Babystart Delfina 377/4467 User manual

Babystart Delfina - Cot Bed
377/4467
377/4474
Assembly Instructions
- Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Important – Please read these instructions fully before starting assembly
Dimensions
Width - 145cm
Depth - 76.5cm
Height - 94cm
Issue 1 - 30/01/13

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
1
. Check you have all the
components and tools listed on
pages 2 and 3.
. Remove all fittings from the
plastic bags and separate them
into their groups.
. Keep children and animals
away from the work area, small
parts could choke if swallowed.
. Make sure you have enough
space to layout the parts before
starting.
. Do not stand or put weight on
the product, this could cause
damage.
. Assemble the item as close
to its final position (in the same
room) as possible.
. Assemble on a soft level
surface to avoid damaging the
unit or your floor.
. We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
. Parts of the assembly will be
easier with 2 people.
. Dispose of all packaging
carefully and responsibly.
This product contain
Natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
.
Care and maintenance
.
. Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
. From time to time check
that there are no loose
screws on this unit.
. This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Note: if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Warning !
· In cot mode, three base height positions are possible. The lowest position is the safest and should
always be used once the child can sit unaided.
· The thickness of the mattress should be such that the distance between the top of the mattress and the
top of the sides should be no less than 500mm with the base in its lowest position and no less than
200mm with the base in its highest position (indicated by printed line on cot frame).
· Do not leave anything (large toys etc.) in the cot which could provide a foothold or present a danger of
suffocation or strangulation.
· The cot is suitable for a mattress of 1400mm in lenght and 700mm in width. For safety reasons, the
minimum mattress size to be used in this cot must be 1380mm in length and 680mm in width.
· Do not position too close to strong sources of heat e.g. open fires, electric fires or gas fires.
· Regularly check the security of fittings and ensure there are no loose screws which could trap parts of
the body, or clothing (e.g. strings, necklaces or ribbons for dummies) which would pose a risk of
strangulation.
· Do not use the cot if any part is broken, torn or missing and use only spare parts approved by the
manufacturer
· Do not use more than one mattress in the cot
· The cot shall no longer be used when the child is able to climb out of the cot to prevent injury from falls
· Designed and manufactured to BS EN 716 -1: 2008
IMPORTANT KEEP IT FOR FUTURE REFERENCE, READ IT CAREFULLY.

Components - Panels
Please check you have all the panels listed below
02
03
04
01
05
06
Headboard x 2-bottom (35 x 76.5cm)
Headboard Panel (64.5 x 25cm)
x 2
Side frame (140 x 69cm) x 2
Headboard x 2-top (59 x 76.5cm)
Side rail x 2 (140 x 9cm)
Slat x 12 (66.4 x 6,7cm)
2

Barrel Nut x 8
2m
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
A
D
B C
3,5 x 25mm Screw
1/4" x 40mm Bolt X 8 Allen key X 1 X 24
3
If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
8,0 x 30mm Wooden dowel X 8
EF
1/4” x 60mm Bolt X 8

Assembly Instructions
Step 2
Step 1
COT
4
D
X 2
DD
Insert 4 wooden dowels
Into headboard-bottom
DD
DD
X 2
02
02
02
01
01
03
03
Fitting dowels
Assembling headboards
Insert headboard panel ,
into headboard top .
Then attach headboard
bottom as shown.

Assembly Instructions
Step 4
Step 3
5
E
E
B
F
F
F
Highest
position
Middle
position
Lowest
position
BE
BE
B
B
E
E
04
B
B
A
45mm
20mm
a) Insert barrel nuts into
side rails as shown.
b) With help fix side rails
to the desired height
position in the assembled
headboards using bolts
and allen key .
B
B
E
E
05
05
05
04
04
Carefully fit side frames
to the headboards as
shown, then fix them
using bolts and allen
key .
AB
AB
AB
AB
AB
AB
AB
A
B
B
E
a)
b)
Attention!
To the correct
position of the side
rails before fixing.
Attention!
Ensure mattress
marks on headboard
are facing inward.
Note: Do not fully
tight bolts.
Finish tighten bolts
on side rails using
allen key .
Attention
Attention
Important:Note there
are three height
positions for the base.
The lowest position is the
safest.Please refer to the
first page, warning section
for more information.
Assembling cot bed

Assembly Instructions
6
Assemble is complete.
Step 5
05
06
C
Fix slats to the side
rails using screws
.
Make sure slats are
fully pushed to the
sides of the side
rails before fixing. And
Fix first slats at 20mm from
the side rails ends, then
work towards to the middle
leaving a space of 50 mm
in between each adjacent
slat, as shown.
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Fix cot base to the
headboard top
using bolts and
allen key .
CC
C
C
C
C
C
C
06
Step 1
JUNIOR BED
01
E
B
BE
B
B
E
BE
BE
01
05
01
B
BE
E
E
Attention to the
correct position of
the side rails before
fixing
Assembling cot base
Assembling junior bed
20mm
45mm
countersunk holes are
facing up.