ASROCK K8NF3-VSTA User manual

11
11
1
K8NF3-VSTA
User Manual
Version 1.0
Published January 2007
Copyright©2007 ASRock INC. All rights reserved.

22
22
2
Copyright Notice:Copyright Notice:
Copyright Notice:Copyright Notice:
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in
any language, in any form or by any means, except duplication of documentation by
the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be regis-
tered trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:Disclaimer:
Disclaimer:Disclaimer:
Disclaimer:
Specifications and information contained in this manual are furnished for informa-
tional use only and subject to change without notice, and should not be constructed
as a commitment by ASRock. ASRock assumes no responsibility for any errors or
omissions that may appear in this manual.
With respect to the contents of this manual, ASRock does not provide warranty of
any kind, either expressed or implied, including but not limited to the implied warran-
ties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the manual or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic
substance controlled in Perchlorate Best Management Practices (BMP) regulations
passed by the California Legislature. When you discard the Lithium battery in
California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com

33
33
3
ContentsContents
ContentsContents
Contents
1.1.
1.1.
1. IntroductionIntroduction
IntroductionIntroduction
Introduction ........................................................................................................................
........................................................................................................................
............................................................ 55
55
5
1.1 Package Contents..................................................................... 5
1.2 Specifications ........................................................................... 6
1.3 Minimum Hardware Requirement Table for Windows®VistaTM
Premium 2007 and Basic Logo ................................................. 9
1.4 Motherboard Layout ................................................................. 10
1.5 ASRock 8CH I/O........................................................................ 11
2.2.
2.2.
2. InstallationInstallation
InstallationInstallation
Installation ............................................................................................................................
............................................................................................................................
.............................................................. 1212
1212
12
Pre-installation Precautions ............................................................... 12
2.1 CPUInstallation ......................................................................... 13
2.2 Installation of CPU Fan and Heatsink ....................................... 13
2.3 Installation of Memory Modules (DIMM).................................... 14
2.4 Expansion Slots (PCI Slots and AGP Slot) ........................................ 15
2.5 Jumpers Setup.......................................................................... 16
2.6 Onboard Headers and Connectors.......................................... 17
2.7 Serial ATA (SATA) Hard Disks Installation ................................ 21
2.8 Hot Plug and Hot Swap Functions for SATA HDDs.................. 21
2.9 Driver InstallationGuide ............................................................ 21
2.10 Installing Windows®2000 / XP / XP 64-bit / VistaTM / VistaTM
64-bit Without RAID Functions.................................................. 22
2.11 Installing Windows® 2000 / XP / XP 64-bit With RAID
Functions. ................................................................................. 22
2.12 Untied Overclocking Technology .............................................. 24
3.3.
3.3.
3. BIOS SBIOS S
BIOS SBIOS S
BIOS SETUP UTILITYETUP UTILITY
ETUP UTILITYETUP UTILITY
ETUP UTILITY ......................................................................................................
......................................................................................................
................................................... 2525
2525
25
3.1 Introduction ............................................................................... 25
3.1.1 BIOS Menu Bar ............................................................... 25
3.1.2 Navigation Keys ............................................................. 26
3.2 Main Screen.............................................................................. 26
3.3 Advanced Screen .................................................................... 27
3.3.1 CPU Configuration .......................................................... 28
3.3.2 Chipset Configuration..................................................... 30
3.3.3 ACPI Configuration ......................................................... 32
3.3.4 IDE Configuration ............................................................ 33
3.3.5 PCIPnPConfiguration ...................................................... 35
3.3.6 Floppy Configuration ...................................................... 36
3.3.7 Super IO Configuration................................................... 36
3.3.8 USB Configuration .......................................................... 38
3.4 Hardware Health Event Monitoring Screen ............................. 39
3.5 Boot Screen.............................................................................. 40

44
44
4
3.5.1 Boot Settings Configuration ........................................... 40
3.6 Security Screen........................................................................ 41
3.7 Exit Screen ............................................................................... 42
4.4.
4.4.
4. Software SupportSoftware Support
Software SupportSoftware Support
Software Support ......................................................................................................
......................................................................................................
................................................... 4343
4343
43
4.1 Install Operating System........................................................... 43
4.2 Support CD Information............................................................. 43
4.2.1 Running Support CD....................................................... 43
4.2.2 Drivers Menu .................................................................. 43
4.2.3 Utilities Menu ................................................................... 43
4.2.4 Contact Information ........................................................ 43

55
55
5
1.1.
1.1.
1. IntroductionIntroduction
IntroductionIntroduction
Introduction
Thank you for purchasing ASRock K8NF3-VSTA motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control. It de-
livers excellent performance with robust design conforming to ASRock’s commit-
ment to quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-
step guide to the hardware installation. Chapter 3 and 4 contain the configuration
guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be
updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest VGA cards and CPU support lists on ASRock website
as well. ASRock website http://www.asrock.com
1.11.1
1.11.1
1.1 Package ContentsPackage Contents
Package ContentsPackage Contents
Package Contents
1 x ASRock K8NF3-VSTA Motherboard
(ATX Form Factor: 12.0-in x 7.5-in, 30.5 cm x 19.1 cm)
1 x ASRock K8NF3-VSTA Quick Installation Guide
1 x ASRock K8NF3-VSTA Support CD
1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)
1 x 3.5-in Floppy Drive Ribbon Cable
1 x SerialATA (SATA) Data Cable (Optional)
1 x SerialATA (SATA) HDD Power Cable (Optional)
1 xASRock 8CH I/O Shield

66
66
6
1.21.2
1.21.2
1.2 SpecificationsSpecifications
SpecificationsSpecifications
Specifications
Platform - ATX Form Factor: 12.0-in x 7.5-in, 30.5 cm x 19.1 cm
CPU - Socket 754 for AMDAthlonTM 64 and Sempron processors
- Supports AMD’s Cool ‘n’ QuietTM Technology
- FSB 800 MHz
- Supports Untied Overclocking Technology (see CAUTION 1)
- Supports Hyper-Transport Technology
Chipset - NVIDIA®nForce3 250
Memory - 2 xDDRDIMM slots
- SupportDDR400/333/266
- Max. capacity: 2GB
Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 2)
-ASRock U-COP (see CAUTION 3)
- Boot Failure Guard (B.F.G.)
Expansion Slot - 4 x PCI slots
- 1 x AGP 8X slot (see CAUTION 4)
Audio - 7.1 CH Windows®VistaTM Premium Level Superior Audio
(C-Media CM6501 Audio Codec with UAA architecture)
LAN - Realtek PHY RTL8201CL
- Speed: 10/100 Ethernet
- Supports Wake-On-LAN
Rear Panel I/O ASRock 8CH I/O
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x Serial Port: COM1
- 1 x Parallel Port (ECP/EPP Support)
- 4 x Ready-to-Use USB 2.0 Ports
- 1 x RJ-45 Port
- Audio Jack: Side Speaker/Rear Speaker/Central Bass/
Line in/Front Speaker/Microphone (see CAUTION 5)
Connector - 2 x Serial ATA 1.5Gb/s connectors, support RAID (RAID 0,
RAID 1, JBOD) and “Hot Plug” functions
- 2 x ATA133 IDE connectors (support 4 x IDE devices)
- 1 x Floppy connector
- 1 x IR header
- 1 x Game header
- CPU/Chassis FANconnector
- 20 pin ATX power connector
- 4 pin 12V power connector
- CD in header

77
77
7
- Front panel audio connector
- 2 x USB 2.0 headers (support 4 USB 2.0 ports; 2 of them are
shared with USB23 ports on the I/O panel)
(see CAUTION 6)
BIOS Feature - 4MbAMI BIOS
-AMI Legal BIOS
- Supports “Plug and Play”
-ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
- SMBIOS 2.3.1 Support
Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)
Hardware - CPU Temperature Sensing
Monitor - Chassis Temperature Sensing
- CPU FanTachometer
- Chassis Fan Tachometer
- CPU Quiet Fan
- Voltage Monitoring: +12V, +5V, +3.3V, Vcore
OS - Microsoft® Windows® 2000/XP/XP 64-bit/VistaTM / VistaTM
64-bit compliant (see CAUTION 7)
Certifications - FCC, CE, Microsoft®WHQL Certificated
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technology, or using the third-
party overclocking tools. Overclocking may affect your system stability, or even
cause damage to the components and devices of your system. It should be done at
your own risk and expense. We are not responsible for possible damage caused by
overclocking.

88
88
8
CAUTION!
1. This motherboard supports Untied Overclocking Technology. Please read “Un-
tied Overclocking Technology” on page 24 for details.
2. Although this motherboard offers stepless control, it is not recommended to
perform over-clocking. Frequencies other than the recommended CPU bus
frequencies may cause the instability of the system or damage the CPU.
3. While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the motherboard
functions properly and unplug the power cord, then plug it back again. To
improve heat dissipation, remember to spray thermal grease between the
CPU and the heatsink when you install the PC system.
4. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!
It may cause permanent damage!
5. For microphone input, this motherboard supports both stereo and mono modes.
For audio output, this motherboard supports 2-channel, 4-channel, 6-channel,
and 8-channel modes. Please check the table on page 11 for proper connection.
6. Power Management for USB 2.0 works fine under Microsoft®Windows®
VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4.
7. Microsoft®Windows®VistaTM / VistaTM 64-bit driver keeps on updating now. As
long as we have the latest driver, we will update it to our website in the future.
Please visit our website for Microsoft®Windows®VistaTM / VistaTM 64-bit driver
and related information.
ASRock website http://www.asrock.com

99
99
9
1.31.3
1.31.3
1.3 Minimum Hardware RMinimum Hardware R
Minimum Hardware RMinimum Hardware R
Minimum Hardware Requirement Tequirement T
equirement Tequirement T
equirement Table for Wable for W
able for Wable for W
able for Windowsindows
indowsindows
indows®®
®®
®
VistaVista
VistaVista
VistaTMTM
TMTM
TM Premium 2007 and Basic LogoPremium 2007 and Basic Logo
Premium 2007 and Basic LogoPremium 2007 and Basic Logo
Premium 2007 and Basic Logo
For system integrators and users who purchase this motherboard and
plan to submit Windows®VistaTM Premium 2007 and Basic logo, please follow
below table for minimum hardware requirements.
CPU Sempron2500+
Memory 1GB system memory
VGA DX9.0 with WDDM Driver
with 128bit VGA memory (Premium)
with 64bit VGA memory (Basic)
* After June 1, 2007, all Windows®VistaTM systems are required to meet above minimum
hardware requirements in order to qualify for Windows®VistaTM Premium 2007 logo.

1010
1010
10
1.4 Motherboard Layout1.4 Motherboard Layout
1.4 Motherboard Layout1.4 Motherboard Layout
1.4 Motherboard Layout
SOCKET 754
DDR1 (64/72 bit, 184-pin module)
DDR2 (64/72 bit, 184-pin module)
ATXPWR1
FLOPPY1
CPU_FAN1
PS2_USB_PW1
1
ATX12V1
PCI 1
NVIDIA
nForce3 250
Chipset
CMOS
Battery
SATA2 SATA1
CLRCMOS2
1
CHA_FAN1
USB4_5
1
SPEAKER1
1
IR1
1
HDLED RESET
PLED PWRBTN
1
PANEL1
4Mb
BIOS
Super
I/O
AUDIO
CODEC
AUDIO1
JR1 JL1
1
CD1
DDR400
7.1CH
K8NF3-VSTA
30.5cm (12.0-in)
19.1cm (7.5-in)
124
3
15
18 16
17
578
9
11
13
14
12
10
6
19
20
21
22
23
24
25
26
1.5V_AGP1
PCI 3
USB2_3
1
GAME1
1
LAN
PHY
PARALLEL PORT
COM1
PS2
Mouse
PS2
Keyboard
USB 2.0
T: USB 2
B: USB3
USB 2.0
T: USB0
B: USB1
Top:
RJ-45
Top:
REAR SPK
Center:
SIDE SPK
Bottom:
CTR BASS
Top:
LINE IN
Center:
FRONT
Bottom:
MIC IN
PCI 2
PCI 4
IDE2
IDE1
RAID
SATA
ATA133
USB2.0
AGP 8X
RoHS
27
1 PS2_USB_PW1 Jumper 15 System Panel Header (PANEL1)
2 ATX 12V Power Connector (ATX12V1) 16 Chassis Speaker Header (SPEAKER 1)
3 ATX Power Connector (ATXPWR1) 17 USB 2.0 Header (USB4_5, Blue)
4 754-Pin CPU Socket 18 Chassis Fan Connector (CHA_FAN1)
5 CPU Heatsink Retention Module 19 Floppy Connector (FLOPPY1)
6 CPU Fan Connector (CPU_FAN1) 20 Game Port Header (GAME1)
7 184-pin DDR DIMM Slots (DDR1- 2) 21 Front Panel Audio Header (AUDIO1)
8 Secondary IDE Connector (IDE2, Black) 22 JR1 JL1Jumper
9 Primary IDE Connector (IDE1, Blue) 23 PCI Slots (PCI1- 4)
10 Primary Serial ATA Connector (SATA1) 24 Internal Audio Connector: CD1 (Black)
11 Secondary Serial ATA Connector (SATA2) 25 Flash Memory
12 AGP Slot (1.5V_AGP1) 26 Infrared Module Header (IR1)
13 NVIDIA Single Chipset 27 Shared USB 2.0 Header (USB2_3, Blue)
14 Clear CMOS Jumper (CLRCMOS2)

1111
1111
11
1.51.5
1.51.5
1.5 ASRock 8CH I/OASRock 8CH I/O
ASRock 8CH I/OASRock 8CH I/O
ASRock 8CH I/O
1 Parallel Port 8 Microphone (Pink)
2 RJ-45 Port 9 USB 2.0 Ports (USB01)
3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23)
4 Rear Speaker (Black) 11 Serial Port: COM1
5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple)
6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)
*7 Front Speaker (Lime)
* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See
the table below for connection details in accordance with the type of speaker you use.
TABLE for Audio Output Connection
Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker
(No. 7) (No. 4) (No. 5) (No. 3)
2 V -- -- --
4 V -- -- V
6V--VV
8VVVV
12
3
4
5
6
7
8
910
11
12
13

1212
1212
12
2.2.
2.2.
2. InstallationInstallation
InstallationInstallation
Installation
K8NF3-VSTA is anATX form factor (12.0-in x 7.5-in, 30.5 cm x 19.1 cm) motherboard.
Before you install the motherboard, study the configuration of your chassis to en-
sure that the motherboard fits into it.
Pre-installation PrecautionsPre-installation Precautions
Pre-installation PrecautionsPre-installation Precautions
Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
Before you install or remove any component, ensure that the
power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
1. Unplug the power cord from the wall socket before touching any
component.
2. To avoid damaging the motherboard components due to static
electricity, NEVER place your motherboard directly on the carpet or
the like. Also remember to use a grounded wrist strap or touch a
safety grounded object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-
static pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the motherboard
to the chassis, please do not over-tighten the screws! Doing so may
damage the motherboard.

1313
1313
13
2.12.1
2.12.1
2.1 CPU InstallationCPU Installation
CPU InstallationCPU Installation
CPU Installation
Step 1. Unlock the socket by lifting the lever up to a 90oangle.
Step 2. Position the CPU directly above the socket such that the CPU corner with
the golden triangle matches the socket corner with a small triangle.
Step 3. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the CPU
into the socket to avoid bending of the pins.
Step 4. When the CPU is in place, press it firmly on the socket while you push
down the socket lever to secure the CPU. The lever clicks on the side tab
to indicate that it is locked.
2.22.2
2.22.2
2.2 Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink
Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink
Installation of CPU Fan and Heatsink
After you install the CPU into this motherboard, it is necessary to install a
larger heatsink and cooling fan to dissipate heat. You also need to spray
thermal grease between the CPU and the heatsink to improve heat
dissipation. Make sure that the CPU and the heatsink are securely fas-
tened and in good contact with each other. Then connect the CPU fan to
the CPU FAN connector (CPU_FAN1, see Page 10,No. 6). For proper
installation, please kindly refer to the instruction manuals of the CPU fan
and the heatsink.
STEP 1:
Lift Up The Socket Lever
STEP 2 / STEP 3:
Match The CPU Golden Triangle
To The Socket Corner Small
Triangle
STEP 4:
Push Down And Lock
The Socket Lever
Lever 90° Up
CPU Golden Triangle
Socket Corner Small Triangle

1414
1414
14
notch
break
notch
break
2.32.3
2.32.3
2.3 Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)
Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)
Installation of Memory Modules (DIMM)
This motherboard is equipped with two 184-pinDDR (DoubleData Rate) DIMM slots.
Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward.
Step 2. Align aDIMM on the slot such that the notch on theDIMM matches the break
on the slot.
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into
the slot at incorrect orientation.
Step 3. Firmly insert theDIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.

1515
1515
15
2.42.4
2.42.4
2.4 Expansion Slots (PCI Slots and AGP Slot)Expansion Slots (PCI Slots and AGP Slot)
Expansion Slots (PCI Slots and AGP Slot)Expansion Slots (PCI Slots and AGP Slot)
Expansion Slots (PCI Slots and AGP Slot)
There are 4 PCI slots and 1 AGP slot on K8NF3-VSTA motherboard.
PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
AGP slot: The AGP slot is used to install a graphics card. TheASRock AGP slot has
a special design of clasp that can securely fasten the inserted graphics
card.
Please do NOT use a 3.3V AGP card on the AGP slot of this
motherboard! It may cause permanent damage! For the voltage infor-
mation of your AGP card, please check with the AGP card vendors.
Installing an expansion cardInstalling an expansion card
Installing an expansion cardInstalling an expansion card
Installing an expansion card
Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed in
a chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the
screws for later use.
Step 4. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Step 5. Fasten the card to the chassis with screws.
Step 6. Replace the system cover.

1616
1616
16
+5V
1_2
+5VSB
2_3
2.52.5
2.52.5
2.5 Jumpers SetupJumpers Setup
Jumpers SetupJumpers Setup
Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when jumper cap is
placed on these 2 pins.
Jumper Setting
PS2_USB_PW1 Short pin2, pin3 to enable
(see p.10, No. 1) +5VSB (standby) for PS/2 or
USB wake up events.
Note: To select +5VSB, it requires 2 Amp and higher standby current provided by
power supply.
JR1 JL1 Jumper
(seep.10, No.22)
Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel
audio connectors can work.
Clear CMOS Jumper
(CLRCMOS2)
(seep.10, No.14)
Note: CLRCMOS2 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system
setup parameters. To clear and reset the system parameters to default setup,
please turn off the computer and unplug the power cord from the power
supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3
on CLRCMOS2 for 5 seconds. However, please do not clear the CMOS right
after you update the BIOS. If you need to clear the CMOS when you just finish
updating the BIOS, you must boot up the system first, and then shut it down
before you do the clear-CMOS action.
JL1 JR1
Clear CMOS
2_3
1_2
Default

1717
1717
17
FLOPPY1
Pin1
IDE1
PIN1
IDE2
PIN1
thered-striped side to Pin1
connect the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductorATA 66/100/133 cable
2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors
2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
•
Floppy Connector
(33-pinFLOPPY1)
(seep.10 No.19)
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE Connector (Blue) Secondary IDE Connector (Black)
(39-pin IDE1, see p.10 No. 9) (39-pin IDE2, see p.10 No. 8)
Note: If you use only one IDE device on this motherboard, please set the IDE
device as “Master”. Please refer to the instruction of your IDE device vendor
for the details. Besides, to optimize compatibility and performance, please
connect your hard disk drive to the primary IDE connector (IDE1, blue) and
CD-ROM to the secondary IDE connector (IDE2, black).
Serial ATA Connectors These two Serial ATA (SATA)
(SATA1:seep.10 No. 10) connectors support SATA data
(SATA2:seep.10 No. 11) cables for internal storage
devices. The current SATA
interface allows up to 1.5 Gb/s
data transfer rate.
Serial ATA (SATA) Either end of the SATAdata cable
Data Cable can be connected to the SATA
(Optional) hard disk or the SATAconnector
on the motherboard.
SATA2 SATA1

1818
1818
18
connect to the SATA HDD
powerconnector
connect tothe
powersupply
Serial ATA (SATA) Please connect the black end of
Power Cable SATA power cable to the power
(Optional) connector on each drive. Then
connect the white end of SATA
power cable to the power
connector of the power supply.
USB 2.0 Header Besides four default USB 2.0
(9-pinUSB4_5) ports on the I/O panel, there are
(seep.10 No.17) two USB 2.0 headers on this
motherboard. Each USB 2.0
header cansupport two USB
2.0 ports. The shared USB 2.0
header (USB2_3) is shared with
Shared USB 2.0 Header USB ports 23 on the I/O panel.
(9-pinUSB2_3) When using the front panel USB
(see p.10 No. 27) ports by attaching the front panel
USB cable to USB2_3 header,
the USB ports 23 on the I/O panel
will not be able to function.
Infrared Module Header This header supports an
(5-pin IR1) optional wireless transmitting
(seep.10 No.26) and receiving infrared module.
Internal Audio Connectors This connector allows you
(4-pin CD1) to receive stereo audio input
(CD1: see p.10 No. 24) from sound sources such as
a CD-ROM,DVD-ROM, TV
tuner card, or MPEG card.
Front PanelAudio Header This is an interface for front
(8-pin AUDIO1) panel audio cable that allows
(seep.10 No.21) convenient connection and
control of audio devices.
1
IRTX
IRRX
GND
+5VSB
DUMMY
USB_PWR
USB_PWR
P+5
P-5
P+4
P-4
GND
GND
DUMMY
1
1
USB_PWR
P-2
GND
DUMMY
USB_PWR
P+2
GND
P-3
P+3
GND
AUD-OUT-L
1
BACKOUT-R
GND
AUD-OUT-R
MIC-POWER
MIC
BACKOUT-L
CD1

1919
1919
19
+5V
DUMMY
DUMMY
SPEAKER
1
GND
PWRBTN#
PLED-
PLED+
DUMMY
RESET#
GND
HDLED+
HDLED-
1
System Panel Header This header accommodates
(9-pinPANEL1) several system front panel
(seep.10 No.15) functions.
Chassis Speaker Header Please connect the chassis
(4-pinSPEAKER 1) speaker to this header.
(seep.10 No.16)
Chassis Fan Connector Please connect a chassis fan
(3-pin CHA_FAN1) cable to this connector and
(seep.10 No.18) match the black wire to the
ground pin.
CPU Fan Connector Please connect the CPU fan
(4-pin CPU_FAN1) cable to this connector and
(see p.10 No. 6) match the black wire to the
ground pin.
ATX Power Connector Please connect an ATX power
(20-pinATXPWR1) supply to this connector.
(see p.10 No. 3)
ATX 12V Power Connector Please note that it is necessary
(4-pin ATX12V1) to connect a power supply with
(see p.10 No. 2) ATX 12V plug to this connector.
Failing to do so will cause power
up failure.
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3.
3-PinFanInstallation
Pin 1-3 Connected
GND
+12V
CHA_FAN_SPEED
GND
+12V
CPU_FAN_SPEED
FAN_SPEED_CONTROL
1 2 3 4

2020
2020
20
MIDI_OUT
JAB2
JBY
JBB2
MIDI_IN
+5V
JAY
GND
GND
1
JAX
JAB1
+5V
JBX
JBB1
+5V
Game Port Header Connect a Game cable to this
(15-pinGAME1) header if the Game port bracket
(see p.10 No. 20) is installed.