AutoAqua Smart AWC Lite User manual

◆Installation
1. Can I fix the tube holder on a rimmed tank/sump?
2. How to install the prefilter properly?
3. Where should I place the Lifter Pump Holder?
5. What is the Anti-Siphon Pressure Height?
6. What is AWC Balance Mode?
7. What is the benefit of using Diaphragm Pump?
4. Where should I place the sensor?

◆Trouble Shooting
4. Why does Smart AWC Lite power on for only a short while and
give an audible alert?
3. Why is the water level always little higher/lower than the
sensor?
2. Why does the water keep dripping after pump has stopped?
1. How to replace diaphragm pump?
6. Can Smart AWC Lite detect empty reservoir?
5. Why the pump stops with beeping alarm but the water level
hasn’t reach the sensor?
7. What can QST do for you?
◆Product
1. What is the difference between AWC Lite and AWC Duo?

➢Can I fix the tube holder on a rimmed tank/sump?
Yes. You can pull out the ring of the tube holder and install
it on another nail to fix it on a rimmed tank/sump.

➢How to install the prefilter properly?
First, please connect the prefilter base to the prefilter.
Then, install the prefilter before the diaphragm pump (Inlet
Tube 1, 3, and 5 ) to protect it from clogged and damaged.
Note : please clean it every 3 to 6 months for the best
filtration performance.

➢Where should I place the Lifter Pump Holder?
We suggest to place Lifter Pump Holder at the waste water
reservoir, where the tube might be drift in the water.

➢Where should I place the sensor?
Place the sensor to the water level you desired.
*Please note : Set the sensor away from water outlet and direct
light to avoid bubble interference or malfunctions.

➢What is the Anti-Siphon Pressure Height?
There will be forward siphon when pump stops if the inlet tank
of water level is higher than the outlet tube.
To avoid forward siphon, the outlet tube must less than 1-ft
(30cm) below the water level of inlet tank.
Outlet must ALWAYS be out of water.
If you desired higher anti-siphon pressure height, you can buy
AUTOAQUA Anti-Siphon Valve. One anti-siphon valve can stop
about 60cm of water of the forward siphon pressure.

➢What is AWC Balance Mode?
After P3 pumps the new water in the tank, there will be a “AWC
Balance Mode” for 3 minutes with faded green AWC mode
(Manual/ 4H/ 12H/ 24H/ 48H) indicator.
Therefore, in balance mode, it will fill new water automatically
if the water level is lower than the sensor.
The final water level will be more accurate.
Water level might get down when refill water distributed goes
through the whole tank.

➢What is the benefit of using Diaphragm Pump?
⚫Add water smooth & consistent flow to reach the
desired water level accurately.
⚫Lessen the pressure to aquarium ecosystem.
⚫No wire in the tank for tidy aquarium.
⚫Able to run dry without damage for safety aquarium.

➢How to replace diaphragm pump?
⚫Step 1 : Press the release button on
the side and open the top
cover.
⚫Step 2 : Disassemble the PCB screw and the pump wire.
Then, remove the PCB and take the diaphragm
pump out.
⚫Step 3 : Place the new diaphragm
pump back in and
assemble pump wire, PCB,
and PCB screw back.
⚫Step 4 : Put the sensor wires in
the correct position.
⚫Step 5 : Make sure the springs are all
in the correct position before
close the cover.
⚫Step 6 : Plug the power in, reset the device, and test all the
buttons function. If the button works improperly,
please open the cover and adjust the
spring to the accurate position.