AVGO NN43A User manual

.
MODEL NO.:NN43A

TABLE OF CONTENTS
Instructions
37
Media
Media
TV Bracket assemble
TTS Function Operation
DVD Setup
DVD Setup
38 39
40
41
42

FCC Declaration or Conformity Compliance statement
(Part 15):
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation. The party responsible for
compliance to these rules is:
Bluestem Brands Inc.
7075 Flying Cloud Drive Eden Prairie, MN 55344
PH：952-626-3824
Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable
parts inside. Refer servicing to qualified personnel.
1)No naked flame sources, such as lighted candles, should be placed on the apparatus.
2)Attention should be drawn to environmental aspects of battery disposal.
3)Use of the apparatus in moderate climates.

Instructions
a tip-ov er and/or injury.

EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE
ANTENNALEADIN WIR E
ANTENNA
DIS CHAGRE UNIT
(NEC SECTION 810-2 0)
GROUNDIN G CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVIC E GROUNDING
ELECTRODE SYSTEM
(NEC ART 250,R ARTH)
GROUND
CLAMP
ELEC TRIC SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
26)
designed in such a way that it does not require a safety connection to electrical earth.
27) Correct disposal of this product. This marking indicates that this product should not
be disposed with other household waste. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources.
This equipment is a Class II or double insulated electrical appliance. It has been
Instructions
4
28)The ventilation should not be impeded by covering the ventilation openings with items
such as newspaper, table-cloths, curtains etc.
29)WARNING: The batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, fire or the like.
30)WARNING: The mains plug is used as disconnect device, the disconnect device shall
remain readily operable.

Warning: batteries(pack or batteries installed) should not be exposed to excessive heat
such as sunshine, fire or other heat sources.Please do not mix new battery and old battery
for recycle using.
Instructions
5

Instructions
have bright spots/pixels.
6

10cm
10cm
below
Instructions
Note: Drawing is a representative example only
operat e
To avoid damage to the TV, place the TV on a table, face down on a soft surface.
the
7

Fix the TV on the wall
1.First,put the TV on the table smoothly and put some soft cloth on the table to avoid
getting scratched the screen.
2.Use a screw driver to take off the screws which are fixed on the bottom stand
(the direction of the arrow, refer to the photo1).please be careful when tating off the
bottom stand).
3.Make one bracket which can fix on the wall according to the size of arrow direction
of photo2 and photo3.
4.Drill four holes properly on the wall (the size only for reference) and put into four
screws.(optional parts)
5.according to the step 4,use the screwdriver to lock the screw on the back of the TV.
then hang the TV on the wall.
Note:
1.The bracket fixed on the wall is optional part.
2.when you assemble the TV, there should be no other articles on the around and front
and please keep the distance from other articles.
3.When assemble the TV, please ask the professional worker to fix in order to avoid
the danger.
4.The fixing picture is only for reference.
5.Please follow the user’s manual about bracket assemble to fix the TV.
6.Attach the mounting bracket with the VESA compatible wall mounting kit.
8
TV Bracket assemble
A
B
D
C
quantity
4
Product family Inches Standard screw
(C*D)
Specifications
VESA(A*B)
LED TV 24 10cm x 10cm M4*L6
Wallmounting Installation
Note: "D" is the effective length of the screw in the mounting hole.
The figures and illustrations in this manual are provided for reference only
and may differ from their actual appearance. The product design and
specifications may change without notice.

TV Buttons and Connections
TV Buttons
Note: The following is only a representation of the buttons on your unit. The actual
position and arrangement of the buttons may differ by model.
:Turn ON/OFF Power.
SOURCE:External Signal Input Selection.
MENU:Display Main MENU And Confirm MENU Item Selection.
CH+/-:Select Channel.
VOL+/-:Adjust Volume.
Connections
AV input
External AV Signal Input and
Right/Left Audio Inputs.
AV Output
Right/Left Audio Outputs.
External AV Signal Output and
Component Input
Connect to a component output
connection on your external device.
HDMI Input(HDMI1,2,3)
Connect to a HDMI output
connection on your external device.
ANT 75/RF Connection
Connect to the antenna/cable TV
output of your device or wall plate.
VGA Input
Connect to your PC using a VGA
cable(not provided).
PC Audio Input
Connect to your PC Audio Out
using 1/8 line cord.
HEADPHONE JACK
Plug earphones into jack for private
listening. Overrides speakers.
USB Input
Connect to your USB device.
COAXIAL Output
Connect to your SPDIF device
Output
Audio Out Right/Left
Connect to your external device.
OPTICAL
Digital Audio Output.
Y Pb Pr
INPUT
VIDEO R L
OUTPUT
VIDEO R L
INPUT
OPTICAL
OUTPUT
RL
COAXIAL
HDMI
HEADPHONE
9

5V 0.5A
10

Install and Connect TV
TV ANT
FM ANT
TV signal output
Setup your TV
1.Put your TV in a place that can bear the
weight of the TV.
To avoid danger, please do not assemble
the TV near water or extreme heat(such
as a furnace, light source,or candle.)
Do not block the ventilation on the back
of the TV.
Connect signal source and power
2. Connect the antenna cable to the RF
connection on the back or side of the TV,
and/or the signal source HDMI cable to the
HDMI input(s) on the rear or side of TV. Plug
the TV into the wall power outlet (AC120 ~ 60Hz).
1
3
Turn on the TV
3.While in standby mode the power indication
light will be red.Press the power button on
the TV or remote control.The light will change
to green.
Note:
Picture for reference purposes only.
2
TV Feet Installation Instructions
1.Open the carton and remove the TV,
accessories, and the stand/feet.
2.To avoid damage to the TV, place on
a table, face down on a soft surface.
The feet are attached to the
TV with the provided screws.
3.Ensure all feet screws are tightened securely.
Do not overtighten.
Your TV will have either a Feet.
Assemble accordingly.
11

12
Select TV Configuration
TV Configuration
If your preferred language is French or Spanish, exit this Setup Wizard by pressing the Menu
button, and follow the instruction on page 19 to make your language selection and re-enter the
Setup Wizard from that Menu screen.
Setup Wizard
Connect a RF cable from your incoming antenna/cable jack to the TV’s input labeled “ANT”,
and/or a HDMI cable from your signal source to the HDMI input jack.
on the remote
Home Mode(Energy Saving):Select Home Mode to maximize energy efficiency.Please note if you select Home
Mode,the picture will be darker . This mode meets the requirements of ENERGY STAR® qualification .
Retail Mode: Select Retail Mode if you would like your picture to be brighter. At times this mode may use more
energy to operate the Volume/Sound Mode and the picture Mode.In this setting,the power consumption may
possibly exceed the limitted requirement of the ENERGY STAR® qualification .
ENERGY STAR® is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).
ENERGY STAR® is a joint program of U.S. Environmental Protection Agency and the U.S. Department of
Energy helping us all save money and protect the environment through energy efficiency products and
practices.
This product meets ENERGY STAR® guidelines for energy efficiency. ENERGY STAR® and
the ENERGY STAR® mark are registered U.S. marks . ENERGY STAR® is a registered mark
owned by the U.S. government.

Cable
Analog : 0
Digital : 0
RF CH : 10
Total Found: 0
on the remote (Air/Cable).
on the remote
13

14

/ Power saving
Press ▼ / ▲ button to select among Picture Mode /Brightness/ Contrast / Color / Tint / Sharpness /
Advanced Settings. Color Temperature/
Power saving Lower power consumption.
. The shadow of the picture cannot be adjusted.
15

Return
Move Select
16
Middle
Middle

17

pref erence.
W
Default is off.
18

butt on to select among Sleep Timer / Time Zone / Daylight Saving Time /
Time Form at / Auto Clock / Clock.
Pre ss ▼ / ▲
Pre ss to ente r. ENTER / ▼
Pre ss button to adjust.◄ / ►
ENU again or back to parent menu. Pre ss M
19