Avitec 110100 User manual

Read and understand this entire manual before assembling,
installing, operating, or servicing this product.
SAVE THIS MANUAL
Copyrightc2023 by AVITEC. All rights reserved. No portion of this manual or any artwork contained
herein may be reproduced in any shape or form without the express written consent of AVITEC. Due
to continuing improvements, actual product may differ slightly from the product scribed herein. Tools
required for assembly and maintenance may not be included.
Instruction Manual
&
Parts List
Bike Repair
Stand
Model 110100

IMPORTANT SAFETY
INFORMATION
This is a SAFETY ALERT symbol.
It is used to alert you to
potential personal
injury hazards. Obey all
safety messages that follow
this symbol to avoid possible injury or death.
DANGER indicates a
hazardous situation which, if not avoided,
will result in death or injury.
WARNING indicates a
hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION indicates a
hazardous situation which, if not avoided,
could result in minor or moderate injury.
NOTICE indicates
important information which, if not followed,
may cause damage to equipment.
SAVE THIS MANUAL
Keep this manual for the safety warnings
-
tant information on how to assemble, use
and maintain this product.
Write the product’s model number and
purchase date on the cover page of this
manual.
Keep this manual (and your purchase re-
ceipt) in a safe place.
UNPACKING
The shipment should be thoroughly inspected as
soon as it is received. The signed “bill of lad-
ing” is acknowledgement by the carrier of receipt
in good condition or shipment covered by our
invoice. For your own protection, if any of the
goods called for on the bill of lading are shorted
or damaged, do not accept them until the carrier
makes a notation on the freight bill of the shorted
or damaged goods. Notify AVITEC
immediately if any hidden loss or damage is
discovered after receipt.
DANGER
WARNING
CAUTION
NOTICE
INSTRUCTION
MANUAL
WARNING concerning Risk of Eye
Injury. Wear ANSI approved eye
protection.
WARNING concerning Risk of
Hearing Loss. Wear hearing pro-
tection.
IMPORTANT SAFETY
INSTRUCTIONS
1. Read and understand all
safety warnings and in-
structions. Failure to follow the warnings
and instructions may result in serious injury
or death. Save all warnings and instructions
for future reference.
2. Personal and Work Area Safety
A. Always wear ANSI approved
safety goggles.
B. Always wear hearing protec-
tection when working in
noisy environments. Prolonged exposure
to high intensity noise can cause hearing
loss.
C. Use safety equipment. Safe-
ty shoes, hard hat and work
gloves must be used for applicable condi-
tions.
Model 110100 Page 2
Model 110100
Page 3
D. Dress appropriately. Never wear loose
Contain long hair, and keep hair, clothing
and gloves away from moving parts.
E. Use common sense when working.
Stay alert and concentrate when assembling
and using the Bike Repair Stand. Never
drugs or medications.
Personal and Work Area Safety (continued)
F. While assembling and setting up the
Bike Repair Stand keep work area clean
and well lighted. Keep spectators and
children out of the work area.
3. Use of the Bike Repair Stand
A. Do not modify this product and do not
use this product for purposes that it was not
designed for.
B. This product is designed to support a
bicycle while bicycle service and main-
tainence is being performed. The Bike
Repair Stand is height and angle adjust-
able, making it easy to position the bi-
for working.
The maximum weight capacity of the Bike
Repair Stand is 66 Lbs. Do not exceed
this capacity.
C. The Bike Repair Stand must be set up
done in an area where people or vehicle traf-
D. This product is not
a toy and should be located in an area away
from children and out of reach of children.
Do not allow children to play with this prod-
uct. It should not be climbed on or used to
restrain children or animals.
E. Some product assembly is required. If
you are not experienced or capable of do-
ing this type of work safely, the Bike Repair
technician.
F. Before each use, make sure that the Feet
Stand with a solid posture. The bottom of
-
face. Use the Lock-down Clamp to tighten
and secure the Leg Assembly. The ground
G. It is recommended that an assistant help
in lifting the bicycle and securing the bicycle
to the Clamp, as well as when removing the
bicycle from the Stand.
H. Take precautions
when loading the bicycle on the Bike Repair
bicycle. If appropriate, use extra padding to
-
bing against the Stand.
I. Never attempt to sit on the bicycle while it
is being supported by the Bike Repair Stand.
Never work underneath the bicycle while it is
supported on the Bike Repair Stand.
J. Before each use, check the overall condi-
tion of the Bike Repair Stand. Make sure
that all components are assembled properly.
Make sure Clamps are tightened down and
all hardware is tightened.
K. It is the responsibility of the owner of this
product to make sure that everyone using the
Bike Repair Stand reads and under-stands
the warnings and instructions con-tained in
this instruction manual.
L. AVITEC is not responsible for any damage
to the bicycle occuring while the bicycle is
being supported by the Bike Re-pair Stand.
M. Save packaging information, warnings
and this manual. They contain important in-
formation and must always remain readable.
Contact AVITEC for replacements.
Keep in mind that the warnings previous-
ly discussed cannot cover all possible
conditions or situations that could occur.
It is important that the person setting up
and using this product understand that
common sense and caution are factors
which cannot be built into this product,
and must be supplied by the person(s)
using this product.
WARNING
NOTICE

Limited Warranty
AVITEC warrants to the original retail
purchaser that the product is free of defects
in material and workmanship at the time of
shipment. This Bike Repair Stand is
warranteed for 90 days from the date of
purchase. This warranty is expressly in lieu
of all other warranties, express or implied.
Proof of purchase is required for warranty
transactions; a copy of the original invoice
or sales receipt is required.
Setting Up and Using
the Bike Repair Stand
Always wear ANSI approved
safety goggles.
Refer to the photos on this page.
A. Read all Personal and Work Area Safety
Warnings on pages 2 and 3 before setting up
and using this product.
B. Some assembly is required. Start with
Lower Leg Assembly. Grip the Lower Tube
and push down on the Lower Leg Assem-
bly to open up the 3 Legs. Make sure tip
of Lower Tube slides through the Mounting
Bracket of Lower Leg Assembly (see photos
below).
C. Assemble Upper Tube to the top of the
Lower Tube and lock in place by fully rotat-
ing Clamp Lock (see photo below).
D. Slide tubing section of Clamp through
upper mounting bracket of Upper Tube.
Note: Clamp Lock can be turned clockwise
to tighten. Once securely tightened, then ro-
tate Clamp Lock handle to lock in place (see
photo above).
E. Attach the Tool Tray to the Lower Tube
(suggested location: see photo on Page 1,
and photo below), using a hex wrench (not
included) to secure the 2 hex screws.
F. With assembly complete, make any
needed adjustments to Lower Leg Assembly,
and Clamp assembly to meet your work re-
quirements and the size of the bicycle. Note
the mounting hole in each Foot; Feet can
(see photo).
When drilling holes for mounting hardware,
make sure that there are no hidden wires or
cables in the drilling path.
Model 110100 Page 4
Note: Some parts are listed and shown for illustration pur-
poses only; no replacement parts are available.
Manufactured for and distributed by:
Avitec Towing and Garage Equipment
Camarillo, CA 93012, U.S.A
www.avitecusa.com
Customer service hours 9:00 am-4:00 pm, Monday-
Friday, PST., 1-805-385-9888
Maximum Weight
Capacity
66 Lbs.
Clamp Head Rotates 360 de-
grees
Working Height Adjusts from 40”
to 75”
Overall Weight 17.6 Lbs.
SPECIFICATIONS
Model 110100 Page 5
Fully rotate
Clamp
Lock
handle to
secure
Lower Leg
Assembly
in place.
Lower Tube
Lower Leg
Assembly
Mounting
Bracket
Lower Tube
Clamp Lock
Upper
Tube
Turn to
tighten
Handle
down
to lock
Clamp
Tool Tray is mounted
around Lower Tube.
Mounting
Hole
G. Before lifting the bicycle onto the Bike
Repair Stand, make sure the Stand is locat-
that all Clamp Locks are tightened down.
Make sure the bicycle does not exceed the
maximum weight capacity of 66 Lbs.
H. With assistance, as needed, lift the up-
per bicycle frame into the Clamp as shown
in photo below. Make sure the bicycle is
balanced properly. Close the Clamp Lock
to secure the bicycle in place (see photos
below).
I. Use the Wheel Brace to prevent move-
ment of the front bicycle wheel while work is
being done.
Connect one end of Brace to the tire (us-
ing rubber stretch tie) and the other end to
Stand’s Upper Tube. The length of Wheel
Brace is adjustable (adjustment screw in
center). See photo below.
WARNING
Maintaining the Bike Repair Stand
A. The general condition of this product
should be checked periodically. Make sure
that the Clamp and all Clamp Locks func-
tion properly. Make sure that all hardware is
tight. Make sure that the Lower Leg Assem-
bly is structurally sound.
B. Keep the product clean and free of
grease.
product.
Bike Frame
Bike Frame
Clamp
Open Clamp
Closed
Wheel
Brace
Tool Tray
Connect