Ascot 302-63220 User manual

OPERATING MANUAL
ASCOT SUPPLY
Safety Pin Style
22-Ton Jack Stands
MAKE SURE TO READ AND FULLY UNDERSTAND THE INSTRUCTION MANUAL BEFORE USING THIS PRODUCT
Model No. Capacity Base Size Min. Height Max Height
302-63220 22 Ton 9-7/8” x 9-7/8” 13-3/8” 19-5/8”
This is the safety notification symbol.
This symbol will notify you of any
potential injury hazards. Please follow
all instructions that follow this symbol
to avoid possible injuries or death.
Indicates a hazardous situation.
If proper steps are not followed,
death or serious injury could result.
WARNING

1
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
Before using these jack stands, be sure to read all content within this manual, ensuring that you understand the
operating procedures, maintenance requirements and all safety warnings.
The owner and/or operator shall have an understanding of the product, its operating characteristics, and safety
operating instructions before operating this device. Safety information shall be emphasized and understood.
If the operator is not fluent in English, the product and safety instructions shall be read to and discussed with
the operator in the operator’s native language by the purchaser/owner or his designee, making sure that the
operator comprehends their contents.
ACTIONS TO HELP PREVENT DANGEROUS SITUATIONS
• Study, understand and follow all instructions before operating this device.
• Maximum load capacity per matched pair shall not exceed the rated capacity of the individualstand.
• Use only on hard, level surfaces.
• No alterations shall be made to this product.
• Stands are not to be used to simultaneously support both ends of a vehicle.
• Use as a matched pair only
• Use stands to support one end of a vehicle only.
• Center load on saddle.
• Failure to heed these warnings may result in serious personal injury and/or property damage.
INSPECTION
• This device shall be inspected immediately if the device is believed to have been subjected to anabnormal load
or shock. It is recommended that this inspection be made by a manufacturer’s orsupplier’s authorized repair
facility.
• Owners and/or operators should be aware that repair of this equipment may require specializedknowledge
and facilities. It is recommended that an annual inspection of the product be madeby a manufacturer’s or
supplier’s authorized repair facility and that any defective parts, decals,or safety labels or signs be replaced
with manufacturer’s or supplier’s specified parts.
DAMAGED EQUIPMENT AND ADD-ONS
Any jack stand that appears to be damaged, is found to be worn or operates abnormally in any way will be
removed from service and destroyed immediately.
Alterations
Because of potential hazards associated with this type of equipment, no alterations shall be made to the
product.
Attachments and Adapters
Only attachments and/or adapters supplied by the manufacturer shall be used.
WARNING

SETUP
• Prior to each use, visual inspection (See Pg.2 ) shall be made to the device by checking for abnormal
conditions, such as cracked welds, damaged, loose or missing parts.
• Consult the vehicle owner’s manual to determine the location of support points.
• Be sure to set the vehicle in park with the emergency brake on and wheels securely chocked.
• Be sure that the vehicle and the jack stands are on a hard, level surface.
ASSEMBLY
• Insert extension column into base collar.
OPERATION
Supporting a Load
• Properly chock the vehicle wheels.
• Lift the extension column up to desired position, insert support rod through the column adjustment holes. Ensure the
support rod is properly and fully engaged in the column holes and securely rested on the collar.
• Slowly and carefully lower the vehicle onto the saddle. Be sure the load is centered on the saddle.
• Ensure vehicle is secure and stable before working on, around or under.
Lowering Load
• Using a suitable jack, lift vehicle clear of stands.
• Disengage support pin from the extension column holes and carefully lower the column down to the lowest position.
Place support pin into holder.
• Remove stands. Follow procedures of jack operation to lower vehicle.
MAINTENANCE
Inspect each stand before use. Ensure all parts move freely. If rust appears, sand away the rust area and
cover with appropriate utility paint.
Part No. Description QTY
ZJ22-100 Extension Column Support Rod 1
3
Setup
•Prior to each use, visual inspecon (See Pg.2 ) shall be made to the device by checking for abnormal
condions, such as cracked welds, damaged, loose or missing parts.
•Consult the vehicle owner’s manual to determine the locaon of support points.
•Be sure to set the vehicle in park with the emergency brake on and wheels securely chocked.
•Be sure that the vehicle and the jack stands are on a hard, level surface.
Assembly
•Insert extension column into base collar.
Operation
Supporng a Load
•Properly chock the vehicle wheels.
•Li the extension column up to desired posion, insert support rod through the column
adjustment holes. Ensure the support rod is properly and fully engaged in the column holes
and securely rested on the collar.
•Slowly and carefully lower the vehicle onto the saddle. Be sure the load is centered on the
saddle.
•Ensure vehicle is secure and stable before working on, around or under.
Lowering Load
•Using a suitable jack, li vehicle clear of stands.
•Disengage support pin from the extension column holes and carefully lower the column
down to the lowest posion. Place support pin into holder.
•Remove stands. Follow procedures of jack operaon to lower vehicle.
Maintenance
Inspect each stand before use. Ensure all parts move freely. If rust appears, sand away the rust area and
cover with appropriate ulity paint.
Part Number
Description
Qt’y
ZJ22-100
Extension column support rod
1
* Items not idenfied by part number are not available for replacement.
Saddle
Extension Tube
Handle
Base
Extension Tube
Support Bar
Lanyard
Support Bar Holder
Collar
Height
Adjustment
Holes
Corresponding Radii
*Items not identified by part number are not available for replacement

ONE YEAR LIMITED WARRANTY
For a period of one (1) year from your purchase date, Ascot Supply will repair or replace (at its option) without charge,
your Ascot Supply product if it was purchased new and the product has failed
due to a defect in material or workmanship which you experienced during normal use of the
product. This limited warranty is your exclusive remedy.
You may be advised to return the product under warranty, freight prepaid, to the Ascot Supply service department.
If this Ascot Supply product is altered, abused, misused, modified or undergoes service by an
unauthorized technician, your warranty will be void. We are not responsible for damage to ornamental designs you
place on this Ascot Supply product and such ornamentation should not cover any warnings or instructions or they may
void the warranty. This warranty does not cover scratches, superficial dents and other abrasions to the paint finish that
occur under normal use.
Subject to the law in your state:
(1) Your sole and exclusive remedy is repair or replacement of the defective product as
described above.
(2) Ascot Supply is not liable for any incidental damages, including but not limited to, lost profits and
unforeseeable consequences.
(3) The repair and replacement of this product under the express limited warranty described
above is your exclusive remedy and is provided in lieu of all other warranties, express or
implied. All other warranties, including implied warranties and warranties of
merchantability or fitness for a particular purpose are disclaimed and, if disclaimer is
prohibited, these warranties are limited to one year from your date of purchase of this
product.
Some states’ laws do not allow limited durations on certain implied warranties and some states’ laws do not allow
limitations on incidental or consequential damages. You should consult the
law in your state to determine how your rights may vary.