Atex GL10M User manual

Long Silicone Light RGB GL10M Installation Manual
We will appreciate for your purchase of 'Long Silicone Light'. Please use this manual and install correctly and safely.
※ May not ship with endcap and adhesive such as custom specification products.
□If you have any questions about this product,
please contact our sales offices as below.
ATEX CO.,LTD
Hikaren Building No.B, 2-3-20, Toukou, Hakata-Ku, Fukuoka-City,
Fukuoka, 812-0008,Japan
TEL [phone] FAX [phone]
URL http://www.atex-jp.com
Advanced Technology Expert America Inc.
386 Beech Ave. #B1, Torrance, CA 90501, USA
TEL [phone] FAX [phone]
Advanced Technology Expert International Pte Ltd
25 Tagore Lane #03-11, Singapore Godown, Singapore 787602
TEL/FAX : [phone]
The warranty is valid for 1 year after the delivery.
Bending Radius
Straight Channel
ACCESSORIES (OPTION)
FJB30-01
When installing Long Silicone Light,
they can be used with Aluminium Channel.
Aluminium / L=1000mm
FAC10-01S
□
Product Number
LED
Product Name
MAX. R30 mm (Length direction)
FAS00-01S
Aluminium / L=1000mm
Remarks
WARRANTY
Product Name
Light Source
Fixing material
CONTACT US
Flexible Channel
environment
Dimension
Accessories (Include)
LED Pitch
Endcap×1, Adhesive×1
160 g / m
(Dust and Water proof）
Long Silicone Light RGB COLOR
10 mm
Weight
WARNING
PRECAUTIONS
The power switch must be turn off when performing
installation or removal.
Please do not miswire the poｌarity of power supply. It will
cause problems.
Please be careful that eyes might be hurt when you look
straight at light emitting part.
When installed in a closed device, ambient temparature
must be -10 to 55℃.
Please be careful about static electricity.
It will damage LED's.
Please note that there is some variation in color among
LED's.
Power Supply voltage is 24Vdc only.
Please do not apply other voltage such as AC100 to
230V. It will cause fume or fire.
It is indoor/outdoor use. It can not be used at the
following places,such as "Under watar " "High humidity
and High temperature""Atomosphere of corrosive gas
""Damage from salt breeze".Because it will cause fume.
When bending horizontaly , minimum allowable Bending
Radius is 30mm.
It is not allowed to bend verticaly. It will cause cracks at
the solder points.
GL10-90A1M-01
Product No.
SPECIFICATION
W88.8 (13)×H 15.5 (19.7) ×L mm ( ) size of ends
Supply Voltage
Power Consumption
Cut Unit
Use at
COLOR
Red,Green,.Blue and synthetic colors
Indoor/Outdoor -10～55℃
DC24V
20 W / m
at every 18 LED's
3D Drawing
□
□
□
□
□
□
□
□
□
unit：mm
2D Drawing
For Keeping
915 ～ 4515 ±15
13
19.7
150

Long Silicone Light RGB GL10M Installation Manual
We will appreciate for your purchase of 'Long Silicone Light'. Please use this manual and install correctly and safely.
HOW TO INSTALL (RECOMMEND)
DIMMING SYSTEM
PROCESS
①Please install the aluminum channel
①with M3 Flat-head screws.
②Please push the product into the channel carefully.
③From prevention of fall, please use Fixing
③materials with M4 Pan-head screws.
(Recommend installation pitch ： 240mm pitch）
The length of product can be adjusted.
Before the length is adjusted, please read page 3
carefully.
It may cause No-lighting because of wrong
cutting.
For Keeping
When installing this product, please use the
aluminum channel and the fixing material.
Fixing material
Aluminum channel
Product
M3 Flat-head Screws
M4 Pan-head Screws
Width = 33mm
240mm Pitch
DMX Dimming
Controller
AC 100V
to
AC 240V
Signal Line
(DMX+)
(DMX-)
(GND)
Power Line
(24V+)
(24V-)
Address 1 to 3
DMX Driver
Long Silicone Light RGB
Repeater
(Commercially Available)
Power Supply Unit
DC24V
DMX Driver
DMX Driver
Address 7 to 9
Address 10 to 12
DMX Driver
Address 4 to 6

Long Silicone Light RGB GL10M Installation Manual
We will appreciate for your purchase of 'Long Silicone Light'. Please use this manual and install correctly and safely.
Method of cutting Long Silicone Light RGB
Cut straight at the red line
Endcap installation after cutting.
Applying an adhesive
Endcap
It can be cut at every 18 LED's from the end.
CORRECT
WRONG
Incorrect cutting Pattern Location
Parts of the No's of 18 LEDs Magnifying
Correct cutting Pattern Location
Important
No-lighting occurs when you cut as shown in the figure below
No-lighting occurs by improper cutting.
For Keeping