B-Tech BT8341 Instruction Manual

B-TECH AV MOUNTS
www.btechavmounts.com
BT8341
UNIVERSAL POP-OUT VIDEOWALL
MOUNTING SYSTEM
INSTALLATION GUIDE & PARTS LIST
This Pack Contains 1 Videowall Mounting System
PLEASE KEEP THIS FOR FUTURE REFERENCE
• Modular mounting system designed for screens
up to 50kg (110lbs)
• Suitable for landscape or portrait mounting (minimum
screen size is 39" when used in landscape orientation)
• P
ush to open / push to close system provides quick and
easy service access
• Depth to wall: 104mm
•
Tool-less micro-adjustment including lateral
adjustment for seamless
alignment of the screen display
• Height adjustment +/- 25mm
• Depth adjustment +/- 10mm
• Safety screws help prevent unauthorised removal of screens
•
Includes an optional pop-out prevention mechansim
• All mounting hardware included
FEATURES
50kg
INSTALLATION TOOLS REQUIRED
CONTENTS
Installation Safety Notes...................................................................................................... ...............2
Parts List.............................................................................................................................................4
Installation Notes................................................................................................................................6
Installation Instructions........................................................................................................................8
Product Dimensions..........................................................................................................................18
B-Tech Contact Details.....................................................................................................................20
TM
Drill Pencil Level Stud finder
(optional)
Crosshead
screwdriver
Configurations may differ from the ones
shown in this installation manual
10mm (7/16")
masonry bit or
6mm (1/4") wood bit
PER SCREEN

INSTALLATION SAFETY INSTRUCTIONS
2
CAUTION: This mount is intended for use
only with the maximum weights indicated. Use with
flat screens heavier than the maximum indicated may result
in instability causing possible injury.
Do not attempt to install this product until all instructions and warnings have been read and properly understood.
Please keep these instructions for future reference.
Please check carefully to make sure there are no missing or defective parts - defective parts must never be used.
B-Tech International Limited, its distributors and dealers are not liable or responsible for damage or injury
caused by improper installation, improper use or failure to observe these safety instructions. In such
cases, all guarantees will expire.
General
B-Tech International Ltd recommends that a professional AV installer or other suitably qualified person
install this product. Great care must always be taken during installation as most AV equipment is of a
fragile nature, possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely, then please
consult a professional for advice and/or to install this product for you. Failure to mount this product
correctly may cause serious injury or death both during installation and at any time thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing.
This weight limit will be clearly stated on each product and its packaging and will vary from product to product.
Product location
Please pay careful attention to where this product is located. Check load capacity of wall prior to installation
as some walls are not suitable for installation. Designed for indoor use, this mount is suitable for public or home
installation. If located in a public or frequently populated area ensure that the product is out of the immediate
reach of people. If any AV equipment is to be suspended over the likely path or location of people then great
care should be taken to secure all parts of the installation from falling. If you install this product on drywall it
must be securely fixed to a wooden stud, concrete block or other permanent structure behind the drywall board.
Installing on drywall boards alone will not support the weight of most AV equipment.
When drilling holes in walls it is essential to avoid contact with electrical cables and water or gas pipes
contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended.
Only drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all wall fixing screws be used where supplied and that the purpose of all
other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be
supplied to accommodate different models of equipment and set up configurations.
The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation.
If any fixing screws or included hardware are deemed not sufficient for a safe installation then please
consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features that the product might
provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the
product can do so unhindered by any cabling.
Some products have moving parts and the potential to cause injury through the crushing or trapping of
fingers or other body parts.
Particular attention to the nature of moving parts is required especially when assembling installing and
adjusting during set up.
Immediately after installations double-check that the work done is safe and secure. Double-check all
necessary fixings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its fixing points are made as frequently as
possible to ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably
qualified person.

BT8341
PARTS LIST
4
BT8390-EXT
OPTIONAL
MOUNTING RAIL
EXTENSION KIT
5
6
3
2
1
8
7
Due to the multiple installations available the quantity for
each option below is dependent on the mount ordered.
9
11
10
4
OPTIONAL
INTERFACE ADAPTOR ARMS
BT7564 BT7565 BT7566
18
17

1
2
3
4
7
8
9
10
11
12
13
14
15
16
A1
A2
5
6
A1 A2
EXTENSION KIT (OPTIONAL)
INTERFACE ADAPTOR ARMS (OPTIONAL)
WALL FIXING KIT
WALL FIXING KIT
SCREEN INTERFACE KIT
SCREEN FIXING KIT
MOUNTING RAIL
RAIL FIXING KIT
Due to the multiple installations available the
total quantity for each part is dependent on
the mount ordered.
PLEASE KEEP THIS FOR
FUTURE REFERENCE
LEFT INTERFACE ARM
RIGHT INTERFACE ARM
5AF HEX KEY
4AF HEX KEY
ADJUSTABLE BRACE
M5 x 6mm SCREW
M6 x 35mm SCREW
3AF HEX KEY
1
1
1
1
1
1
2
2
M6 x 16mm SCREW
M6 x 25mm SCREW
M6 x 40mm SCREW
WASHER
M8 x 16mm SCREW
M8 x 25mm SCREW
M8 x 40mm SCREW
5mm SPACER
13mm SPACER
24mm SPACER
4
4
4
4
4
4
4
4
4
4
1
2
6
2
2
1
WALL PLATE
M8 SLIDING NUT
M8 x 12mm CSK SCREW
ST8 x 45mm CSK WOOD SCREW
Nº.10 WALL PLUG
5AF HEX KEY
16
15
14
12
13
2
4
ADAPTOR ARMS
M8 x 12mm SCREW
17
18

EXTENDING THE MOUNTING RAIL
Optional: Combining Mounting Rails using the BT8390-EXT
To extend the length of the Menu Board, use the BT8390-EXT to combine mounting rails
6
GRUB SCREW
5
BACK FRONT
GRUB
SCREW
JOINING
BAR
BT8390-CFK
Joining Bar assembly
7
i. On one side of the mounting rail (part 5) insert 4 x joining bars (part 7) half-way into
each slot. On the back side of the rail, insert 2 x joining bars into the middle slots
ii. Loosely fasten the 2 grub screws on each joining bar fixing it to the mounting rail.
iii. Slide another mounting rail (part 5) onto the joining bars and tighten all the
grub screws, combining the rails securely.
5
7
5
8
5
5
78

INSTALLATION INSTRUCTIONS
1Insert Sliding Nuts
i. For each wall plate (part 1) used, insert 2 x M8 sliding nuts (part 3) into the
mounting rail (part 5). One in the top slot and one in the bottom slot.
7
2
BT8390-WFK1 ASSEMBLY
5
2
5

1
con...
Attach Wall Fixing Kit to Mounting Rail
ii. Attach the wall plate (part 1) to the mounting rail (part 5) by fastening M8 x 12mm
screws (part 3) into the inserted M8 sliding nuts (part 2).
8
2pcs for 0 - 2000mm
3pcs for 2100mm - 3500mm
4pcs for 3600mm - 6000mm
5pcs for 6100mm - 8000mm
6pcs for 8100mm - 10000mm
Required quantity of Rail Fixing Brackets
Depth
35mm
2
3
4
BACK
1
5

9
WALL
Installing the mount
i. Determine the centre of the first flat screen at the bottom left.
Mark the centre, for the centre of the rail.
2
A1
158mm
WALL
A2
ii.
ii. Mark and drill two fixing holes for each wall plate (part 1)
assembled. Insert all wall plugs (part A3) and the top
wood screws (part A1). Do not fully tighten - Allow a
gap (approx.10mm).
iii. Hook the wall plate (part A1) on using the keyholes.
Once the rail is hooked on, fasten the wood screws
(part A2) into the bottom holes and tighten all fixings.
WALL
LEVEL
WALL
10mm
1
5
A1

10
Attach Interface Arms to Screen
TOP
BOTTOM
3
Fix the interface arms (parts 9 & 10) to the back of the screens using the screen fixing
kit (parts A-J). Ensure the arms are positioned the correct way round and the same holes
are used on both arms.
Use spacers
(parts H, I & J)
for screens with
recessed fixings.
SCREEN
SCREEN
RECESS
9
10
D
A-G
A-G
H-J
NOTE: Portrait mounting shown.
For landscape mounting attach adaptor arms horizontally
Using Interface Adaptor Arms
BOTTOM
TOP
SCREEN
10
17
18
9

11
Note: Adjustable brace (part 11) is only suitable for horizontal VESA fixings from 400 - 600mm.
4
Connect Interface Arms with the Adjustable Brace
i. Extend the adjustable brace (part 11) and fix at desired length by tightening the 2 screws.
The 3 notches show the position for interface fixings at 400mm, 500mm and 600mm.
ii. Fix the adjustable brace (part 11) to the interface arms (parts 9 & 10) for easy lateral adjustment.
For screens with interface
holes 600mm apart, extend
part 11 to the 600 settting.
11
SCREWS
14
14
12
12
10
9
Distance between interface holes
11
11
12

12
Hook interface arms (part 9 & 10) into the top of the mounting rail (part 5).
Note: For videowall installations, start with the bottom left screen position .
WALL WALL
SCREEN SCREEN
10
9
i. Lateral Adjustment
Slide arms along the mounting rail (part 5) to laterally adjust screen to desired position.
5
Align First Screen
Mount Screen onto Rail
6
5
Lateral Adjustment X Axis

13
HEIGHT ADJUSTMENT HAND WHEEL
Compatible with a 6mm hex key (not supplied)
Height adjustment guides
to help
with accurate
screen alignment
Do not adjust height
past the min and
max guide lines
ii. Height Adjustment (+/-20mm)
Ensure the screen is level and parallel to floor using the
height adjustment hand wheels on the interface arms.
SCREEN
LEVEL
FLOOR

14
iii. Depth Adjustment (+/-10mm)
Ensure the screen corners are equidistant from the wall using the
depth adjustment hand wheels on the interface arms.
SCREEN
WALL
DEPTH ADJUSTMENT HAND WHEELS
Compatible with a 6mm hex key (not supplied)
Depth adjustment guides
to help
with accurate
screen alignment
Do not adjust height
past the min and
max guide lines

15
Work across the video wall 1 column at a time. Hook on screens using a plumb to align.
Use adjustments to ensure screens are aligned.
Note: A 1mm gap between screens should be maintained.
Add Remaining Screens to the Video Wall
7
1mm gap between screens
1mm gap between screens
SCREEN 1
SCREEN 3
SCREEN 2
SCREEN 4
PLUMB
Use Height Adjustment
to align bottom/top of screens
Use Depth Adjustment
to align front of screens
Use Lateral Adjustment
to align sides of screens
WALL

16
1mm gap between screens
1mm gap between screens
WALL
SCREENS
PLUMB
Pop-out screens
for easy access
to
adjustment
hand
wheels
During installation, pop screens out for easy access to adjustment hand wheels
(see Step 6). All screen fronts should be flush.
Secure Interface Arms to Mounting Rails
8
SAFETY
SCREWS
SCREEN
Safety Screw
tightened into
rail
Tighten the safety screws on the interface arms (parts 9 & 10) into the mounting rail (part 5).
16
10
9
5

17
9
SCREENS Push
Push
Servicing Screens
Note: Ensure pop-out function is not disabled (see Step 10).
Push centrally at the left and right of the screen to pop-out the mount.
The screen will rest in the 'open' position for servicing.
WARNING
Be careful not to damage screen when pushing.
Keep hold of screen as it moves outwards.
Screen in service
position
Parts 9 & 10
popped-out
After servicing, push screen back and click into original position.
10
Unlocked Position
20mm
Unlocked Position
Disabling Pop-Out Function (optional)
Locked Position
part 13 fully inserted
13
Do not fully insert part 13 when interface arms are popped out.
To prevent interface arms from popping out, fully insert and tighten the M6 x 35mm screws
(
part 13) at the padlock* symbol at the bottom of the interface arms (parts 9 & 10).
10
9
13 15
13
*

THESE DIMENSIONS ARE INTENDED AS A GUIDE ONLY AND
B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION
18
BT8341
PRODUCT DIMENSIONS
REAR VIEW
FRONT VIEW
BT8390-WFK1
Wall Plate
48mm
90mm
93mm
45mm
186mm
14mm158mm
81mm 24mm
24mm
5mm
2 x Ø
8.4mm
6 x Ø 8.4mm
BT8390-VESA400MAP
Pop-Out VESA 400mm Interface Arms with Micro-Adjustment
Assembled
SIDE VIEW
Distance from
wall 104.4mm
(Tolerance
1mm)
+/-10mm
Depth Adjustment
236.6mm
+/-20mm Height Adjustment
215mm
+/-20mm Height Adjustment
BT8390-VESA400MAP
BT8390-WFK1
BT8390 Rail
Centre of
BT8390 Rail
100mm 200mm 300mm 400mm 426mm
6mm
146.8mm
280mm
65mm
18.8mm
50mm
150mm 250mm 350mm
237.2mm (Tolerance 1mm)
+/-10mm Depth Adjustment
434.4mm
68.7mm (Closed depth)
451.6mm
110.9mm
100.7mm

BT8390-050
19

www.btechavmounts.com
AMA-BT8341-V1.1-0619-BTECH
B-TECH AV MOUNTS
HEAD OFFICE
B-Tech International Limited
Bennett House, Long March, Daventry, Northants., NN11 4NR, UK
Email: [e-mail]
©2019 B-Tech International Design and Manufacturing Limited. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design & Manufacturing Ltd.
B-Tech, Better By Design & System X are registered trademarks of B-Tech International Design & Manufacturing Ltd.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.