AWM Humanscale M10 User manual

Desk Mount
Assembly Instructions
North America: [phone]
Europe: [phone]
Asia Pacific: [phone]
EN
FR
ES
IT
DE
NL
9
11
14
16
19
2
North America: [phone]
Europe: [phone]
Asia Pacific: [phone]
EN
FR
ES
IT
DE
NL
10
13
16
19
22
2
awm.net.au [email protected]
1300 475 217

2
Ζ
Ι
ΜΞ
Ο Π
Ν
Η
Κ
Θ
Λ
Bolt-Through Plate
3 Crossbar Link Screws4mm Hex Key
8 mm Hex Key Bolt-Through Bolts
Bolt-Through Mount
Sliding Desk Mount Clamp Mount
Crossbar Installation Hardware
4 Standard VESA Bracket
Screws
4 Plastic Spacers
4 Extended VESA Bracket
Screws
VESA Bracket and Cover
5mm Hex Key
NOTE: 4mm and 5mm Hex Key can
be found under the plastic base cover.
INSTALLATION HARDWARE
Ρ΢

3
Ζ
Η
Assembly Instructions
Attach Mount To Work Surface
Clamp Mount
NOTE: There are two sets of Bracket Screw holes to
accommodate the thickness of every work surface. Use the
upper holes for surfaces up to 1.8” (48mm) thick and lower
holes for surfaces up to 2.7” (68mm) thick.
A - For installation on open edge of work surface:
1Slide Mount (A) against work surface edge and fully tighten
Clamp screws(B) with 5mm hex key (C).
B - For installation on work surface positioned against a
wall or panel:
NOTE: This method can also be used to mount through
grommet holes wider than 3”
1Detach the Bottom Clamp (D) from the Top Bracket (E) by
loosening Bracket Screws (F) with 5mm hex key.
2Position the Top Bracket against work surface edge.
3Underneath the work surface, reattach the Bottom Clamp
to the Top Bracket using the Bracket screws.
4Fully tighten the Clamp Screws (G) with 5mm hex key.
NOTE: Clamp Mounts cannot be used to mount the M10
to any vertical surface.
Sliding Desk Mount
C - For installation on a desk with minimal clamp clearance:
1 Remove Base Cover.
2 Loosely attach Clamp Bracket (H) to base with three
included screws (I). The screws should not be tightened all
the way.
3 Slide the base and clamp over the back edge of the work
surface until the clamp rests on the edge.
4 Fully tighten the three clamp screws to secure the base to
the work surface.
Θ
A
B
C
E
D
F
G
I
H

4
BOLT-THROUGH MOUNT
D - For installation on work surface with no access for clamp system:
1 Drill 1/2” hole through work surface in desired location.
NOTE: Bolt-Through Mount can accommodate a hole up to 4” (102mm)
in diameter. If hole is 2” (51mm) or more, cables can be routed through
the hole. For some 2”grommet holes, cables should be routed before
installation of mount to accommodate cable plugs (cable access is
approximately 1.5” x 0.25” with 2” grommets).
2 Position the M10 Base over the work surface hole (J).
3 Align Bolt-Through Plate, foam side up, under the work surface. Pass
the Bolt (K) through the hole in the plate and screw into M8 base by
using 8mm hex key (L).
In each arm connection, there is an adjustable Smart Stop Ring which can be
positioned to limit the arm’s range of motion. Depending on the orientation
of the ring the arms can be set to rotate either 90°, 180°, or 360°. The marked
angle will be in the center of the range of motion.
Arm can rotate
without stopping
Arm can rotate 180˚
Arm can rotate 90˚
Smart Stop Adjustment
J
J
KL
Ζ
Ι
Η
Κ
Θ

5
Ζ
Ι
Κ
Θ
B
NOTE: Before adding each link, adjust the smart stop (A)
according to step 2. The links should be positioned so that
the monitors do not extend beyond the desk surface.
1 Insert the angled link into the mount until release
button locks in place.
2 Insert the dynamic link into the angled link until the
release button locks in place.
3 To remove links, press the release button (B) and lift
upward near the joint.
If using dual monitors, attach the crossbar according to the
following steps. If using triple monitors, use the instructions
included with the triple crossbar. If using a single monitor,
continue to Step 5.
1 Attach crossbar (A) to crossbar link (B) using crossbar link
screws (C). Tighten with 4mm hex key until secure.
2 (Optional) Attach handle (D) to crossbar by using included
screws (E). Adjust the handle to desired height. Tighten
with 4mm hex key until secure.
WARNING: Risk of Injury - Do not allow crossbars to be
positioned so that the monitors extend beyond the work
surface which the mount is installed to at all times.
Attach Arm To Base Stem
Attach Crossbar To Arm (Dual-Monitor Application Only)
A
A
B
C
D
E
A
Η

6
Attach Vesa Bracket To Monitor
1 Separate the VESA cover from the VESA bracket.
2 Position the VESA Bracket over the mounting holes
on the back of monitor with the D-shaped cutouts in
a vertical orientation. Attach using the 4 VESA screws
provided.
3 Snap the VESA cover back in place.
The VESA Bracket features 75mm and 100mm hole
patterns.
If you need to oset the Bracket from the monitor use the
provided
Extended VESA screws and Plastic Spacers. You may also
use the screws that came with your monitor.
Attach Monitor To Arm
1 Hold the monitor angled back and lower it onto the arm. Fit the hook at the top of the
arm into the corresponding cutout in the VESA Bracket.
2 Tilt the monitor back upright until the Quick Release Tab (B) on the arm snaps into position.
3 To remove the monitor, lift the Quick Release Tab and pull the bottom of the monitor away
from the arm, then lift free of the hook.
Large/curved monitors require adjusting the tension screw (A)
Clockwise until the monitor holds in position. (approx. 35 in-lbs.)
A
B
Ζ
Η

7
Ζ
Η
Weight Adjustment
Your monitor should move up and down easily and stay in place once
adjusted. If it is dicult to adjust or moves without assistance, it is
not properly counterbalanced.
M10 Arm - Total Weight Range: 20-48 lbs. (9-21.7 kg)
Single Monitor - Max weight: 48 lbs. (21.7 kg)
Dual Crossbar - Max weight per monitor: 12.5 lbs. (5.6 kg)
Triple Crossbar - Max weight per monitor: 10 lbs. (4.5 kg)
1 To access the Adjustment Screw (D), use your finger to
pry open the Cover (C) on the Upper Arm Link (B).
2 Using the 5mm Hex Key turn the Adjustment Screw (D)
clockwise to increase the load tension, and counter-clockwise
to decrease the load tension. Turn the Adjustment Screw (D)
until the Monitor is properly balanced.
3 Move the monitor around to ensure that the motion is smooth
and the arm functions as intended and holds the monitor in
place.
4 Reposition the Cover (C) and press until it snaps into place.
CAUTION: Do not over tighten the screws as it can damage the
screw head or threads.
A
B
After the monitors are installed on the crossbar, there may be a small height dierence between them.
To align the monitors, use the adjustment screw located on top of the monitor tilt.
1 To raise a monitor, turn the screw clockwise. To lower, turn counter clockwise.
2 (Optional) Attach handle (D) to crossbar by using included screws (E). Adjust the handle to desired
height. Tighten with 4mm hex key until secure.
Leveling The Monitors (Dual-Monitor Application Only)
D
C

8
C
D
B
A
Ζ
Ι
Η
Κ
Θ
Cable Management
1 If using multiple monitors, first route the
cables through the plastic cable clips on the
front of the crossbar. If using a single monitor,
skip to step 2.
2 Route power and monitor cables through the
flexible cable clips on the M10’s upper link
(B).
NOTE: Leave enough slack in the cables to allow
arms to rotate without diculty.
3 Slide the plastic cover (C) on the lower link
upward to remove.
4 Using the two cutouts (D) as guides, run the
cables over the lower link cover.
5 Lift the cover and cables up to the lower link,
making sure that the cover sits flush with the
surface of the arm.
6 Slide the cover down the arm to lock in place,
then gently pull the cables through the arm to
remove excess slack.
CAUTION: Don’t insert extension cords. Don’t
insert any cord connecting one workstation to
another.
Λ