kit.
The LS-BT1 location beacon is referred to as device in rest of the document.
Package Contents
50 sets of mounting bracket and adhesive pad (one set per device)
Installation guide (this document, printed)
Installing the Device using the Adhesive Pad
This mounting option allow mounting the device on a flat surface using an adhesive pad.
Required Tools and Equipment
The following tools and equipment are required for installing the device:
An adhesive pad (included in the package)
Prerequisites
Before installing the device, ensure that the following surfaces are clean and dust-free.
the mounting surface
the grooves for adhesive pads on the bottom of the device
It is recommended to clean these surfaces using a solvent with 50/50 isopropyl alcohol/ water
mixture.
Installation Steps
To install the device using an adhesive pad:
1. Attach the adhesive pad on the grooved area on the back of the mounting bracket, as shown in
Figure 1.
Figure 1 Attaching the Adhesive Pad to the Mounting Bracket
.

2Aruba LS-BT1-MNT-50 | Installation Guide
2. Remove the protective film on the adhesive, attach the mounting bracket on the surface in the
upright position, as shown in Figure 2.
Figure 2 Removing the Protective Film
3. Align the keyhole slots on the device with the projections on the mounting bracket, as shown in
Figure 3.
Figure 3 Aligning the Device with the Bracket
4. Slide the device down until the clip of the mounting bracket snaps onto the top of the device, as
shown in Figure 4.
Figure 4 Attaching the Device on the Mounting Bracket
Ensure that the device is activated before attaching it on the mounting bracket.

Aruba LS-BT1-MNT-50 | Installation Guide 3
Installing the Device using Screws
This mounting option allows mounting the device on a flat surface using screws.
Required Tools and Equipment
The following tools and equipment are required for installing the device:
One mounting bracket
Two M3 flat head screws (not included in the package)
Suitable screwdriver (not included in the package)
Installation Steps
To install the device using screws:
1. Choose a flat surface for the mounting bracket.
2. Secure the mounting bracket in the upright position on the surface using two M3 flat head screws,
as shown in Figure 5.
Figure 5 Securing the Mounting Bracket on a Flat Surface
3. Align the keyhole slots on the device with the projections on the mounting bracket, as shown in
Figure 6.
Figure 6 Aligning the Device with the Mounting Bracket
4. Slide the device down until the clip of the mounting bracket snaps onto the top of the device, as
shown in Figure 4.
Ensure that the device is activated before attaching it on the mounting bracket.

© 2014 Aruba Networks, Inc. All rights reserved.
www.arubanetworks.com
1344 Crossman Avenue
Sunnyvale, California 94089
Phone: [phone]
Fax [phone]
4Aruba LS-BT1-MNT-50 | Installation Guide
Contacting Support
Table 1 Contact Information
Main Site arubanetworks.com
Support Site support.arubanetworks.com
Airheads Social Forums and Knowledge
Base
community.arubanetworks.com
North American Telephone [phone] (Toll Free)
1-408-754-1200
International Telephones http://www.arubanetworks.com/support-services/support-program/
contact-support
Software Licensing Site licensing.arubanetworks.com
End of Support information http://www.arubanetworks.com/support-services/end-of-life-
products/end-of-life-policy/
Security Incident Response Team (SIRT) http://www.arubanetworks.com/support-services/security-bulletins/
Support Email Addresses
Americas, APAC, and EMEA [email protected]
Security Incident Response Team (SIRT) [email protected]