Atlas WDF User manual

ICE CREAM FREEZER-WDF & WDF-L SERIES
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment!
Notify carrier of damage! Inspect all components immediately. See page 1.
WDF
DROP-IN ICE CREAM FREEZER
REFRIGERATED, SELF CONTAINED
Effective Date: 2017
IMPORTANT INFORMATION
READ BEFORE USE
WDF-L
DROP-IN SLIM-LINE ICE CREM
FREEZER , REFRIGERATED, SELF
CONTAINED

CONTENTS
RECEIVING AND INSPECTING THE EQUIPMENT
1. VISUALLY INSPECT THE SHIPPING CRATE. DAMAGE SHOULD BE NOTED AND REPORTED TO THE DELIVERING CARRIER.
6. SAVE ALL CRATING MATERIALS UNTIL INSPECTION HAS BEEN MADE OR WAIVED.
5. FREIGHT CARRIERS CAN SUPPLY THE NECESSARY FORMS ON REQUEST.
4. REQUEST AN INSPECTION BY THE SHIPPING COMPANY FOR THE DAMAGED EQUIPMENT WITHIN 10 DAYS FROM RECEIPT OF THE
EQUIPMENT
3. IF CRATE IS NOT DAMAGED AND THERE IS CONCEALED DAMAGE TO THE EQUIPMENT, NOTIFY THE CARRIER. NOTIFICATION MUST BE
MADE VERBALLY AND IN WRITING.
2. IF DAMAGED, OPEN AND INSPECT CONTENTS WITH CARRIER.
SERIAL NUMBER LOCATION
INSTALLATION DATE: _____________________________________________
MODEL #:_______________________________________________________
SERIAL #: _______________________________________________________
THE SERIAL AND MODEL # CAN BE FOUND ON THE CONDENSING UNIT ENCLOSURE - SEE OPERATORS SIDE CONTROL PANEL WHEN
CALLING ATLAS FOR PARTS AND SERVICE ALWAYS HAVE THIS INFORMATION AVAILABLE.
RECEIVING & INSPECTING EQUIPMENT....................................................................................................................................................................................1
SERIAL AND MODEL # LOCATION..............................................................................................................................................................................................1
WDF - SPECIFICATIONS, FEATURES AND ACCESSORIES.....................................................................................................................................................2
ELECTRICAL CHARACTERISTICS, CUT-OUT REQUIREMENTS AND REFRIGERATION CHART...................................................................................3
WDF-L - SPECIFICATIONS, FEATURES AND ACCESSORIES.................................................................................................................................................4
ELECTRICAL CHARACTERISTICS, CUT-OUT REQUIRMENTS AND REFRIGERATION CHART.....................................................................................5
WDF & WDF-L INSTALLATION, OPERATION AND S/S MAINTENANCE...........................................................................................................................6
PARTS LIST...........................................................................................................................................................................................................................................7
TROUBLE SHOOTING GUIDE..........................................................................................................................................................................................................8
ELECTRICAL SCHEMATIC.................................................................................................................................................................................................................9
LIMITED WARRANTY.........................................................................................................................................................................................................................10
WARRANTY INFORMATION............................................................................................................................................................................................................11

* Units with these accessories are not currently UL listed.
roject: ___________
Item No.: ___________
Quantity: ___________
DR P-IN SERVING EQUIPMENT
ICE CREAM
FREEZER
Refrigerated,
Self-Contained
WDF-2
WDF-3
T P: Constructed of 18 gauge, type 304 stainless steel, die
stamped with a raised perimeter bead. There shall be a solid
vinyl gasket under the beaded edge to form a seal to the
counter top, thus preventing seepage or marring the counter
top.
LINER: The inner liner shall be 18 gauge, type 304 stainless
steel, one piece construction, all welded, ground and polished
to a uniform finish. All corners are coved with a minimum 1/4"
radius on the horizontal edges and a minimum 3/4" radius on
the vertical edges. The liner has copper tubing firmly soldered
to the exterior sides and bottom. The unit is provided with an
all stainless steel insulated, hinged, lift off lid, with plastic
coated pulls.
INSULATI N: The unit is fully insulated with high density
polystyrene, 2-1/2" thick on all sides, and enclosed with a 22
gauge galvanized steel outer liner.
REFRIGERATI N SYSTEM: The compressor housing shall
be fabricated from 14 gauge galvanized and bolted to the
base of the unit. A fully self-contained condensing unit is pro-
vided with a hermetically sealed compressor and a thermostat
control. The system is fully charged with CFC free refrigerant
and ready to operate.
N TE: roper ventilation must be provided in counter.
ELECTRICAL: The unit will be wired for 15 amps., 120 volt,
single phase operation, with an on/off thermostat switch and
pilot light. A 6' long, 3-wire cord and plug (NEMA 5-15 ) will
be provided.
Specifications s bject to change witho t notice.
SPECIFICATI NS STANDARD FEATURES
gFully insulated for maximum efficiency and energy
savings
gRemovable S/S hinged lid
gFactory applied gasket - makes installation a snap and
seals units to the counter top, thus eliminating
seepage
g Ideal for frozen dessert or use it as a mug or plate
chiller
g1-Year arts & Labor Warranty
g NSF Certified and UL Listed
ACCESS RIES
g 5YW - 5-Year Compressor Warranty
gHinged lexiglas Lid
g LLD - Lid Locking Device
g 2060-1 - Condensate Evaporator
g RS - Remote On/Off Switch for counter mounting
g * 220 Volt - 50 Cycle Compressor
DI-41
WDF-2
*Please see peration & Installation Manual for ALL operation and maintenance details.

Atlas Metal Industries 1135 NW 159th Dr. Miami, FL 33169 [phone] Fax: [phone] atlasfoodserv.com
WDFX - REFRIGERATED ICE CREAM FREEZER
WITH UT C MPRESS R
Units include Refrigerated Ice Cream Freezer,
Thermostat, Cap Tube & Drier (for hook up in field
by others)
C MPRESS RS F R REM TE INSTALLATI NS
2029-1 - 1/4 H for WDFX-2 & 3
DI-42
A
24”
PLAN VIEW
16”
10-3/4”
B 21-1/2”
13-1/2”
ELEVATI N
16-1/2”
21-3/4”
END VIEW
M DEL “A” “B” INTERI R
DIMENSI NS
CU. FT.
CAPACITY
LBS.
CAPACITY
ELECTRICAL
CHARACTERISTICS
CUT- UT
REQUIRED
SHIP WT.
(LBS.)
WDF-2 29-3/4”
(75.5cm) 6-7/8” (17.4cm) 16-1/2” X 22-1/2” X 13-1/2” (41.9 X 57.1 X 34.2cm) 4.5 100 (45.3kg) 6.8amps. X 120V X 1/4H
22-1/4” X 28”
(56.5 X 71.1cm) 194 (88kg)
WDF-3 43-1/2”
(110.4cm) 3” (7.6cm) 16-1/2” X 36-1/2” X 13-1/2” (41.9 X 92.7 X 34.2cm) 7.8 150 (68kg) 6.8amps. X 120V X 1/4H
22-1/4” X 41-3/4”
(56.5 X 106cm) 232 (105.2kg)
9/17-sc
WDF-2: 22-1/2” I.D.
WDF-3: 36-1/4” I.D.
M DEL HP REF. Z. L W
PSIG.
HIGH
PSIG.
BTU
M10 90A
WDF-2 1/4 134A 4 min 3 in 129 1070
WDF-3 1/4 134A 5 min 3 in 129 1070
REFRIGERATI N CHART

* Units with these accessories are not currently UL listed.
roject: ___________
Item No.: ___________
Quantity: ___________
SLIM-LINE DR P-IN SERVING EQUIPMENT
SLIM-LINE
ICE CREAM
FREEZER
Refrigerated,
Self-Contained
WDF-L
T P: Constructed of 18 gauge, type 304 stainless steel, die
stamped with a raised perimeter bead. There shall be a solid
vinyl gasket under the beaded edge to form a seal to the
counter top, thus preventing seepage or marring of the
counter top.
LINER: The inner liner shall be 18 gauge, type 304 stainless
steel, one piece construction, all welded, ground and polished
to a uniform finish. All corners are coved with a minimum 1/4”
radius on the horizontal edges and a minimum 3/4” radius on
the vertical edges. The liner has copper tubing firmly soldered
to the exterior sides and bottom. The unit is provided with an
all stainless steel, insulated, hinged, lift off lid, with plastic
coated pulls.
INSULATI N: The unit is fully insulated with high density
polystyrene, 2-1/2" thick on all sides, and enclosed with a 22
gauge galvanized steel outer liner.
REFRIGERATI N SYSTEM: The compressor housing shall
be fabricated from formed angles and bolted to the base of
the unit. A fully self-contained condensing unit is provided with
a hermetically sealed compressor and a thermostat control.
The system is fully charged with CFC free refrigerant and
ready to operate.
N TE: roper ventilation must be provided in counter.
ELECTRICAL: The unit will be wired for 15 amps., 120 volt,
single phase operation, with an on/off thermostat switch and
pilot light. A 6' long, 3-wire cord and plug (NEMA 5-15 ) will
be provided.
Specifications subject to change ithout notice.
SPECIFICATI NS STANDARD FEATURES
gSlim-line configuration - it can install in counters only
16-1/2” wide
gFully insulated for maximum efficiency and energy
savings
gRemovable S/S hinged lid
gFactory applied gasket - makes installation a snap and
seals units to the counter top, thus eliminating
seepage
g Ideal for any frozen dessert or use it as a mug or plate
chiller
g1-Year arts & Labor Warranty
g NSF Certified and UL Listed
ACCESS RIES
g 5YW - 5-Year Compressor Warranty
gHinged lexiglas Lid
g LLD - Lid Locking Device
g 2060-1 - Condensate Evaporator
g RS - Remote On/Off Switch for counter mounting
g * 220 Volt - 50 Cycle Compressor
DI-43
WDF-L
*Please see peration & Installation Manual for ALL operation and maintenance details.

Atlas Metal Industries 1135 NW 159th Dr. Miami, FL 33169 [phone] Fax: [phone] atlasfoodserv.com
WDF-LX - REFRIGERATED ICE CREAM FREEZER
WITH UT C MPRESS R
Units include Refrigerated Ice Cream Freezer,
Thermostat, Cap Tube & Drier (for hook up in field
by others)
C MPRESS RS F R REM TE INSTALLATI NS
2029 - 1/5 H for WDF-LX
DI-44
27-3/4”
16-1/2”
PLAN VIEW
16”
10-3/4”
4-1/2” 18”
13”
ELEVATI N
10-3/4”
13-3/4”
END VIEW
M DEL SIZE
W x L x D
CU. FT.
CAPACITY
LBS.
CAPACITY
ELECTRICAL
CHARACTERISTICS CUT- UT REQUIRED SHIP WT. (LBS.)
WDF-L 22-1/2” X 11-1/4” X 13”
(57.2 X 28.6 X 33cm) 1.9 65 (29.5kg) 2.4 amps. - 120V
1/5 H
26” X 15”
(66 X 38.1cm) 158
(54kg)
9/17-sc
M DEL HP REF. Z. L W
PSIG.
HIGH
PSIG.
BTU
M10 90A
WDF-L 1/5 134A 2.5 min 3 in 129 505
REFRIGERATI N CHART

ICE CREAM FREEZERS
WDF & WDFL SERIES
---------------------------------------------------------------------------------------------------------------------------------------------------------
INSTALLATION
Provide the correct counter cut-out opening (see chart below) and drop in. The vinyl gasket assures
complete seating. A non-toxic silicone seal may be used between the gasket and counter top (not
required).
When installing unit in a counter, it is recommended that the operator side of the counter be completely
open for air circulation. When this is not possible, such as in an island counter, it is recommended that two
grill openings are provided approximately 18” x 18” of free air for intake and exhaust at the opposite ends
of the counter.
The unit is supplied with a power cord and NEMA plug. Refer to the data plate on the compressor housing
for the amperage and voltage information. Use a licensed electrician when installing power source.
---------------------------------------------------------------------------------------------------------------------------------------------------------
OPERATION
The unit is ready to operate as soon as it is plugged in. The thermostat has an off position and numbers
from #1 through #7 (number 7 is the coldest). The unit should be turned off every day after used and
turned on one hour before serving.
---------------------------------------------------------------------------------------------------------------------------------------------------------
MAINTENANCE
NEVER CLEAN PANS WITH A CHLORIDE BASED PRODUCT. CHLORIDES OR IMPROPER
CLEANING COULD SCAR, MARK AND/OR CORRODE PANS. DO NOT USE STEEL WOOL OR
ABRASIVE PRODUCTS. TO CLEAN USE SOAPY WARM WATER, RINSE THOROUGHLY TO
REMOVE ALL RESIDUES. FAILURE TO MEET THESE CONDITIONS WILL VOID
WARRANTY.
CLEAN CONDENSER COIL REGULARLY.
MODEL NUMBER CUT-OUT SIZE
WDF-2 22 1/4 X 28
WDF-3 22 1/4 X 41 3/4
WDF-L 15 X 26

Subsidiary of Mercury Aircraft, Inc.
1135 N.W. 159th DR., MIAMI, FL 33169
PHONE [phone], FAX [phone], E-mail: [e-mail]
PARTS LIST ICE CREAM FREEZERS
WDF & WDFL SERIES
87
6
5
4
2
3
1
WDF-2
SHOWN
ITEM NUMBER PART NUMBER DESCRIPTION
S11054 + Model # WDF Lid Assembly
1S33155-0 WDFL Lid Assembly
S11014-0 WDF Hinge
2S81809-0 WDFL Hinge
3 6043-0 Lid Handles
4 7002-0+Model # Vinyl Bead Gasket
5 1003-0 Power Cord with Plug
6 2043-0 Thermostat
7 1099-0 Pilot Light
2029-0 1/5 H.P. Compressor WDFL
82029-1 1/4 H.P. Compressor WDF-2 & 3
94043-1 Handle Screws (Not Shown)
10 7003-0+Model # Throat Gasket (Not Shown)
11 2027-0 0.031 Cap Tube for 1/5 H.P. Comp. WDFL only (Not Shown)
12 2026-0 0.042 Cap Tube for 1/4, H.P. Comp. (Not Shown)
13 2025-0 Drier (Not Shown)
14 7030-0 WDFL Plastic Underlid (Not shown)
15 7031-0 WDF-2-3 Plastic Underlid (Not Shown)
16 7032-0 WDF-3 Center Underlid (Not Shown)
16 600008 Thermostat Knob

Subsidiary of Mercury Aircraft, Inc.
1135 N.W. 159th DR., MIAMI, FL 33169
PHONE [phone], FAX [phone], E-mail: [e-mail]
Refrigerated Drop-In Trouble Shooting Guide
Symptom Probable Cause
Unit not plugged in.
No power at receptacle.
Thermostat and or switch not in the on position.
Unit may be in a defrost cycle (if supplied) wait approximately 20 min.
Unit will not run
Call factory for service at 1-800-762-7565
Condenser coil dirty
Inadequate ventilation.
Condenser runs but
short cycles
Call factory for service at 1-800-762-7565
Condenser coil dirty.
Inadequate ventilation.
Unit installed in a hot location
Call factory for service at 1-800-762-7565
Condenser runs
constantly.
NOTE: WF series runs constantly.
Food product must be chilled to 33-35 deg. when placed in unit.
Air movement over food product.
Food product not being stirred or rotated.
Food product not
cold enough.
Call factory for service at 1-800-762-7565

LIMITED WARRANTY
Atlas Metal Industries, Inc. warrants to the Purchaser of this product that the
same shall be free from defects in the workmanship and material for a period of
one year from the date of original installation of the equipment, but not to exceed
eighteen (18) months after date of shipment from factory. During this period of
time Atlas Metal Industries, Inc. will replace all defective parts and will pay for
authorized replacement labor. Replacement and installation of such parts and
labor shall be provided only upon prior written authority of Atlas Metal Industries,
Inc.
The Refrigeration warranty is for a twenty (20) month time period and includes
supplying the compressor at a no charge basis provided the damage to the
compressor was not caused by the customer or end user. Authorized
replacement labor will be paid for a period of one year from date of installation.
Freight costs for defective unit to and from Atlas Metal Industries, Inc. are not
included, and all defective parts must be returned to the factory freight prepaid
for evaluation. ALL WARRANTY LABOR MUST BE AUTHORIZED BY ATLAS
METAL INDUSTRIES, INC. PRIOR TO THE ACTUAL WORK BEING DONE.
This warranty does not apply to any equipment or any part thereof, which has
been subjected to shipping damage, improper voltage, alteration, abuse or
misuses, and does not cover loss of food, other products, or damage to property
due to mechanical or electrical malfunction.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION OF THE FACE HEREOF. SELLER DISCLAIMS ANY IMPLIED
WARRANTY OF MERCHANTABILITY OF THE GOODS OR THE FITNESS OF
THE GOODS FOR ANY PURPOSE AND BUYER AGREES THAT THE GOODS
ARE SOLD “AS IS.”

WARRANTY INFORMATION
In order to have your invoice approved for
payment by the factory, please note the following:
_______________________________________________
An authorization number must be obtained from
the factory prior to performing any warranty
service.
_______________________________________________
Atlas Metal will not approve excessive labor due to poor
access to the unit being serviced. If design does not
allow reasonable access, contact the factory.
_______________________________________________
All travel time that exceeds 100 miles round trip
must be authorized by the factory.
_____________________________________________________________________________________
Thank You:
Warranty service Dept.