Audipack FS-QR120 E Guide

Mounting and manual instruction
FS-QR120 E floor stand
Copyright Audipack

The FS-QR120E is a quick-release demountable floor stand with integrated
lifting mechanisme that raises the flat panel out of the flightcase for you.
Check at arriving of your package that your product isn’t damaged.
Whit damage please repoprt direcly to the transporter and Audipack to provide
a quick solution.
It is importand that at first use the lowest lifting head position is set to the
correct height. This is importand because the cams on the back of the Audipack
bracket on the back of the flat panel should corresond with the key holes of the
llifitng head in lowest position.
Please read the manual in full before starting to assemble the floor stand.
1.
Take away both flightcase lids and assemble the floorstands floor plate on the desired
position.
Make sure the floor plate is positioned on a level and flat surface.
2.
Install the 2 lower columns on the floor plate.
Take a way the C-formed covers (if needed) and secure the poles with the lock.
Be sure to install the colums with the “lip” front wards (see picture).

3.
Install the top part with the lifting head. Be sure to grip the handle and the side of the
colums. Do not lift at the lifting head!!
Do not lift the lifting head!
Grip handle
Make sure both pins slide in equally.
At uncontrolled placing it might be more difficult to connect the coloumns.
Also lock this assembly with the locks (tip: lock afther full completion)

4.
Plug in the power supply at the bottom of the lifting head.
Lower the lifting head to the lowest position by pressing the lowest button on the back.
230 volt power inlet with
loop to the monitor
“The right heigth is the height where the cams of the bracket are equally high as the key
holes in the lifting head”.
5.
Take the flightcase and move the back side of the flat panel in front of the floor stand.
Hook in the cams and press the lifting button. Stop the flat panel at any desired height
by pressing the middle button.
See chapter 6. for using the right mounting patttern and applicable loads.

6.
Flat panel heavier than 85 Kg must use the VESA 400 of 600 mounting pattern of the
system. When the screen is equipped with an equal mounting pattern on the back, please
contact Audipack for a fitting interface bracket.
VESA 400
VESA 600
L&S5
Applicable loads:
VESA 400 max. load 120 Kg
VESA 600 max. load 120 Kg
L&S5 max. load 85 Kg (with UFPRO)
Flat panel installation with VESA interface and cams.
When the flat panel is equipped with a VESA interface according the example, the screen
can be installed with the cams inserted directly in the back.
Choose one of the below (optional) cams to insert in the back.
M6 part no. 392618
M8 part no. 392318
M10 part no. 390618

7.
Flat panel security.
When the flat panel is installed it is possible to lock it onto the lifting head.
Release the screws on the top to slide away or position the cover plate.
In case of using the standard L&S5 interface a single padlock can be used to secure the
set.
8. Maintanance / fine tuning.
It is possible to correct the horizontallevel of the floor stand.
It might be possible after a while it must be corrected.
Take away the C-cover and udjust the M8 screw.
Hold down the cable, do not let it rotate while adjusting the M8 bolt.
This might result in a twisted cable.
Use wrench 13 mm to adjust.

9. Ajusting the lowest height at first use.
Be aware that it might be possible your model is equipped with 2 version of adjustment.
Please see chapter 9b when the lift is equipped with an electronic height adjustment.
The difference is that the electronic version has NO yellow and white adjustment knobs
as illustrated below.
When the Total system is installed please plug in the power.
The system is equipped with a wireless transmitter mounted on the back.
The system it selve is already set to standard limits. Never adjust the upper limit!
At the front of the lifting head coloured
knobs are visible. With an alan key the
positions can be set by adjusting their
position.
Adjusting the upper limit: White knob,
While giving command up adjust the white knob with
an alan key. Check left and right turning for adjusting
the right direction.
Adjusting lower position: Yellow knob,
While giving command up adjust the yellow knob with
an alan key. Check left and right turning for adjusting
the right direction.
Attention!
When adjusting the motor limit, be aware that mechanical limits may damage
the motor by setting the limits too far.
The motor can be overloaded and damage.
Max. motor runnig time 4 minutes.
Cooling down time 9 minutes at 4 minutes use.
Be sure that all parts move and rotate free.
Disconnect power afther installation.

9b.
This procedure is only applicable for FS-QR with electronic height adjustment setting.
During testing the system is aready set to maximum limits.
For the first use the lifting head must be set in height to let the cams from the monitor
bracket insert into the key holes of the lifting head (while the flat panel is still in the
flightcase).
Be aware of adjusting the bottom height for the DFS before installing the
monitor!
Work along the below protocol to set the right height.
Adjusting new lower position (only upwards).
-Plug in power and lower the lifting head to its lower limit.
-Use the rear mounted transmitter to control he system.
-Press the buttons UP en DOWN at the same time until the mounting head moves
up-and down shortly (program mode).
-Press single up to set the new height.
-For storing this position press the middle until the mounting head moves up-and
down shortly.
-The new position is set.

Technical details:
FS-QR120E
Maximale load:
-85 Kg with L&S5 mounting interface
-120 Kg with VESA 400 and 600 interface (with cams)
Power supply 230 VAC 50-60 Hz
Max. Motor running time 4 minuten (9 minuten “cool-down” period)
For questions or service please contact
Audipack
079-5931671
Technical department
Notes:

Re-programming the controll buttons (pairing).
All systems are pre-programmed in the factory.
When a new transmitter must be paired to the system check below protocol to perform
the “pairing”.
-Take out the transmitter from the system.
-Unplug the power for 20 seconds
-Plug in power for 10 seconds
-Unplug power for 2 seconds
-Plug back in the power, the motor will rotate for a few seconds.
-When the motor has stopped, press the small “prog”button on the back of the PCB
(see picture).
-The motor will rotate left and right shortly
Programm button

When the system does not respond to the command, a red light will blinck on the
remote.
-Check the battery and replace it.
-Plug in main power of the system.
Audipack
Industriestraat 2
2751 GT
Moerkapelle
[phone]
Function LED