B-Tech System X BT8330 Instruction Manual

B-TECH AUDIO VIDEO MOUNTS
www.btechavmounts.com
BT8330
UNIVERSAL MENU BOARD MOUNTING SYSTEM
INSTALLATION GUIDE & PARTS LIST
This Pack Contains 1 Wall Mounting kit
PLEASE KEEP THIS FOR FUTURE REFERENCE
• Universal multi-screen wall mount suitable for
all screens
• Max weight per screen: 50kg
• Suitable for landscape or portrait mounting
• Compatible with B-Tech collars for pole mounting
if required
• Sections can be joined together to increase
menu board width
• Safety screws help prevent unauthorised removal
of screens
• All mounting hardware included
FEATURES
50kg
INSTALLATION TOOLS REQUIRED
CONTENTS
Installation Safety Notes.....................................................................................................................2
Parts List.............................................................................................................................................4
Installation Instructions........................................................................................................................6
Typical Installations..........................................................................................................................14
Pole Mounting Installations......................................................................................................................15
B-Tech Contact Details......................................................................................................................16
TM
Drill Pencil Level Stud finder
(optional)
Drill bitCrosshead
screwdriver
PER SCREEN
This assembly manual covers different installations.
Please note that some parts or procedures shown
may not be required for installation.

INSTALLATION SAFETY INSTRUCTIONS
2
CAUTION: This wall mount is intended for
use only with the maximum weights indicated. Use
with flat screens heavier than the maximum indicated may
result in instability causing possible injury.
Do not attempt to install this product until all instructions and warnings have been read and properly understood.
Please keep these instructions for future reference.
Please check carefully to make sure there are no missing or defective parts - defective parts must never be used.
B-Tech International Limited, its distributors and dealers are not liable or responsible for damage or injury
caused by improper installation, improper use or failure to observe these safety instructions. In such
cases, all guarantees will expire.
General
B-Tech International Ltd recommends that a professional AV installer or other suitably qualified person
install this product. Great care must always be taken during installation as most AV equipment is of a
fragile nature, possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely, then please
consult a professional for advice and/or to install this product for you. Failure to mount this product
correctly may cause serious injury or death both during installation and at any time thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing.
This weight limit will be clearly stated on each product and its packaging and will vary from product to product.
Product location
Please pay careful attention to where this product is located. Check load capacity of wall prior to installation
as some walls are not suitable for installation. Designed for indoor use, this mount is suitable for public or home
installation. If located in a public or frequently populated area ensure that the product is out of the immediate
reach of people. If any AV equipment is to be suspended over the likely path or location of people then great
care should be taken to secure all parts of the installation from falling. If you install this product on drywall it
must be securely fixed to a wooden stud, concrete block or other permanent structure behind the drywall board.
Installing on drywall boards alone will not support the weight of most AV equipment.
When drilling holes in walls it is essential to avoid contact with electrical cables and water or gas pipes
contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended.
Only drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all wall fixing screws be used where supplied and that the purpose of all
other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be
supplied to accommodate different models of equipment and set up configurations.
The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. If
any fixing screws or included hardware are deemed not sufficient for a safe installation then please
consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features that the product might
provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the
product can do so unhindered by any cabling.
Some products have moving parts and the potential to cause injury through the crushing or trapping of
fingers or other body parts.
Particular attention to the nature of moving parts is required especially when assembling installing and
adjusting during set up.
Immediately after installations double-check that the work done is safe and secure. Double-check all
necessary fixings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its fixing points are made as frequently as
possible to ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably
qualified person.

BT8330
PARTS LIST
4
BT8390-WFK1
BT8390-EXT
BT8390-WFK2
BT8390-070
Length: 70cm BT8390-150 Length: 150cm
BT8390-175
Length: 175cm BT8390-200 Length: 200cm
BT8390-VESA400T
BT8390-VESA200T
BT8390-VESA200F
INTERFACE ARMS
BT8390-
VESA400MAF
BT8390-VESA400F
WALL FIXING KIT
MOUNTING RAIL OPTIONAL
MOUNTING RAIL
EXTENSION KIT
A
C
D
B
B2
B1
C2
D1 D1
D1 D1 D1
A1
A1
C3
C1
Due to the multiple installations available the quantity for
each option below is dependent on the mount ordered.
Use only with the
BT8390-WFK2
or

5
PLEASE KEEP THIS FOR
FUTURE REFERENCE
Wall Fixing Kit
Interface Arm Kit
Screen Interface Kit
M4 x 25mm SCREW*
M4 x 12mm SCREW*
M6 x 16mm SCREW
M4 x 40mm SCREW*
M6 x 40mm SCREW
M6 x 25mm SCREW
M8 x 25mm SCREW
M8 x 16mm SCREW
MULTIWASHER*
M8 x 40mm SCREW
13mm SPACER
5mm SPACER
24mm SPACER
1
A1 4
A2 4
A3 4
A4 4
A5 1
A6
PART NAME
REF QTY
PER PACK
WALL FIXING PLATE
ST8 x 45mm CSK WOOD SCREW
No.10 WALL PLUG
M8 SLIDING NUT
M8 x 12mm CSK SCREW
5AF HEX KEY
WALL FIXING KIT
6
C1 24
C2 1
C3
PART NAME
REF QTY
PER PACK
JOINING BAR
M6 x 8mm GRUB SCREW
3AF HEX KEY
EXTENSION KIT
4
A4
B4
C4
D4
E4
F
SCREEN FIXING KIT
REF QTY
PER PACK
4
G4
H4
I4
J4
K4
L4
M
M6 WASHER***
4
N
2
D1 4
D2 1
D3 1
D4
PART NAMEREF QTY
PER PACK
INTERFACE ARM
M6 x 6mm HEX SCREW**
5AF HEX KEY*
5AF LONG HEX KEY**
INTERFACE KIT
1B1 2B2
PART NAME
REF MOUNTING RAIL
END CAP
MOUNTING RAIL QTY
PER PACK
A3
A2
A4 A5 A6
D2 D3
D4
* Not included with the BT8390-VESA400MAF
** Not included with the BT8390-VESA400MAF, BT8390-VESA200F
or BT8390-VESA400F
*** Only supplied with the BT8390-VESA400MAF
Please refer to individual parts list for more information
ABC
F
E
D
GHI
J
KLM
N

EXTENDING THE MOUNTING RAIL
Optional: Combining Mounting Rails using the BT8390-EXT
To extend the length of the Menu Board, use a BT8390-EXT to combine mounting rails
6
B1
B1
C1
C2
C3
FRONT
B1
BACK FRONT
GRUB
SCREW
JOINING
BAR
b. BT8390-WFK2
Joining Bar assembly
B1
BACK FRONT
GRUB
SCREW
JOINING
BAR
a. BT8390-WFK1
Joining Bar assembly Set up for the
BT8390-WFK2
C1
C1
i. On the intended front facing side of the mounting rail (part B1) insert 4 x joining bars (part C1)
half-way into each slot.
ii a. Using the BT8390-WFK1. On the back side of the rail, insert 1 x joining bar in the second
slot and 1 x joining bar in the third slot on the mounting rail.
ii b. Using the BT8390-WFK2. On the back side of the rail insert 1 x joining bar in the top slot
and 1 x joining bar in the third slot on the mounting rail.
iii. Loosely fasten the 2 grub screws (part C2) on each joining bar fixing it to the mounting rail.
iv. Slide another mounting rail (part B1) onto the joining bars and tighten all the
grub screws, combining the rails securely.

INSTALLATION INSTRUCTIONS
1a Insert M8 Sliding Nuts
ai. For each BT8390-WFK1 wall plate used, insert 4 x M8 sliding nuts (part A4)
into the mounting rail (part B1). Two in the top slot / two in the bottom slot.
For the BT8390-WFK2 assembly see page 9.
7
A4
B1
A4 B1
BACK
BT8390-WFK1

1a
Cont... Attach Wall Fixing Kit to Mounting Rail
aii. Attach the BT8390-WFK1 (part A1) to the mounting rail (part B1) by fastening
M8 x 12mm screws (part A5) into the inserted M8 sliding nuts (part A4).
8
2pcs for 0 - 2000mm
3pcs for 2100mm - 3500mm
4pcs for 3600mm - 6000mm
5pcs for 6100mm - 8000mm
6pcs for 8100mm - 10000mm
Required quantity of BT8390-WFK1 or BT8390-WFK2
BT8390-WFK1
BT8390-WFK1
Depth
35mm
A4
A1
A5 A6
B1
Note: BT8390-VESA400MAF interface arms
cannot be used with the BT8390-WFK1
BACK

9
BT8390-WFK2
Depth
49mm
A4 A1
A5 A6
B1
bi. Insert 2 x M8 sliding nuts (part A4) into the second
slot from the top on the mounting rail and 2 x M8
sliding nuts into the bottom slot.
bii. Attach the BT8390-WFK2 (part A1) to the
mounting rail (part B1) by fastening
M8 x 12mm screws (part A5) to the
inserted M8 sliding nuts (part A4).
A4
1b Attach Wall Fixing Kit to Mounting Rail
BT8390-WFK2
BACK

2Fix Mounting Rail to the Wall
Fix the mounting rail (part B1) to the wall using the the wall fixings included with
the BT8390-WFK1 / BT8390-WFK2 (part A1). Once mounted, attach end caps
(part B2) to mounting rail.
10
WALL
Level
A2
B1
A3
B2
A1

11
G
ABCD
FE H
I
3a Attach Interface Arms to Screen
SCREEN TOP
SCREEN BACK
SCREEN FIXING KIT
KLM
Use spacers for screens with recessed fixings
D1
D2
BT8390-VESA200T / BT8390-VESA400T
Two M6 x 6mm (part D2) screws
are required for a flat 0º display.
10º and 15º quick tilt settings
J
BT8390-VESA400MAF
Installation shown on page 13

4a Hook Screens onto Mounting Rail
Hook screen(s) to mounting rail. Secure mount by tightening safety screw
on bottom of interface arm.
If necessary adjust top levelling screws to align screens.
12
WALL
WALL
SAFETY
SCREW
D4
WALL
LEVELLING
SCREW
D4
WALL
D1
B1
SCREEN
SCREEN
SCREEN
D1
B1

13
DEF
GIH
N
SCREEN FIXING KIT
SCREEN BACK
SCREEN TOP
INTERFACE ARM RIGHT
INTERFACE ARM LEFT
D1
Installing Screens using the BT8390-VESA400MAF
D1
B1
A1
SCREEN
YAXIS
KNOB
YAXIS
KNOB
Z AXIS
KNOB
SECURITY
SCREW
Use the Y & Z micro-adjustment knobs on interface arms to align screens.
When the screens are all positioned correctly, tighten the safety screws
on the bottom of the interface arms (parts D1) to secure in position.
WALL
Hook Screens onto Mounting Rail
4b
3b
Total Z axis
adjustment is 13mm
Total Y axis
adjustment is 20mm
NOTE: Light pressure in
the desired direction of
travel will assist in the
adjustment of knobs when
using heavier screens

14
BT8330
TYPICAL INSTALLATIONS
2 Screen Installation with Fixed VESA 400mm Arms
5 Screen Installation with VESA 200mm Tilt Arms
3 Screen Installation with Fixed VESA 400 Micro-Adjustment Arms
BT8390-VESA400F BT8390-WFK1
BT8390-VESA200T BT8390-WFK1
BT8390-VESA400MAF BT8390-WFK2BT8390-EXT
BT8390-EXT

15
BT8330
POLE MOUNTING INSTALLATIONS
System 2 Single Pole Mounting System 2 Twin Pole Mounting
X-Large Trolley Mounting
BT7850
(x2)
BT7051
(x2) /
BT7841
(x4)
BT8390-CFK
(x2)
BT7850
BT8390-CFK
BT7841 (x2) /
BT7051 (x1)
BT7060 (x2) /
BT4041 (x4) /
BT7260 (x4)
BT4015 (x2)
BT4004
BT8390-CFK
(x2)
For multi-rail ceiling/floor mount suggestions please
refer to the BT8340
BT7850
BT7841 (x2)
BT8390-WFK1
(x2)
System 2 Back-To-Back Installation
BT8390-WFK1 must be used in back-to-back
configurations
BTW100-4
Use with a System 2 floor / ceiling mounts.

B-TECH AUDIO VIDEO MOUNTS
HEAD OFFICE
B-Tech International Limited
Bennett House, Long March, Daventry, Northants., NN11 4NR, UK
Email: [e-mail]
©2015 B-Tech International Limited. All rights reserved.
B-Tech Audio Video Mounts is a division of B-Tech International Limited.
B-Tech, Better By Design & System X are registered trademarks of B-Tech International Limited.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
AMA-BT8330-V1-1015-BTECH
www.btechavmounts.com