Audiodesign KPRO 15.10 User manual

STAGE PRO series
User Manual
PROFESSIONAL SPEAKERS, AMPLIFIERS AND ACCESSORIES
Via dell’industria, 28 - 42025 CAVRIAGO (RE)
[phone] - Fax [phone]
www.audiodesign-pro.com KPRO 15.10
Full Range Sound System
[email protected]
Audiodesign Srl

Portable Full Range Sound System KPRO 15.10
Stage Pro Series
PRODUCT WARRANTY
For the warranty validation please fill this form and send it to AudioDesign within 10 days from the purchase date.
AUDIODESIGN srl
Via dell’Industria, 28
Corte Tegge
42025 Cavriago (RE)
ITALIA
Product details
Article Series No..
Dealer City
Purchase date Purchase price
Buyer details
Full name Age
Full adress
Occupation
e-mail
AUDIODESIGN guarantees the confidentiality of the data provided with this form
N O T E S
- 7 -
Portable Full Range Sound System KPRO 15.10
Stage Pro Series
Introduction
Thank you for purchasing an AudioDesign KPRO Active Sound system.
KPRO series is designed to provide an high and powerful sound quality in a compact size.
The main features are:
*Active subwoofer cabinet with additional amplifiers for the passive satellites.
*High sensitivity passive satellites.
*High and precise acoustic quality also with high power.
The final result is a full, detailed and powerful sound.
*Portability: the system is easy fit and portable by one person.
- 2 -
Application
The KPRO systems are a professional solution for every DJ or Live events where high pressure and extreme
sound quality is required.
Precautions:
Caution: When using any electric product , precautions should always be taken, including the following:
1) Read carefully all instructions before using the product.
2) To reduce the risk, strict supervision is necessary when the product is used near children.
3) Don't use the product near to water sources like sinks, kitchens, wet floors, pools,
or similar or when raining.
4) In case hearing losses or buzzing occur, please contact a doctor.
5) This products should be located so that its position does not interfere or reduce its proper ventilation.
6) This product should be site away from heat sources such as radiators or any other product that
generate heat.
7) This product should be connected to a power supply line only of the type described on the operating
instructions. Check always the status of the power cable.
8) In case you need to replace the fuse, unplug power supply before replacement. The fuse is located
over the power socket and needs to be replaced with a fuse of same type and value. If the fuse blows again,
please contact our service. DON'T replace it a second time with a higher value fuse.
9) Unplug power supply when left unused for a long period of time. Don't draw the cable but pull out the
plug.
10) Make sure that power switch can always be easily reached.
11) The product needs to be inspected by authorized or qualified personnel in case:
A- The power cable or plug are damaged
B- Objects or liquids fall inside the product
C- The product has been exposed to rain
D- The product doesn't appear to operate normally or exhibits a marked change in performance.
E- The product has fallen and been damaged.
12) DON'T operate on the product, except indications on the user's manual . Please refer to authorized
and qualified personnel for any other operation.
13) Caution: Don't place objects on the product's power cable or place it in a position where it could be
damaged or cause interferences. Improper installation could cause fire risk and/or personal injury.
Service
All Audio Design PRO products have been inspected and tested before leaving the factory and , if properly
used, they will work for many years. However, in case of any problem, please proceed in the following way:
Contact your dealer and inform about the defect you found
In case it won't be possible to solve the problem with the dealer, the product needs to be returned, preferably
in its original packaging or in a proper packing to protect it during the transport. Purchase documents must
be produced too.
Your dealer will arrange the shipment to our service centre.
Conformity:
Audiodesign Pro products comply with presently existing directives and standards.

Portable Full Range Sound System KPRO 15.10
Stage Pro Series
Technical Specification
SUBWOOFER STAGE PRO W15
INPUT LINE IN: 6.3 Sereo Jack Socket (Sleeve = Ground; Pin = +; Ring = -)
INPUT: Balanced and Unbalanced
OUTPUT LINE OUT PARALLEL: 6.3 Stereo Jack Socket (Sleeve = Ground; Pin = +; Ring = -)
SATELLITE OUTPUT: Speakon NL4 (pin 1+ = +, pin 1- = -)
AMPLIFIERS Subwoofer Power output: 300 W RMS (600 W Max)
Satellite Power output: 2x180 W RMS (2x360 W Max)
Sub PB electronic crossover: Frequency 100 Hz
SPEAKER Subwoofer: 1 x 15” (380 mm)
Frequency range: 20 ÷ 120 Hz (± 3 dB)
SPL Max: 123 dB
WEIGHT AND SIZE Subwoofer weight: 43,5 kg
Dimensions (WxLxH) cm: 58,5 x 48,5 x 55
SATELLITE STAGE PRO 10
INPUT SATELLITES INPUT: Speakon NL4 (pin 1+ = +, pin 1- = -)
SPEAKERS High Sensitivity Woofer: 1 x 10” (250 mm)
Compression Horn Tweeter: Voice coil 45 mm
50 mm vented voice coil
MAIN FEATURES
TOTAL IMPEDANCE:
4 Ohm
TOTAL POWER: 300 W RMS (600 W Max)
SPL Max: 127 dB
Frequency range: 70 ÷ 20000 Hz ()± 3 dB
WEIGHT AND SIZE Satellite Weight: 13 kg
Dimensions (WxLxH) cm: 32 x 30 x 46
Sensitivity Magnitude dB SPL/watt (4 ohm load) -
CURSOR: y = 53.6948 x = 20019.5313 (1025)
log Frequency - Hz
MLSSA: Frequency Domain
M
L
S
S
A
10000.01000.0100.020.0
auto
45.0
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
90.0
95.0
?
AUDIODESIGN PRO: KPRO 15.10
RESPONSE DIAGRAM OF THE STAGE PRO 15.10 SYSTEM
Tweeter Crossover: 8000 Hz 18 dB/oct Passive
- 6 -
Voice coil 100 mm
At 4 Ohm
Full Range Sound System KPRO 15.10
Stage Pro Series
SYSTEM COMPONENTS
The KPRO 15.10 system is composed by three elements:
Active Subwoofer STAGE PRO W15
1 Active Subwoofer STAGE PRO W15 and
2 Passive Satellites STAGE PRO 10
The active subwoofer STAGE PRO W15 is equipped with a 15" (380 mm) woofer
The cabinet integrate all the necessary electronics for amplification and system
3 AB class amplifiers for a total power of 600 W RMS (1060 W Max)
with 100 mm voice coil.
1 x 300 W RMS (600 W Max) Subwoofer
2 x 180 W RMS (360 W Max) Passive Satellites ( 4 Ohm load)
The subwoofer signal is Low Pass filteres at 100 Hz 12 db/oct.
Cabinet in high density MDF, anti-scratch embossed painting
LEFT RIGHT
SUBWOOFER LEVEL
LEVEL LEVEL
LINE OUT LINE IN LINE IN LINE OUT
POWER
400 W 4 OHM
POWER
150 W 8 OHM 150 W 8 OHM
Control and connecting plate
31
2
VOLTAGESELECTION
76
5910 8
13
11
12
1Electric net socket
2Voltage selector
3On/Off power swithc - In position 0 the system is Off
4On/Off LED light
5Left channel Line In - Balanced 6,3 mm Jack socket
4
6Left channel volume control - (volume control of the left passive satellite)
Left channel Line Out - 6,3 balanced Jack socket
7
8Right channel Line In - Balanced 6,3 mm Jack socket
9Right channel volume control (volume control of the right passive satellite)-
Right channel Line Out - 6,3 balanced Jack socket
10
Subwoofer Volume Control
11
Speakon socket for Left Satellite connection
12
Speakon socket for Right Satellite connection
13
processing :
It is a balanced input that can receive both balanced and unbalanced signals
It is a balanced output for the link of an additional amplifier
Dimension and Weight: 58,5 x 48,5 x 55 cm; 43 kg.
Pratical transport handles hollowed into the wood
Integral rigid metal grill
Housing hole for ø 35 mm stand tubes
14
Amplifier cooling fan; keep it clean for a correct ventilation.
14
It is a balanced input that can receive both balanced and unbalanced signals
It is a balanced output for the link of an additional amplifier
- 3 -

Portable Full Range Sound System KPRO 15.10
Stage Pro Series
Connect the components following the precedent wiring scheme .
Connection to the electric net
Check that Power switch is in position 0 and that net voltage corresponds to the one selected in the system.
3
.
Connect the supplied electric wire to an electric net socket equipped with a correct ground contact.
Connection to the mixer
Before making any connection to the mixer make sure the system power switch is Off in order to avoid damages.
Remember that electric net power il the last to be switced On and the first to be disconnected after use!
If you use balanced XLR outputs from the mixer , you need XLR > Stereo Jack signal wires, or XLR/XLR wires with a stereo
Jack adapter to connect to the Line In of the subwoofer amplifier.
If you use balanced Jack outputs from the mixer, you need Stereo Jack >Stereo Jack wires.
If you use unbalanced XLR outputs from the mixer, you need XLR >Jack Mono wires, or XLR/XLR wires with an adapter
Jack Mono to connect to the subwoofer Line In:
If you use unbalanced jack outputs from the mixer, you need Jack Mono >Jack Mono wires.
Satellite connection
Use wires with good quality Speakon plugs. Make sure to rotate the Speakon plugs clockwise up to the lock position.
System volume adjustment
The System KPRO 15.10 is not equipped with clipping limiters and with clipping LED lights therefore it is important to make a
The system can offer excellent performance and it should get good level imput signals , from the kind and the good
quality of wires and preventing any audio distorsion . A distorted audio signal will make a bad performance of the System
and can make serious damages to the System itself.
Therefore we invite you to follow carefully the following instructions for the level adjustment of every component.
Satellites volume adjustment
6
9
After having switched On the system, set the controls at 11 hours as described in the drawing. This is the optimal level
when you have a mixer with outputs peaks that are between 0 and + 3 dB
Now listen to the satellites; if you hear a distorsion or a signal saturation (by the microfone for instance) check the possibility
to reduce the signal from the audio source or the main output of the mixer. If it is not enough, reduce the volume of the
satellites untill you get an otimal sound.
Subwoofr volume adjustment
11
proper adjustment to the general features of the installation.
11
LEFT RIGHT
SUBWOOFER LEVEL
LEVEL LEVEL
LINE OUT LINE IN LINE IN LINE OUT
400 W 4 OHM
POWER
150 W 8 OHM 150 W 8 OHM
69
The adjustment of the system volume is to be made by the three LEVEL constrols
in the rear plate of the subwoofer:
- For the left satellite LEVEL LEFT
- For the right satellite LEVEL RIGHT
- For the subwoofer SUBWOOFER LEVEL
Before switching on the the system make sure that all three controls are turned
completely counterclockwise at level - .∞
Make the adjustment of the satellites first and then adjust the subwoofer level.
After having memorized the right position of the LEFT and RIGHT controls and having set them again to zero,
turn the control SUBWOOFER LEVEL and set it at 11 hours . This is the optimal level when you have a mixer
with outputs peaks that are between 0 and + 3 dB.
Now listen to the subwoofer ; if you hear bass distrorsions, turn slightly the subwoofer control counterclockwise.
Final adjusment of the System
Set the three controls in the optimal positions that you have identified and listen to the complete System, always with
the mixer outputs with maximum peaks between 0 and +3 dB.
If you hear to much basses , turn sligthly the control LEVEL SUB counterclockwise.
If basses are too low instead, turn slightly the controls LEVEL LEFT and RIGHT counterclockwise .
As a general rule , the output level of the mixers is set in a way that, with the sound peaks, it is between 0 to +3 dB
about. When the system K PRO 15.10 gets in the two Line In (5 and 8) a signal with that amplitude and it is
set as explained above, it grants the maximum performance in terms of maximum undistorted amplification (at clip
limit) and in this conditions you get the maximum possible sound pressure (SPL).
- 5 -
Portable Full Range Sound System KPRO 15.10
Stage Pro Series
High sensitivity passive satellites STAGE PRO 10
The high sensitivity satellite STAGE PRO 10 is composed by:
One 10" (250 mm) woofer with a 50 mm vented voice coil
One compression horn tweeter with a 45 mm voice coil
Cabinet in high density MDF , embossed anti-scratch painting
Housing hole for ø 35 mm stand tubes
Integral protection grill
High Pass Filter at 8000 Hz 18 dB/oct on tweeter
Impedance 4 ohm
Speakon socket for connection to the subwoofer amplifier
Dimension and Weight: 32 x 30 x 46 cm; 13 kg.
HIGHHIGHHIGHHIGH HIGHHIGH HIGH HIGH HIGHHIGH HIGH
EQEQ EQEQ EQ EQ EQ EQ
MIDMID MIDMIDMID MID MIDMID MID MID
12kHz12kHz12kHz 12kHz12kHz12kHz 12kHz 12kHz 12kHz 12kHz
2.5kHz
2.5kHz2.5kHz 2.5kHz2.5kHz2.5kHz 2.5kHz2.5kHz 2.5kHz2.5kHz 2.5kHz 2.5kHz
LOWLOWLOW LOWLOW LOWLOW LOW LOW LOW
80Hz80 Hz80Hz 80Hz80Hz 80 Hz 80Hz 80 Hz 80Hz
PREPREPREPREPREPREPREPRE PREPRE
AUXAUXAUXAUXAUXAUXAUX AUXAUXAUX
FXFXFXFXFXFX FXFX
PANPA N PANPAN PAN PAN BAL BAL
31 4 2 5 6 7/8 9/10
MUTEMUTE MUTEMUTE MUTE MUTEMUTE MUTE MUTE
ALT3-4ALT3-4ALT 3-4ALT3-4 ALT3-4ALT3-4ALT3-4ALT 3-4 ALT3-4ALT 3-4 ALT3-4ALT3-4 ALT3-4ALT3-4 ALT3-4ALT 3-4
CLIPCLIPCLIP CLIPCLIP CLIP CLIPCLIP CLIP CLIP
SOLOSOLO SOLOSOLO SOLO SOLO SOLO SOLO
MUTEMUTE MUTEMUTEMUTE MUTE MUTE MUTEMUTE MUTEMUTE
dBdB dBdB dB dB dB dB
1 2 569/10
111111 11 2 2
1 1 1
222222 22
AL T MAINMIX
3-4
34LR
SOLO
SOLO
FX FX
TOAUX
SEND1
MAINMIXMAINMIX
ALT3-4
AUXSENDS STEREOAUX RETURNS
PROGRAMPROGRAM
(PUSH )
2-TR/USB
ALT3-4
MAINMIX
SOURCESOURCE
MAX
2-TR/USBTO MAIN
PHONES/CTRLR
MAINSOLO PFL
MODE
SOLO(NORMAL)SOLO(NORMAL)
PFL(LEVELSET)PFL(LEVEL SET)
10
5
2
0
2
5
20
MIC3MIC 1MIC1 MIC4MIC2 MIC5 MIC 6
LINEIN 5/6 LINEIN 7/8LINE IN 7/8
RIGHTLEFT/ MONOMONO
AUXSENDS
2
1
2
1
FX
INPUT OUTPUT
CD/TAPECD/TAPE
00SMALLHALL00SMALL HALL
03MID HALL03MID HALL
06BIG HALL06BIG HALL
09CHURCH
10SMALLROOM10SMALLROOM
13MID ROOM13 MIDROOM
16BIG ROOM16BIGROOM
19CHAPEL19 CHAPEL
20SPRING20 SPRING
27SPRING27 SPRING
30GATEDREV30 GATED REV
36REVERSE36REVERSE
40EARLYREFL40EARLY REFL
44AMBIENCE44 AMBIENCE
48STADIUM48STADIUM
49AMBIENCEFX49AMBIENCEFX
50DELAY50DELAY
59ECHO59 ECHO
60CHORUS
66FLANGER66FLANGER
70PHASER70 PHASER
74PITCH SHIFT74PITCHSHIFT
80CHORUS & REVERB80CHORUS & REVERB
82FLANGER & REVERB82FLANGER&REVERB
84PHASER & REVERB84PHASER & REVERB
86PITCH & REVERB86PITCH & REVERB
88DELAY& REVERB88DELAY& REVERB
90DELAY& GATED90 DELAY&GATED
91DELAY& REVERSE91 DELAY&REVERSE
92DELAY& CHORUS92DELAY& CHORUS
94DELAY& FLANGER94 DELAY&FLANGER
96DELAY& PHASER96DELAY& PHASER
98DELAY& PITCH98DELAY & PITCH
24-BIT MULTI-FXPROCESSOR24-BIT MULTI-FX PROCESSOR
ULTRALOW-NOISEDESIGN
14-INPUT2/2-BUSMIC/LINE MIXER14-INPUT2/2-BUSMIC/LINE MIXER
WITHPREMIUMMIC PREAMPLIFIERS ANDWITHPREMIUMMIC PREAMPLIFIERS AND
DIGITAL24-BITMULTI-EFFECTS PROCESSORDIGITAL24-BITMULTI-EFFECTS PROCESSOR
USBAUDIOINTERFACEUSBAUDIOINTERFACE
34 7/8
PAM X 2 .6 2
LAM P12V12V
400400 mA
USB
INTERFAINTERFA CE
LEFT RIGHT
SUBWOOFER LEVEL
LEVEL LEVEL
LINEOUT LINE IN LINEIN LINEOUT
POWER
400W 4 OHM
POWER
150W 8 OHM 150 W 8 OHM
VOLTAGESELECTION
ELECTRIC NET
WIRING
- 4 -
6
3