AutoLoc CL2000 Instruction Manual

CENTRAL LOCKING SYSTEM
CL2000 2 door standard
CL4000 4 door standard
CK2000 2 door with remote
CK4000 4 door with remote
CA2000 2 door with alarm
CA4000 4 door with alarm
USER GUIDE AND INSTALLATION MANUAL
INSTALLATION
Button 1 Button 2
Button 3 Button 4
Remote Transmitter
ACTUATOR MOUNTING
1. Remove all the handles, fittings, and arm rests from the door.
2. Remove the door's interior panel by inserting a screw driver between
the door, and door panel. Once inserted pry off the door panel by
pushing or pulling on the screwdriver (Figure1).
3. Carefully remove the clear PVC protective sheet from the door.
4. Locate your factory lock and unlock rod. This rod will be connected to
your unlock and lock button. When you pull or push this rod it will lock
or unlock your door. This rod maybe horizontal or vertical.
5. Locate a safe position to mount the door lock actuator parallel to the
factory door lock rod using the screws given (Figure 2). You can mount
the actuator directly to the door, or use the bracket to cross a part of the
door were there is no metal (Figure 2). In some cases, it is necessary to
bend the actuator rod in order to reach the factory rod. In these cases,
bend the rod so that the beginning and the end of the rod are horizontal
(Figure 4). Make sure there is plenty of room for the motor to travel up
and down. Check to make sure the motor will not interfere with the
window mechanisms.
6. Lock the door, then push the door actuator all the way down.
7. Place the actuator rod through the eye of the door lock plunger.
8. Attach the rod adapter to the actuators rod and tighten the screw
(Figure 3).
9. Connect the rod adapter to the factory door lock rod and secure by
tightening the screw (Figure 3).
10. Run the wires out of the door using the factory rubber tube to hide
the wires in the door jam. Make sure the wires do not get in the way of
the window mechanism.
11. Repeat steps 1-10 for each door.
WIRING
1. Run all the wires to the location of the door lock module. Be sure to
mount the module in a dry place (under the dash).
2. Connect the 5 wires from the actuator to the wire harness in
accordance with the same color.
3. Connect the separate black wire with the "U" shaped terminal to a
chassis ground (body metal).
4. Connect the separate red wire to a constant 12 volts positive power
source (battery).
CONTROL MODULE INSTALLATION
1. Connect the keyless entry units negative "-" LOCK output wire
(BLUE/WHITE) to the BROWN wire.
2. Connect the keyless entry units negative "-" UNLOCK output wire
(GREEN/WHITE) to the WHITE wire.
3. Connect the keyless entry units BLACK wire to a chassis ground (body
metal).
4. Install the fuse and connect the keyless entry units RED wire to a
constant 12 volts positive power source (battery).
5. (Optional) Use AutoLoc's power trunk kit for remote opening of your
trunk (part # PT1000).
TESTING
1. From the outside of the car, lock the drivers door. If the drivers and
passengers doors both lock then the system lock is working.
2. Now unlock the drivers door and if the passengers door is unlocked the
system unlock is working.
3. If you encounter a problem adjust the rod adopter to allow for more or
less travel on the factory rod.
CA2000/CA4000
Please refer to alarm instructions
for alarm specific wiring directions.

BROWN/BLACK
door lock
control box
remote
control
receiver
BLUE/WHITE
GREEN/WHITE
BLACK
RED
WHITE
15 AMP
FUSE
BROWN
GREEN
GREEN
BLUE
BLUE
BLACK
RED
ACTUATOR
ACTUATOR
ACTUATOR
ACTUATOR
OPTIONAL
Refer to alarm or keyless
installation instructions.
TRUNK/SHAVED DOOR HANDLE TRIGGER
USER GUIDE AND INSTALLATION MANUAL
NOTE: If parking lights are negative trigger, then connect 30 to chassis ground.
OPTIONAL FOR CL, CK, CA400 KITS
•
BROWN
•
WHITE

WIRING DIAGRAMS
figure 2
Bend the actuator
rod as illustrated
to the left.
CORRECT BENDS
Carefully pry interior
panel off of the door with
a flathead screwdriver.
Actuator rod
Factory rod
Set screws
figure 1
figure 3
INCORRECT BENDS

Check out these great AutoLoc accessories...
REMOTE KEYLESS ENTRY SYSTEM IGNITION SENSOR SWITCH
Relay Sockets
KL550, KL600, KL700,
KL1000, KL1600, KL1800
Take control with Autoloc's new line of remote
keyless entry systems. Aavailable in 5, 6, 7, 10,
16, and 18 channel configurations!
From each of the two included 4 button remote
transmitters you can control just about any eletrical
device you have installed on your vehicle. This
includes: power windows, power door locks,
sunroofs, headlights, dome light, alarm system,
neon graound effects, and much much more!
Each available channel offers programmable pulse
times, allowing you to choose between pulse,
constant, and latching outputs. Each system also
comes with AutoLoc's exclusive shaved door handle
mode which increases efficiency of solenoids and
actuators.
Like all AutoLoc products, all remote keyless entry
systems are easy to install come with a limited
lifetime warranty.
IS1000
Add ignition controlled locking to any power door lock system. This
sensor switch will unlock your doors when the ignition is switched to
the "OFF" position and automatically lock the doors when the ignition
is in the "ON" position. This feature is most ideal for families with
children. The IS 1000 also offers a pulse generator mode which allows
you to create double pulses from a single pulse. Ideal for VWs and
other double pulse locking systems.
RAS12 (pictured)
This heavy duty relay sockets makes your
installation a snap! Simply plug in any
standard 5 pin relay and your ready to go.
RASDUAL
This dual relay sockets makes your installation
a snap! Simply plug in any 2 standard 5 pin
relay and your ready to go.
RASKILL
This heavy duty relay socket offers a built in
diode for easy starter kill wiring. Simply plug
in any standard 5 pin relay and your ready
to go.
30/40 AMP Relay
RA1000
High quality 30/40 amp relay not only make installation easier, it is
sometimes required!
This heavy duty relay is the best choice for any sort of 12-volt wiring
project. It will never get stuck or short out on you. Combine the
RA1000 relays with the RAS relay sockets, and you've just saved
yourself hours of wiring time!
AUTOLOC DOORS CAR DOORS