Avail GLANCE R03A445 User manual

[e-mail] 1300 945 720
AVAIL QUALITY DESIGNS
}Australian Made & Owned!
}Standard Sizes: 45 Degree or 90 Degree
}Scratch resistant high grade stainless steel
}Comfortable 30mm diameter rail
}Rail 150kg capacity and construction exceeds Australian Standard AS1428.1
and is fully approved and independently tested
30mm Diameter Angled 45 and 90 Degree Grab Rail -
45 Degree - R03A445
90 Degree - R03A490
GLANCE
AVAILCARE.COM.AU
PHONE: [phone] | EMAIL: [e-mail]
For mounting the Glance rail onto glass screens we
recommend minimum 10mm thick glass
450
450
AVAIL QUALITY DESIGNS
}Australian Made & Owned!
}Standard Sizes: 45 Degree or 90 Degree
}Scratch resistant high grade stainless steel
}Comfortable 30mm diameter rail
}Rail 150kg capacity and construction exceeds Australian Standard AS1428.1 and is
fully approved and independently tested
30mm Diameter Angled 45 Degree Grab Rail
GLANCE
AVAILCARE.COM.AU
PHONE: [phone] | EMAIL: [e-mail]
For mounting the Glance rail onto glass screens we
recommend minimum 10mm thick glass
450
450
AVAIL QUALITY DESIGNS
}Australian Made & Owned!
}Standard Sizes: 45 Degree or 90 Degree
}Scratch resistant high grade stainless steel
}Comfortable 30mm diameter rail
}Rail 150kg capacity and construction exceeds Australian Standard AS1428.1 and is
fully approved and independently tested
30mm Diameter Angled 45 Degree Grab Rail
GLANCE
For mounting the Glance rail onto glass screens we
recommend minimum 10mm thick glass
450mm
450mm

[e-mail] 1300 945
720
GLANCE RAIL
INSTALLATION INSTRUCTIONS
1. Locate wall studs, install into at least one stud.
(minimum 2 screws per bracket).
2. Place rail on wall over centre of stud and mark hole positions
on wall through the holes of mounting bracket.
3. Drill pilot holes into wall stud t osuit mounting screws and
place silicon in holes to seal out moisture.
4. Install rail by screwing onto wall, minimum 2 screws in
each mount bracket (1 at top side, 1 at bottom side, use
appropriate mounting screws for the wall stud material,
supplied screws are for timber wall studs).
5. Push cover plates over mounting brackets until they cllip on.
CONTENTS:
2 x Wall Seal
6 x Stainless Screws
1 x Grab Rail
WARNING:
These rails are designed to be mounted onto wall studs or masonry walls. Installation is
recommended to be completed by qualified tradesperson who complies with the AS 1428.1-
2009 Design for Access and Mobility standard. It is recommended rail location is determined
by a qualified Occupational Therapist or trained professional to the AS 1428.1-2009 standard.
Correct installation is required to ensure safe, long term operation. Incorrect mounting can result
in reduced capacity of the rail which can result in injury to user and damage to the wall.
AVAILCARE.COM.AU
PHONE: [phone] | EMAIL: [e-mail]
AVAILCARE.COM.AU
PHONE: [phone] | EMAIL: [e-mail]
GLANCE
INSTALLATION INSTRUCTIONS
1. Locate wall studs. Install into at least one stud. (minimum 2 screws
per bracket)
2. Place rail on wall over centre of stud and mark hole positions on wall
through the holes of mounting bracket.
3. Drill pilot holes into wall stud to suit mounting screws and place
silicon in holes to seal out moisture.
4. Install rail by screwing onto wall, minimum 2 screws in each mount
bracket, (1 at top side, 1 at bottom side, use appropriate mounting
screws for the wall stud material, supplied screws are for timber
wall studs)
5. Push cover plates over mounting brackets until they clip on.
WARNING:
These rails are designed to be mounted onto wall studs or masonry walls. Installation is recommended
to be completed by qualified tradesperson who complies with the AS 1428.1-2009 Design for Access and
Mobility standard. It is recommended rail location is determined by a qualified Occupational Therapist or
trained professional to the AS 1428.1-2009 standard. Correct installation is required to ensure safe, long
term operation. Incorrect mounting can result in reduced capacity of the rail which can
result in injury to user and damage to the wall.
Wall Bracket
Wall Screw
Cover Plate
CONTENTS:
2 x Wall Seal
6 x Stainless Screws
1 x Grab Rail
8
19
56
WALL BRACKET
AVAILCARE.COM.AU
PHONE: [phone] | EMAIL: [e-mail]
AVAILCARE.COM.AU
PHONE: [phone] | EMAIL: [e-mail]
GLANCE
INSTALLATION INSTRUCTIONS
1. Locate wall studs. Install into at least one stud. (minimum 2 screws
per bracket)
2. Place rail on wall over centre of stud and mark hole positions on wall
through the holes of mounting bracket.
3. Drill pilot holes into wall stud to suit mounting screws and place
silicon in holes to seal out moisture.
4. Install rail by screwing onto wall, minimum 2 screws in each mount
bracket, (1 at top side, 1 at bottom side, use appropriate mounting
screws for the wall stud material, supplied screws are for timber
wall studs)
5. Push cover plates over mounting brackets until they clip on.
WARNING:
These rails are designed to be mounted onto wall studs or masonry walls. Installation is recommended
to be completed by qualified tradesperson who complies with the AS 1428.1-2009 Design for Access and
Mobility standard. It is recommended rail location is determined by a qualified Occupational Therapist or
trained professional to the AS 1428.1-2009 standard. Correct installation is required to ensure safe, long
term operation. Incorrect mounting can result in reduced capacity of the rail which can
result in injury to user and damage to the wall.
Wall Bracket
Wall Screw
Cover Plate
CONTENTS:
2 x Wall Seal
6 x Stainless Screws
1 x Grab Rail
8
19
56
WALL BRACKET