Audix ATS Series User manual

OVERVIEW
The ATS1, ATS1LX and ATS1LP are the industry’s only programmable,
shock absorbent table stands with an LED indicator that does not
require external power supplies, eliminating the added expense and
complication associated with installation and wiring. The LED indicator
and audio switching circuitry operate on the same phantom power
source supplied to the microphone. The result is simplified installation
and reliable operation. The base has programmable functions that
are changed with a simple, intuitive dip switch which can be set to
operate in Toggle On, Toggle Off, Momentary Talk and Momentary
Mute modes. Also supplied within the base is a Low Cut Filter offering
additional protection from bass frequencies that may cause rumble or
hum. The ATS1LX and ATS1LP can be further programmed to operate
seamlessly with automated teleconferencing and switch systems in
external logic control mode.
The ATS is manufactured with a precision die cast zinc alloy base,
durable black E-coat finish, LED indicators and a noise free mechanical
switch.
MODEL VARIATIONS
ATS10 - Table stand with latching on/off switch
ATS 1 - Heavy-duty shock absorbent table stand with XLR connector,
programmable switch (on/off, talk/mute) and choice of two connector
versions:
• ATS1LP - 5-pin terminal connector located inside the base
• ATS1LX- 5-pin XLR output connector located at the back of
the base
OPTIONAL MICROPHONES
ADXSeries- ADX12, ADX18
MGSeries - MG12HC, MG15HC, MG18HC
MGNSeries - MGN6, MGN12, MGN29
MicroPod - MicroPod6, MicroPod6HC, MicroPod12, MicroPod12HC,
MicroPod18, MicroPod18HC, MicroPod6S, MicroPod6WS
ATS Series Microphone Table Stand
Accessory
FEATURES
• Heavy duty die cast base provides stability
• Shock mount design limits touch noise and
vibration
• Four programmable talk-mute functions
• Local remote control function settings
• Seamless integration with automated mixers
(ATS1LX & ATS1LP)
• Designed, assembled & tested in the USA
• 1 year warranty
APPLICATIONS
• Podium
• Lectern
• Video conferences
• Classrooms
• Courtrooms
• Boardrooms
ATS WITH OPTIONAL MIC CLOSE UP 3-PIN XLRm OUTPUT BOTTOM
ATS

ATS
ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
www.audixusa.com
503.682.6933 Fax: [phone]
Audix Corporation 9400 SW Barber St. Wilsonville, OR 97070 ver 2.0 07-15
SERVICE AND WARRANTY
The microphone stands are under warranty for a period of 1 year to be free of defects in material and workmanship. In the event of a product failure due to materials or workmanship,
Audix will repair or replace said product at no charge with proof of purchase. Audix does not pay or reimburse shipping costs for warranty repairs or returns. The warranty excludes any
causes other than manufacturing defects, such as normal wear, abuse, environmental damage, shipping damage or failure to use or maintain the product per the supplied instructions. No
Implied Warranties: All implied warranties, including but not limited to implied warranties of merchantability and fitness for a particular purpose are hereby excluded. The liability of Audix,
if any, for damages relating to allegedly defective products shall be limited to the actual price paid by Dealer for such products and shall in no event include incidental or consequential
damages of any kind. Should your microphone fail in any way, please contact the Audix Service department at 503.682.6933. A Return Authorization is required before returning any product.
OTHER THAN THIS WARRANTY, AUDIX MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS, THE USE OF THE PRODUCTS, THE PERFORMANCE OF THE PRODUCTS. AUDIX
SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES ARISING FROM OR BASED ON THE SALE, USE, STORAGE OR DISPOSAL OF THE PRODUCTS, AUDIX’S
SERVICE WORK, BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, OR ANY OTHER THEORY OF LIABILITY, EVEN IF AUDIX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SPECIFICATIONS
Mic Input Connector 3-pin XLRf
Base Output Connector 3-pin XLRm 3-pin XLRm 5-pin Terminal Block 5-pin XLRm
Switch Latching on/off Programmable on/off,
talk/mute
Programmable with remote
capabilities
Programmable with remote
capabilities
Off (mute) attenuation 45dB minimum
Power Requirements 11-52 V phantom DC
2mA typical
36-52 V phantom DC
2mA typical
36-52 V phantom DC
2mA typical
36-52 V phantom DC
2mA typical
Finish Matte Black
Length 160 mm / 6.9 in
Width 124 mm / 5.9 in
Height 45 mm / 1.8 in
Weight 1.4 kg / 3 lbs
Closure I/O voltage - - -0.5 to 30 V -0.5 to 30 V
Closure through current - - 200 mA 200 mA
On resistance - - >10 ohms >10 ohms
1/O leakage current - - 1uA 1uA
LED input - - Active when low (0.4 V DC)
TTL compatible
Active when low (0.4 V DC)
TTL compatible
ATS10 ATS1 ATS1LP ATS1LX
DIMENSIONS (mm)
ConnectingtheGooseneckMicrophone
Align the connector of the microphone to the XLR pins on top of the base. Gently
push down until the connectors “click” into place.
Important: The microphones will require phantom power to operate. This may be
supplied to the microphone from either the mixing console or a phantom power
supply.
SettingDipSwitch
Low Cut Filter: Inside the base, locate the switch on the PCB labeled “Low Cut Filter.”
The filter provides protection from bass frequencies that may cause rumble, hum,
or vibration by eliminating frequencies <100 Hz. To engage, push the dip switch to
the “on”position.
RemovingtheMicrophone
Press the release tab on the top of the base to remove the microphone.
ConnectingAudioandLogic
Use a balanced microphone cable and connect into the back side of the ATS base
until it “clicks”into place. To disconnect, press the tab on the microphone cable XLRf
connector and remove from base.
OPERATION
Conguration DipSwitchSetting

MomentaryMute:Mic is on;
switch is pressed and held to mute.
MomentaryTalk: Mic is off;
switch is pressed and held to talk.
ToggleO: Mic is on; switch is
pressed to turn the mic off and on
ToggleOn: Mic is off; switch is
pressed to turn the mic on and off
E L
3
2
1
E L
3
2
1
E L
3
2
1
E L
3
2
1
SWITCH SETTINGS
Low Cut Filter Switch
Setting Dip Switches
PRODUCT REGISTRATION
Please register your product online at www.audixusa.com/docs_12/about/product_registration.shtml.