Audio Technica ATS99 User manual

ATS99
Hypercardioid Dynamic Microphone
User Manual
English

1
Safety precautions
Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure
safety, observe all warnings and cautions while using the product.
Cautions for the product
Do not subject the product to strong impact to avoid malfunction.
Do not disassemble, modify or attempt to repair the product.
Do not handle the product with wet hands to avoid electric shock or injury.
Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty place.
Do not place the product on an unstable surface to avoid injury or malfunction due to falling or the like.

2
Notes on use
Be sure to read the connected device’s user manual before use.
When the product is used for a long time, the product may become discolored due to ultraviolet light (especially
direct sunlight) and wear.
Make sure to hold the plug when connecting and disconnecting the cable. The cable may become severed or an
accident may occur if you pull on the cable itself.
When using the cable, be careful not to twist it to prevent damage to the cable.
Do not wind the cable at the base of the plug to prevent a disconnection.
When plugging the cable into the microphone and the connected device, check that the connector is facing in the
correct direction before inserting it straight. Inserting the connector or plug diagonally may cause a malfunction.
For important recordings, perform a trial recording beforehand to make sure that the sound is recorded correctly.
Audio-Technica will not be liable in any way for any loss or damage to software or data connected to the product.

3
Included accessories
1 2 3
1
AT8470 stand clamp for 5/8”-27 threaded stands
2
5/8”-27 to 3/8”-16 threaded adapter
3
Pouch

4
Using the product
1Connect the product to a device with a microphone input (balanced input) for use.
2Use the product with the front part facing the sound source.

5
Connection procedure
The output connector is an XLR-M type with polarity as shown in the figure below.
21
3
1
PIN1 (ground)
2
PIN2 (hot)
3
PIN3 (cold)

6
Cleaning
Get into the habit of regularly cleaning the product to ensure that it will last for a long time. Do not use alcohol, paint
thinners, or other solvents for cleaning purposes.
Wipe dirt off the product with a dry cloth.
If the cables become dirty because of sweat, etc., wipe them with a dry cloth immediately after use. Failure to clean
the cables may cause them to deteriorate and harden over time, resulting in a malfunction.
If the product will not be used for an extended period of time, store it in a well-ventilated place free from
high temperatures and humidity.

7
Dimensions
181.5
φ50
φ21.4
(Unit: mm)

8
Specifications
Element Dynamic
Polar pattern Hypercardioid
Frequency response 60 to 16,000 Hz
Open circuit sensitivity -52 dB (0 dB = 1 V/Pa, 1 kHz)
Impedance 600 ohms
Weight 262 g (9.2 oz)
Dimensions 181.5 mm (7.1”) long, 50 mm (2.0”) maximum body diameter
Output connector Integral 3-pin XLR-M type
Included accessories AT8470 stand clamp for 5/8”-27 threaded stands, 5/8”-27 to 3/8”-16 threaded
adapter, Pouch
1 Pascal = 10 dynes/cm2= 10 microbars = 94 dB SPL
For product improvement, the product is subject to modification without notice.

9
Polar pattern/Frequency response
Polar pattern
200 Hz
1 kHz
5 kHz
8 kHz
SCALE IS 5 DECIBELS
PER DIVISION
LEGEND
240˚
180˚
210˚
270˚
300˚
330˚
0˚
150˚
120˚
90˚
30˚
60˚
Frequency response
20
10 dB
100
50 200 10k 5k
1k
500 2k 20k
0°, 50 cm
LEGEND
Frequency in Hertz
Response in dB
60 - 16,000 Hz

株式会社オーディオテクニカ
〒194-8666 東京都町田市西成瀬2-46-1
www.audio-technica.co.jp
Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
www.audio-technica.com
©2022 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com 142420770-02-01 ver.1 2022.11.01