Asmart Light CLH02 User manual
LED Corn Light Instruction
Can not use the electric generator to test the LED lamp.
Please avoid using the led fixture in environment where there is smoke,
sulfur, and corrosive substances. But if used in such environment,
make sure the led fixture is well protected by an enclosed lampshade
whose dimension is no less than below size, and whose material is
either glass or semi-glass, semi-metallic. Surface of the lampshade
shall not have any covering which prevents heat dissipationPower W
Volume CM
110
44*26*26
95
44*24*24
Rev A1
75
47*21*21
ADDED WEIGHT OF THE DEVICE MAY CAUSE INSTABILITY OF A FREE-STANDING
PORTABLELUMINAIRE. USE ONLY WITH A PORTABLE LUMINAIRE THAT IS
PROVIDED WITH A SHADE. THIS LAMP EMPLOYS LIGHT EMITTING DIODE
TECHNOLOGY AND UNLIKE TUNGSTEN-HALOGEN LAMPS DOES NOT
REQUIRE A BARRIER. LAMP IS SUITABLE FOR OPEN LUMINAIRES.
NOT FOR EMERGENCY LIGHTING.
ADDED WEIGHT OF THE DEVICE MAY CAUSE INSTABILITY OF A FREE STANDING
PORTABLE LUMINAIRE. UTILISER UNIQUEMENT AVEC UNE LAMPE DE TABLE
DOTÉE D’UN ABAT-JOUR. NE CONVIENT PAS AUX SORTIES DE SECOURS.
AVERTISSEMENT:
WARNING:
AVERTISSEMENT - PRECAUTIONNEZ-VOUS CONTRE DES CHOCS ÉLECTRIQUES.
L'INSTALLATION DES PIÈCES DE RECHANGE LED EST SEULEMENT EN CHARGE
DES PROFESSIONNELS. PRECAUTIONNEZ-VOUS CONTRE FEU. INSTALLER DES
PIÈCES DE RECHANGE SELON LES SPÉCIFICATIONS, VEILLER À CE QUE
LA PUISSANCE D'ENTRÉE NE DÉPASSE PAS LA PUISSANCE D'ENTRÉE DE
REMPLACEMENT DE LA LAMPE. NE FAITES PAS DE CONTACT AVEC LE CÂBLE
POINTUS OU MÉTALLIQUES, AFIN D'ÉVITER LE FIL USÉ. VÉRIFIER LE CIRCUIT
FERMÉ, AFIN DE DOMMAGES LES CÂBLES ET LES COMPOSANTS
ÉLECTRONIQUES LORS DE L'INSTALLATION DE FORAGE. NE PAS MODIFIER LA
STRUCTURE DU CIRCUIT FERMÉ ET LES COMPOSANTS ÉLECTRONIQUES OU
FORAGE SUR CELUI-CI LORS DE L'INSTALLATION DES PIÈCES DE RECHANGE.
WARNING – RISK OF FIRE OR ELECTRIC SHOCK. LED RETROFIT KIT INSTALLA
-TION REQUIRES KNOWLEDGE OF LUMINARIES ELECTRICAL SYSTEMS. IF NOT
QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED ELECTRI
-CIAN. WARNING – RISK OF FIRE OR ELECTRIC SHOCK. INSTALL THIS KIT ONLY
IN THE LUMINAIRES THAT HAVE THE CONSTRUCTION FEATURES AND DIMEN
-SIONS SHOWN IN THE PHOTOGRAPHS AND/OR DRAWINGS AND WHERE THE
INPUT RATING OF THE RETROFIT KIT DOES NOT EXCEED THE INPUT RATING
OF THE LUMINAIRE. WARNING – TO PREVENT WIRING DAMAGE OR ABRASION,
DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR OTHER SHARP
OBJECTS. WARNING – RISK OF FIRE OR ELECTRIC SHOCK. LUMINAIRE WIRING
AND ELECTRICAL PARTS MAY BE DAMAGED WHEN DRILLING FOR INSTALLATION
OF LED RETROFIT KIT. CHECK FOR ENCLOSED WIRING AND COMPONENTS.
DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR
ELECTRICAL COMPONENTS DURING KIT INSTALLATION.THIS RETROFIT KIT IS
ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF
THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING
JURISDICTION. INSTALLERS SHOULD NOT DISCONNECT EXISTING WIRES
FROM LAMPHOLDER TERMINALS TO MAKE 6 CONNECTIONS AT LAMPHOLDER
TERMINALS. INSTEAD INSTALLERS SHOULD CUT EXISTING LAMPHOLDER
LEADS AWAY FROM THE LAMPHOLDER AND MAKE 6 ELECTRICAL
CONNECTIONS TO LAMPHOLDER LEAD WIRES BY EMPLOYING APPLICABLE
CONNECTORS. THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY
EXITS OR NOT FOR EMERGENCY LIGHTING.
LED Corn Light Instruction
Application:
LED Retrofit Kit make it simple to replace: parking lot lighting, shoebox lighting,
street lighting, flood lighitng, wall pack lighting, and canopy lighting etc.
Product features:
ƹ120/280 degree lighting.
Can be with Clear or frosted PC cover.
ƹNo fan.ƹƹ75-110W lamp can be with AC120-277V internal driver.
75-110W Sealant pouring for whole driver and lamp plastic housing.
ƹLong lifespan and good heat dissipation.
ƹDirect replacement for Metal Halide, easy Installation.
ƹFits many different fixtures to replace traditional lamps.
ƹ
Installation Instructions:
Warning: Please make sure the power is off before installation.
1. Turn off the power switch.
2. Screw off the CFLor MHL or HPS and so on, see Figure 3 43.Take out the led corn lamp and screw it on, make sure the side with the sensor hole is in the same direction as the luminous surface of the lamp,
and then unfold the radiator to 180 degrees, see Figure (1)(2).
Figure 1 ,Figure 2Regular lamp Lamp with motion sensor or PIR sensor, See the lower right corner for installation instructions.
1 2 :AC internal driver,(Note: Pls make sure to take
off the ballast before installing led corn light,otherwise the ballast will produce
the resonance of high voltage and makes led corn light breakdown.)
4.security rope provided, pls fix the rope on the lamp with hand,
then fix the wire of other end on the shell, see Figure 2 .5. Turn on the power switch.( Finished!)
Installation of or PIR sensor
motion sensor
It could be easily installed using a straight screwdriver .
Use a flat-blade screwdriver to unscrew the plug and remove
the plug. And then, choose motion sensor or PIR sensor
to install and tighten.
the motion sensor has no dialing code,Note:
and a remote control is needed for adjustment.
Please refer to the instruction for remote
control adjustment.
Figure(3) Figure(4)
Figure(1) Figure(2)
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference received, including interference that may
cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note:This equipment has been tested and found to comply with the limits for a class B
digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequence energy and,if not
installed and used in accordance with the instructions,may cause harmful interference to
radio communications.However,there is no guarantee that interference will not occur in a
particular installation.if this equipmemt does cause harmful interference to radio or
television reception,which can be determined by turning the equipment off and on,the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an autlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
