jablotron Athos CA-1202 User manual

CA-1202 user manual – Mode 3 - 4 / 4 – MHF53501
Internet: www.jablotron.cz
Tel.: [phone]
fax: [phone]
Pod Skalkou 33
466 01 Jablonec nad Nisou
Your installer’s contact details:
CA-1202 user manual – Mode 3 - 1 / 4 – MHF53501
The “Athos” CA-1202 GSM pager
MODE 3
Thank you very much for buying our CA-1202 GSM pager. Now you will always be
able to find where you left your car.
Jablotron Ltd.
1. Alarm
In the case of activation, warning SMS messages will be sent to all
phones (TEL1 to TEL4) and these phones will also be called with a
siren sound1.
2. Remote control by SMS instructions
SMS instructions sent from an authorized phone (TEL1 to TEL4)
can operate the alarm remotely. Factory default instruction texts
are shown in the following table. If an SMS is sent from an
unauthorized phone a valid user code must be entered before
the instruction (e.g. USER IMO).
SMS instruction texts
Default Your text Description
IMO STOP (immobilize) the car (after turning
the ignition key off)
UNIMO Unblock (mobilize) the car
STATUS GSM pager will reply with status
information, e.g. „car reports: Time: 27.01.04
13:04, Status: Armed, Unblocked, Ignition off“.
LOCATOR To obtain the car location from the GSM
provider. 2
HELP The GSM pager will reply with a brief list of
SMS instructions.
CREDIT To obtain the balance of a prepaid SIM
card if used.2
UC xx...x To change the user code. uuuu is the new
user code, up to 8 characters (A –Z & 0 –
9). The factory default user code is USER
Only basic ASCII can be used in the SMS instruction texts.
Ask the installer to edit the SMS commands for you.
After the HELP command, the GSM pager will reply with the factory default SMS instructions.
The instructions that were modified will not be in the reply.
1If it is activated, then in the case of an alarm all calls are automatically answered
(it is possible to listen and speak to the car remotely).

CA-1202 user manual – Mode 3 - 2 / 4 – MHF53501
3. Remote blocking of the car
When the GSM pager receives the SMS command IMO it will reply with a
confirmation SMS and block (immobilize) the engine. If the ignition key is on
when the GSM pager receives the command IMO, immobilization will occur as
soon as the ignition key is switched off which will be confirmed by SMS.
Unblocking the car is only possible by the SMS instruction UNIMO.
4. Car location
If your GSM provider offers a location service you can obtain the location of the
car by just sending the instruction LOCATOR. The GSM pager will reply e.g.
[phone] county: Jihocesky, District: Jindrichuv Hradec, Name: Nova Ves nad Luznici.
Distance 5.4 km. E14*52'1"@N48*50'24" + -200m 15:23:01 18.09.01
The GSM pager can send the location automatically in the case of an alarm or
immobilization by the IMO command2.
5. Phone calls by an installed hands free set
If the HF-03 hands free set is installed, it is
possible to receive and make phone calls via
the GSM pager.
Incoming calls – to answer them, press any
button on the RC-4x remote control. By
pressing any button again, the call will be
terminated.
To make a call – you can call up to 4
preprogrammed numbers while you are
driving. By pressing one of buttons , , or
on the remote control you will dial the
corresponding number (preprogrammed by the installer)
By pressing any button again, the call will be terminated. When armed, all
incoming calls are automatically rejected. If the car is blocked (by the IMO
instruction) all calls are automatically answered (it is then possible to listen to
and to speak to the car remotely).
6. Car battery low voltage reporting
The GSM pager checks the voltage of the car battery. If the voltage is too low
(10V) it will notify users via an SMS message. The GSM pager can be backed up
by a BB-01 battery. Thus, the GSM pager can send SMS messages (but not work)
even when the car battery is disconnected. The manufacturer recommends regular
BB-01 checking once a year. The battery should be replaced every two years.
2Must be set by the installer
CA-1202 user manual – Mode 3 - 3 / 4 – MHF53501
7. Remote service
When it is necessary to change the basic settings of the GSM pager like phone
numbers etc you do not need to contact the installer. Instead it is possible to
change settings remotely.
8. Central monitoring station communication
The GSM pager allows central monitoring via GPRS data protocol. Please ask
your supplier for details.
9. Roaming
If you travel abroad and your SIM card supports roaming, the GSM pager will
work there too (the functions LOCATOR and CREDIT might be not available).
10. LED indicator signals
The LED indicator is used to show
the status of the GSM pager.
Warning! If the LED indicator
starts flashing fast after the
ignition is switched off, it will not
be able to send any messages nor
call in the case of an alarm.
LED state Meaning
permanently ON Connecting to a GSM network
or a phone call
Interrupted light Car was stopped
(immobilization)
Flashing fast GSM network is not available