Atlas fan company Patricia-5 User manual

READ AND SAVE THESE INSTRUCTIONS
Patricia
60", 52" or 42"
CEILING FAN
Please do not use any electric or battery powered tools in the assembly and installation of
this or any Matthews Fan Company product.
FAN RATING AC 120V. 60Hz FOR DAMP LOCATION
Patricia-3
Patricia-5

Tools and Materials Required.........................................................................................
Package Contents .........................................................................................................
Safety Rules...................................................................................................................
Mounting Options...........................................................................................................
Hanging the Fan ............................................................................................................
Make the Electric Connections.......................................................................................
Finishing the Installation.................................................................................................
Attaching the Fan Blades...............................................................................................
Attaching the Mounting Plate.........................................................................................
Installing the Light Kit.....................................................................................................
Programming Your Fan and Operating the Remote Control and Wall Control............
Operating Your Fan......................................................................................................
Care of Your Fan..........................................................................................................
Troubleshooting............................................................................................................
TABLE OF CONTENTS
1
1
2
3
4
5
7
8
9
9
10
11
12
12

1
2. PACKAGE CONTENTS
Unpack your fan and check the contents. You should
have the following items:
a-1. Blade set (3) (for PA3-CR)
a-2. Blade set (5) (for PA5-CR)
b. Hanger bracket assembly
c. Ball / down rod assembly
d. Coupling cover
e. Fan motor assembly
f. Fan housing
g. Mounting plate
h. 16W LED light kit
i. Glass shade assembly
j. Additional metal light cover
k. Hand held transmitter+holder+2 mounting screws
l. Wall transmitter incl. 2 mounting screws and 3
wire nuts
m. Wall plate incl. 1 face plate and 2 mounting screws
n. 12V batteries (2)
o. Package hardware
1) Mounting hardware:
wood screws (2), screws (2),
lock washers (2), washers (2),
star washers (2), wire nuts (3)
2) Blade attachment hardware:
screws (11), lock washers (11), flat washers (11)
Please do not use any electric or battery powered
tools in the assembly and installation of this or any
Matthews Fan Company product.
a-1
a-2
b
c
d
e
f
g
o
j
k
i
h
Philips screwdriver
Blade screwdriver
11 mm wrench
Step ladder
Wire cutters
1. TOOLS AND MATERIALS
REQUIRED
l
m
n

1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local electrical
codes. Electrical installation should be
performed by a qualified licensed electrician.
3. WARNING: To reduce the risk of electrical
shock and fire, do not use this fan with any
solid-state fan speed control device.
4. WARNING: To Reduce The Risk Of Fire,
Electric Shock, Or Personal Injury, Mount To
Outlet Box Marked Acceptable for Fan
Support of 15.9 kg (35 lbs) or less And Use
Mounting Screws Provided With The Outlet
Box. Most outlet boxes commonly used for
the support of lighting fixtures are not
acceptable for fan support and may need to
be replaced, consult a qualified electrician if
in doubt.
5. The fan must be mounted with a minimum of
7 feet clearance from the trailing edge of the
blades to the floor.
6. To operate the reverse function on this fan,
press the reverse button while the fan is
running.
7. Avoid placing objects in the path of the
blades.
8. To avoid personal injury or damage to the fan
and other items, be cautious when working
around or cleaning the fan.
9. Do not use water or detergents when cleaning
the fan or fan blades. A dry dust cloth or lightly
dampened cloth will be suitable for most
cleaning.
10. After marking electrical connections, spliced
conductors should be turned upward and
pushed carefully up into outlet box. The
wires should be spread apart with the
grounded conductor and the equipment
-grounding conductor on one side of the
outlet box.
11. Electrical diagrams are reference only. Light
kit that are not packed with the fan must be
UL Listed and marked suitable for use with
the model fan you are installing. Switches
must be UL General Use Switches. Refer to
the Instructions packaged with the light kits
and switches for proper assembly.
2
3. SAFETY RULES
WARNING
TO REDUCE THE RISK OF PERSONAL
INJURY, DO NOT BEND THE BLADE
BRACKETS (ALSO REFERRED TO AS
FLANGES) DURING ASSEMBLY OR AFTER
INSTALLATION. DO NOT INSERT OBJECTS IN
THE PATH OF THE BLADES.
NOTE
SUITABLE FOR USE IN DAMP LOCATIONS!

3
4. MOUNTING OPTIONS
If there isn't an existing UL listed mounting box,
then read the following instructions. Disconnect the
power by removing fuses or turning off circuit
breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and building
materials. The outlet box and its support must be
able to fully support the moving weight of the fan
15.9 kgs (35lbs) or less. Do not use plastic outlet
boxes.
Figures 1,2 and 3 are examples of different ways to
mount the outlet box.
Note: The Fig. 3 are for use for downrod style only.
Note: You may need a longer downrod to maintain
proper blade clearance when installing on a steep,
sloped ceiling. (Fig. 3)
To hang your fan where there is an existing fixture
but no ceiling joist, you may need an installation
hanger bar as shown in Figure 4.
Outlet box
Outlet box
Figure 1
Figure 3
Figure 4
Outlet box
Figure 2
Provide strong
support
Recessed
outlet box
Ceiling
mounting
bracket
Angled ceiling
maximum 25º

4
Figure 6
Figure 5
Ceiling
hanger
bracket
Ceiling
canopy
Canopy
cover
5. HANGING THE FAN
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly.
1. Remove the decorative canopy bottom cover
from the canopy by turning the cover counter
clockwise. (Fig. 5)
2. Remove the hanger bracket from the canopy by
removing the 1 of 2 screws from the bottom of the
hanger bracket and loosening the other one a half
turn from the screw head. Next, turn the canopy
counter clockwise to removing the hanger bracket
from the canopy. (Fig. 5)
3. Secure the hanger bracket to the ceiling outlet
box using screws and washers included with your
outlet box. (Fig. 6)
4. Loosen the two set screws and remove the hitch
pin and lock pin from the central shaft/top coupling
of the motor assembly. Doing so will allow the
down rod to enter the central shaft. (Fig. 7)
5. Route wires exiting from the top of the fan motor
through the coupling cover, canopy cover and
canopy and then through the ball/downrod. (Fig. 7)
6. Align the holes at the bottom of the downrod
with the holes in the collar on top of the motor
housing. Carefully insert the hitch pin through the
holes in the collar and downrod. Be careful not to
jam the pin against the wiring inside the downrod.
Insert the lock pin through the hole near the end of
the hitch pin until it snaps into its locked position.
(Fig. 7)
Warning/Caution: Failure to properly install lock
pin as noted in step 6 could result in fan loosening
and possibly falling.
7. Tighten two set screws on top of the fan motor
firmly.
8. Now lift the motor assembly into position and
place the hanger ball into the hanger bracket.
Rotate down rod until the "Check Tab" has dropped
into the "Registration Slot" and the down rod and
ball assembly seat firmly. The down rod and ball
assembly should not rotate if this is done correctly.
(Fig. 8)
9. An additional safety support is provided to
prevent the fan from falling. Secure the safety cable
to the ceiling joist with screw and washer. (Fig. 8)
Figure 7
Figure 8
Tab
Mounting screws
(supplied with
electrical box)
UL Listed
electrical
box
Hanger bracket
Supply wires
Downrod
Coupling cover
Canopy
Canopy cover
Set screws
Hitch pin Lock pin
Registration
slot
Screw
Safety cable

5
6. MAKE THE ELECTRIC
CONNECTIONS
NOTE: Your fan has included as standard
equipment two types of controls: a hand held
remote control and a wall mounted wall control.
You may use both as long as the dip switches
are calibrated the same. Select one of the
controls at this moment for installation and
programming of your fan.
Disconnect the power at the electrical box.
Follow the steps below to connect the fan to
your household wiring. Use the wire connecting
nuts supplied with your fan. Secure the
connectors with electrical tape. Make sure there
are no loose strands or connections.
A. Hand held remote control
1. Connect the fan supply (black) wire to the
black household supply wire as shown in Figure
9.
2. Connect the neutral fan (white) wire to the
white neutral household wire. (Fig. 9)
3. Connect the fan ground wire (green) to the
household ground wire.
4. Check that the two plugs, large and small are
making proper contact. One plug is small with
only a single wire connection. The second plug
is larger and connects multiple colored wires.
5. After all splices are made, check to make
sure there are no loose strands. As an
additional precaution we suggest to secure the
plastic wire connectors to the wires with
electrical tape.
Figure 9
White (neutral)
Green or bare
copper (ground)
White ("AC IN N")
Ground (green)
(Connect to ground wire
on hanger bracket if no
house ground wire exists.)
Outlet box
Black ("AC IN L")
Black (motor)

6
B. Wall mount remote control
a. Wall control wire connection
1. Connect the wall control supply (black) wire to
the black household supply wire as shown in
Figure 10.
2. Connect the wall control (black) wire to the
white neutral household wire. (Fig. 10)
3. Connect the wall control ground wire (green) to
the household ground wire.
4. If your wall outlet box has a ground wire (green
or bare copper), connect the wall control's
yellow/green ground wire to it; otherwise connect
the wall control's yellow/green ground wire directly
to one of the screws from the wall outlet box.
b. Fan wire connection
1. Connect the fan supply (black) wire to the black
household supply wire (Conductor cable between
ceiling and wall outlet box). (Fig. 101)
2. Connect the neutral fan (white) wire to the white
neutral household wire.
3. Connect the fan ground wire (green) to the
household ground wire.
4. Check that the two plugs, large and small are
making proper contact. One plug is small with
only a single wire connection. The second plug
is larger and connects multiple colored wires.
5. After all connections are made, check to make
sure there are no loose strands. As an additional
precaution we suggest to secure the plastic wire
connectors to the wires with electrical tape.
c. Installing the wall control
1. Carefully tuck the wire connections inside the
junction box. Secure the wall control with the two
wall switch screws provided. (Fig. 11)
2. Attach the wall plate over the wall control and
secure with the two wall plate screws provided.
Disclaimer: If a wall switch is to be used, for
warranty to be valid, our included wall control
needs to be installed to operate this fan.
Figure 10
Figure 11
SUPPLY CIRCUIT
BLACK
Ground
Conductor
Ceiling
Outlet Box
Green Ground
Lead
Ground to
Downrod
GREEN
WHITE WHITE
BLACKBLACK
BLACK BLACK
BLACK

7
7. FINISHING THE
INSTALLATION
STANDARD CEILING INSTALLATION
1. Tuck connections neatly into ceiling outlet box.
2. Slide the canopy up to hanger bracket and place
the key hole on the canopy over the screw on the
hanger bracket, turn canopy until it locks in place at
the narrow section of the key holes. (Fig. 12)
3. Align the circular hole on canopy with the
remaining hole on the hanger bracket, secure by
tightening the two set screws. Note: Adjust the
canopy screws as necessary until the canopy and
canopy cover are snug.
Warning: Make sure tab at bottom of hanger
bracket is properly seated in groove of hanger ball
before attaching canopy to bracket. Failure to
properly seat tab in groove could cause damage to
electrical wiring.
INSTALLING THE FAN HOUSING
Raise the fan housing up against the mounting
plate. The four supports inside the fan housing
should be placed against the four studs on the
mounting plate. Twist the fan housing clockwise
until snug. (Fig. 13)
Figure 12
Figure 13
Outlet box
Hanger
bracket
Canopy
Canopy cover
Screws
Fan
housing
Studs

8
8. ATTACHING THE FAN
BLADES
1. Fasten blade to motor using the flat washers,
lock washers and screws supplied. (Fig. 14)
2. Repeat process with other blades. Tighten each
screw and make sure the blade is straight.
NOTE: This fan is supplied with two types of
blades for installation. Please reference the
important diagram (Fig. 15) when attaching your
fan blades.
The inner holes are for 3 blades. (for PA3)
The outer holes are for 5 blades. (for PA5)
Figure 14
Figure 15
Blade
Screw
Flat washers
Lock washers

10. INSTALLING THE LIGHT
KIT
REMEMBER: To disconnect the power.
If you do not plan to install the
light kit with your fan at this time,
skip step 1, 2, 3 & 4.
1. Remove 1 of the 3 screws from the mounting
plate and loosen the other 2 screws. (Do not
remove)
2. Raise and hold the LED light kit close to the
mounting plate and proceed to do the wire
connections. Make the 2-pin wire connections:
(Fig. 17)
- Red to white
- Black to black
3. Place the key holes from the light kit over the 2
screws previously loosened from the mounting
plate, turn the light kit until it locks in place at the
narrow section of the key holes. Secure by
tightening the 2 screws previously loosened and
the one previously removed. (Fig. 17)
4. Raise the glass shade assembly up against the
mounting plate. The three slots inside the mounting
plate should be placed against the three studs on
the glass shade assembly, and secure it to the
mounting plate until snug.
5. If installing the optional metal light cover, make
sure is securely tighten.
NOTE: The metal light cover included with your
fan is an option to replace the glass for the light in
the event that you prefer not to use the light
feature of your fan. The metal light cover is not
necessary for the light operation; it can be saved
for later use if desired.
9
Figure 17
Figure 16
9. ATTACHING THE
MOUNTING PLATE
Step 1. Remove 1 of the 3 screws from the
mounting ring and keep it for future use. Loosen
the other 2 screws. (Do not remove)
Step 2. Place the key holes on the mounting plate
over the 2 screws previously loosened from the
mounting ring, turn mounting plate until it locks in
place at the narrow section of the key holes.
Secure by tightening the 2 screws previously
loosened and the one previously removed. (Fig.
16)
Glass shade
assembly
LED light kit
Connectors
Screws
studs
Slots
Mounting plate
Metal light
cover
Screws
Mounting ring
Mounting
plate

10
Figure 20
Figure 18
Figure 19
ON ECE
1234
ON
D
ON ECE
ON
D
Restore power to ceiling fan and test for proper
operation.
A. I, II, III, IV, V and VI button:
These six buttons are used to set the fan speed as
follows:
I = minimum speed
II = low speed
III = medium low speed
IV = medium speed
V = medium high speed
VI = high speed
B. button:
This button turns the fan off.
C. Reverse button:
This button is to control fan direction
D. Light button
This button is to control light. Switch the “D” and “ON”
dip switch on the back of transmitter to decide the light
in “ON/OFF” or “Dimmable” condition.
E. SET code setting button:
Your DC brushless motor is equipped with automatically
learned type remote control and a wall control. If two
fans or more in a house, it is recommended that you not
use the factory code settings. Change codes setting to
any other combination of dip switch setting to avoid fan
interference issues, but users need to do control setting
process as below once the code setting is changed.
Please refer the "D" "SET" code setting button section.
Follow the below steps to set the remote control:
The auto learning function will only mandate within 60
seconds when turning the fan’s AC power ON.
a) Select desired frequency from the transmitter.
b) From the wall or remote transmitter, press the “SET”
button, and hold the “SET” button for over 10 seconds.
Once the receiver has detected the frequency, the light
will flash twice, and the fan will automatically begin to
operate and start to rotate in the counterclockwise
direction and on the highest RPM for 3 minutes. When
counter clockwise rotation has finished, the fan will
automatically reverse to clockwise direction again to the
highest RPM for 3 minutes. Fan will shut off when the
self calibration test has finished. The total self calibration
test will last about 6 minutes.
11. PROGRAMMING YOUR
FAN AND OPERATING
THE REMOTE CONTROL
AND WALL CONTROL
Before programming takes place, fan must be fully
assembled and mounted to the ceiling with blades
attached. You must also choose which control you
will be using for programming the fan, the remote
or the wall control. No other wall control should be
used with this fan but that which was included.
Using another wall control other than ours will
damage your fan and void your warranty.
Install one 23A/12V battery (included). To prevent
damage to transmitter, remove the battery if not used
for long periods of time (Fig. 18 & 19)

11
Figure 21
Figure 22
12. OPERATING YOUR
FAN
Speed settings for warm or cool weather depend on
factors such as the room size. Ceiling height,
number of fans and so on.
NOTE: To operate the reverse function on this fan,
press the reverse button while the fan is running.
Warm weather - (Forward) A downward airflow
creates a cooling effect as shown in Fig. 21. This
allows you to set your air conditioner on a warmer
setting without affecting your comfort.
Cool weather - (Reverse) An upward airflow moves
warm air off the ceiling area as shown in Fig. 22.
This allows you to set your heating unit on a cooler
setting without affecting your comfort.
NOTE: If the self calibration test failed, turn the AC
power off; restore power and process the self
calibration test again.
NOTE: During self calibration test, the remote and
the wall control are non-functional.
NOTE: The learning frequency function and self
calibration test will continue to retain the last set
frequency and calibration set even when the AC
power is shut off. If the frequency is changed the
self calibration test will occur again.
F. “D” and “ON” dip switch:
The “ON” selection is the light dimmable selection and is
to be used with all bulbs except for CFL bulbs. The “D”
selection is the light ON only (no dimming function) and
is to be used with CFL bulbs as CFL bulbs in most cases
cannot be used with dimming controllers.
This receiver provides the following protective
function:
1. Lock Rotor Position: The DC motor has a built-in
safety against a stalled or locked rotor condition
(stalled blade rotation). If there is an obstruction or
fault with the motor, the current monitoring function
will automatically turn power off to the motor after 30
seconds. Remove the obstruction and turn the AC
power off. Restore power and re-start fan motor.
2. Over 80W protection: When the receiver detects
motor power consumption which is greater than
80W, the receiver power will be stopped and
operation will immediately discontinue. Wait for 5
seconds and then turn the receiver power back on.

12
14. TROUBLESHOOTING
13 CARE OF YOUR FAN
Here are some suggestions to help you maintain your fan
1. Because of the fan's natural movement, some connections may become loose. Check the support connections,
brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan
from ceiling.)
2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or lint-free
cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
Do not use water when cleaning. This could damage the motor, or the wood, or possibly cause an electrical
shock.
3. You can apply a light coat of furniture polish to the wood blades for additional protection and enhanced beauty.
Cover small scratches with a light application of shoe polish.
4. There is no need to oil your fan. The motor has permanently lubricated bearings.
IMPORTANT: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT
ANY REPAIRS. REFER TO THE SECTION "MAKING ELECTRICAL CONNECTIONS".
Problem
Fan will not start.
Fan is noisy.
Remote control
malfunction.
Fan wobble.
Fan has jerky
movement
Fan has lost its
programming
repeatedly
Solution
1. Check circuit fuses or breakers.
2. Check line wire connections to the fan and switch wire connections in the switch housing.
CAUTION: Make sure main power is off.
3. Check that the battery of the remote is functional.
4. Check to make sure all receiver plugs are connected at top of motor.
5. Re-do steps for programming on page 7.
1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade bracket to the motor hub is tight.
3. Make sure wire nut connections are not rubbing against each other or the interior wall of
the switch housing. CAUTION: Make sure main power is off.
4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear
during this time.
5. If using an optional light kit, make sure the screws securing the light plate are tight.
6. Some fan motors are sensitive to signals from solid-state variable speed controls. If you
have installed this type of control, choose and install another type of control.
7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the
ceiling.
1. Do not connect the fan to a wall mounted variable speed control. Use our proprietary
provided wall control.
2. Make sure the dip switches are set correctly.
1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal. Check this level
by selecting a point on the ceiling above the tip of one of the blades. Measure this
distance.Rotate the fan until the next blade is positioned for measurement. Repeat for
each blade. The distance deviation should be equal within 1/8".
3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades
can redistribute the weight and possibly result in smoother operation.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN.
DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
1. Turn the AC power off to fan, and re-do steps for programming on page 10.
2. If fan still has jerky movement, verify that both motor wire plugs are properly connected.
1. Turn the AC power off to fan, and re-do steps for programming on page 10.
2. Do not turn off fan from wall switch. Use only remote to regulate fan.

LIMITED LIFETIME WARRANTY
MATTHEWS-GERBAR, LTD. DBA MATTHEWS FAN COMPANY LIFETIME LIMITED WARRANTY.
Ceiling fans are warranted by Matthews-Gerbar, Ltd. to the original user against defects in workmanship or
materials under normal use and inside installation for: Motors: Lifetime of original purchaser: Labor &
Component parts: (lights, finish, blades, etc…): one year after date of purchase, Light Bulbs: no warranty.
Any part, which is determined by Matthews-Gerbar, Ltd. to be defective in material or workmanship and
returned to an authorized service location, as Matthews-Gerbar, Ltd. designates, shipping costs prepaid, will
be, as the exclusive remedy, repaired or replaced at Matthews-Gerbar Ltd.'s option providing that proof of
purchase is provided. For limited warranty claim procedures, see PROMPT DISPOSITION below. This
limited warranty gives purchasers specific legal rights, which may vary from state to state.
LIMITATION OF LIABILITY. To the extent allowable under law, Matthews-Gerbar, Ltd.'s liability for
consequential and incidental damages is expressly disclaimed. Matthews-Gerbar, Ltd.'s liability in all events
is limited to, and shall not exceed, the purchase price paid.
WARRANTY DISCLAIMER. Matthews-Gerbar, Ltd. has made a diligent effort to illustrate and describe the
products in this literature accurately: however, such illustrations and descriptions are for the sole purpose of
identification, and do not express or imply that the products will necessarily conform to the illustrations or
descriptions. Furthermore, there is no express warranty derived from any viewed sample or model.
Matthews-Gerbar, Ltd. disclaims any expressed warranty and implied warranty of merchantability
and fitness for a particular use.
Except as provided below, no warranty or affirmation of fact, expressed or implied, other than as stated in
"Limited Lifetime Warranty" above is made or authorized by Matthews-Gerbar, Ltd.
PRODUCT SUITABILITY. Many states and localities have codes and regulations governing sales,
construction, installation and/or use of products for certain purposes, which may vary from those in
neighboring areas. While Matthews-Gerbar, Ltd. attempts to assure that its products comply with such
codes, it cannot guarantee compliance and cannot be responsible for how the product is installed or used.
Before purchase and use of a product, please review the product application and national and local codes
and regulations, and be sure that the product, installation, and use will comply with them.
Matthews-Gerbar, Ltd. disclaims any expressed warranty and implied warranty of merchantability
and fitness for a particular use if any modifications are made to the original manufacturer's product.
Certain aspects of disclaimers are not applicable to consumer products: e.g.(a) some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you: (b) also, some states do not allow limitations on how long an implied warranty lasts,
consequently the above limitation may not apply to you.
OTHER EXCLUSIONS. This warranty does not cover defects caused by: exposure to extremes of heat and
humidity, neglect, modification, alteration, repair or service of the enclosed product by anyone other than an
authorized Matthews-Gerbar, Ltd. service center; physical abuse to, or misuse of, the product or operation of
it in a manner contrary to the accompanying instructions; or shipment of the product to a Matthews-Gerbar,
Ltd. dealer or service center for service. This warranty also excludes all costs arising from adjustment of
user controls, products purchased outside of the U.S.A., and costs for initial technical adjustments (set-up).
Matthews-Gerbar assumes no liability for labor costs, installation costs or other losses. Consult the operating
instructions included with the product for information regarding user controls.
PROMPT DISPOSITION. Matthews-Gerbar, Ltd. will make a good faith effort for prompt correction respect
to any product, which proves to be defective within limited lifetime warranty. For any product believed to be
defective within limited lifetime warranty, first call or write dealer from whom the product was purchased.
Dealer will give additional directions. If unable to resolve satisfactorily, call Matthews-Gerbar, Ltd. at the
phone number below, giving the dealer's name, address, date and number of dealer's invoice, and describe
the nature of the defect. Title and risk of loss pass to buyer on delivery to common carrier. If product was
damaged in transit to you, file claim with the carrier.
MATTHEWS-GERBAR, LTD.
1881 Industrial Drive - Libertyville, IL - 60048
Tel [phone] - Fax [phone]