Balt 90377 User manual

123456789012345678901234567890121234567890123456789012345678901212345678901234

Wallmount Workstation

Assembly Instructions

Part Drawing Description Qty Part Drawing Description Qty

WallmountWorkstation

We recommend that you assemble this

unit on a table.

Do not use unless all screws are tight. At least every six months, check all screws to be sure

they are tight. If parts are missing, broken, damaged, or worn, stop use of the product

until repairs are made by your dealer using factory authorized parts.

P-1 Pole 1 EA

P-2 Bottom Bracket 1 EA

P-3 Top Bracket 1 EA

P-4 Keyboard Back Brkt. 2 EA

P-5 Mouse Holder 1 EA

P-6 Back CPU Holder 1 EA

P-7 Front CPU Holder 1 EA

P-8 Keyboard Platform 1 EA

P-12 CPU Clamp 1 EA

P-9 Bottom Cap 2 EA

P-10 Top Cap 2 EA

P-11 Cable Clip 3 EA

P-13 Arm Cable Clip 4 EA

P-14 KeyboardArm 1 EA

P-15 MonitorArm 1 EA

P-16 Monitor Mount 1 EA

P-17 Monitor Pole Clamp 1 EA

P-18 CPU Knobs 4 EA

P-19 Washer 2 EA

Part Drawing Description Qty

WallmountWorkstation

Do not use unless all screws are tight. At least every six months, check all screws to be sure

they are tight. If parts are missing, broken, damaged, or worn, stop use of the product

until repairs are made by your dealer using factory authorized parts.

Hardware List

Should you require assistance during assembly,

please call our Customer Service Department

Monday - Friday 8 a.m. - 5 p.m.

Central Standard Time 1-800-749-2258

Missing Parts or UPS Damaged Parts

ForYourConvenienceyoucan

EMAILusat

[email protected]

24HOURS 7 DAYSAWEEK

A2 8mm*25 Screw 1 EA

A3 8mm Nut 1 EA

A4 6mm*13 Screw 6 EA

A5 6mm*12 Screw 4 EA

A6 4mm*15 Screw 4 EA

A7 4mm*10 Screw 4 EA

A8 #6*30 Screw 4 EA

A9 #4*10 Screw 4 EA

H1 Allen Wrench Large 1 EA

H2 Allen Wrench Small 1 EA

A1 8mm*55 Screw 1 EA

AssemblyDiagram

Illustration # 1

EAD

HROUGH

NSTRUCTIONS

FROM

BEGINNING

END

BEFORE

STARTING

ASSEMBLE

UNIT

IdentifyandSeparateall the Parts andHardware.

Attachthe Pole (P-1)to the BottomBracket (P-2)

using fourScrews(A5) as showninillustration #1.

TightenScrews(A-1) usingAllenWrench(H-2).

P-1

P-2

Placethethreaded studs on thebottomof the Front CPUHolder(P-7)through the slots inthe

bottomof the Back CPU Holder (P-6) and secure with two CPUKnobs (P-18). AttachtheCPU

Holderassembly to thePole (P-1) usingthe CPU Clamp(P-12) and securingwith two CPU

Knobs(P-18)as shown inillustration#2.

Illustration # 2

1.)

2.)

3.)

P-12

P-18

P-6

P-7

P-18

P-1

4.)

Illustration # 3

5.)

Illustration # 4

P-5

A9 P-8

P-4

TurntheKeyboard Platform(P-8)over and attach the Mouse Holder(P-5)using four Screws (A9)

intothe predrilledholes. Attachthe twoKeyboard BackBrackets (P-4) to the back edge of the

KeyboardPlatform using oneScrew(A4) in eachbracket as showninillustration #3.

Slidethe KeyboardArm (P-14)down Pole (P-1)andtighten the clamplever. Attachthe

KeyboardPlatformassembly from Step4 to theKeyboardArm using four Screws (A4)as

showninillustration#4.

P-1

P-14

Illustration # 5

6.) Loosenthe clamp leveron the MonitorPole Clamp(P-17) and slideit down thePole (P-1).

Tightenthe clamp handletosecure the MonitorPole Clamp to thePole. See illustration #5.

ClampLever

P-1

P-17 ClampLever

7.)

Illustration # 6

P-10

P-15 P-17

P-19

P-9

P-10

Placea BottomCap (P-9)and a Washer (P-19) onthe centerjoint ofthe Monitor Pole

Clamp(P-17) as youslide the MonitorArm(P-15) into placeas shown inillustration #6.

PlaceaWasher (P-19) ontop of theMonitorArmjoint. Insert the longScrew(A1) down

throughtheWasher and inandout of theMonitorArm and MoinitorArmClamp. Secure

thebolt in placeusing Nut(A3) and tighten. Snapin aTop Cap(P-10) on thertop and

bottomof the MonitorArm. Seeillustration#6.

8.)

Follow the Wall Mounting Instructions on Page 7

for the correct wall anchors and screws to use on

your type wall.

AttachtheTop Bracket (P-3)toyourwall at the desireheightyouwant your workstationtohang.

NOTE:

Havea second personhold the assemblyfrom Step 7 upunder theTop Bracket andagainst

thewall. Secure the PoletotheTopBracket using oneScrew(A2) as shownin illustration #7.

TightenScrew(A2) using Allen Wrench(H1). Connect the BottomBracket(P-2), of the

assembly, tothewall using thesamemounting method asyoudid on theTop Bracket.

90377_2-14-13

Illustration # 7

P-2

P-3

P-13

P-11

8a.) Snap on three Caple Clips (P-11) and

twoArm Cable Clips (P-13) as shown

Wall Mounting Instructions

Failure to follow these instructions will void your warranty and

could result in injury.

For Masonry Walls

Usethecorrectwall

predrillforyour

PlasticAnchor

1.) Predrillthe correct diameterpredrill

inthewallwith a masonry drillbit.

2.) Tap in the plastic anchor .

3.) Attachthe unitto the wall withthe .

correctlengthscrew

Screw

Plastic

Anchor

For Wood Stud Walls

2”-3” Lag

Screw

WoodStud

1/8”

Predrill

1.) Predrilla1/8” hole in thethroughthe

wallsurfaceandinto the wood stud.

2.)Attachtheunit to the wallwitha2”-3”

LagScrew.

For Sheetrock Walls

1.)

2.)

3.)

4.)

Drilla 1/2” diameterhole in thesheetrock.

1/2”

Hole

Snaptoggle

Anchor

InserttheSnaptoggleanchor into the 1/2”hole. Holdendsofstraps together and pulltowardyou

untilchannelrestsbehindwall. Ratchetcap along straps until capisflushwithwall.

Pushthumb side toside to snapoffstraps levelwithflange of cap.

Placeunitover flange and insertboltthat came with theSnaptoggleandtighten bolt.

2-15-13

Bolt

Snaptoggle

Anchorinset

position

Wallmount Workstation

90377

90377_2-15-13

26”

8 3/4”

48”

Table of contents

Other Balt Rack & Stand manuals

Balt

Balt Lumina Flat Panel Stand User manual

Balt

Balt PBL User manual

Balt

Balt 27542 User manual

Balt

Balt iTeach 2 User manual

Balt

Balt JPM-1 User manual

Balt

Balt 27534 User manual

Balt

Balt 33550 User manual

Balt

Balt 34429 User manual

Balt

Balt BLT-23701 User manual

Balt

Balt 27624 User manual

Popular Rack & Stand manuals by other brands

MSW

MSW MSW-1800P01 user manual

Handicare

Handicare LinidoSolutions LI2608.000 Series manual

MantelMount

MantelMount MM340 installation instructions

TOOLCRAFT

TOOLCRAFT KCT20CP Assembly instructions

Crestron

Crestron RMK-12L installation guide

iStarUSA

iStarUSA CLAYTEK WOS Series installation guide

Westinghouse

Westinghouse MT80 TILT Installation and assembly

PCB Piezotronics

PCB Piezotronics 080B177 Installation and operating manual

Gymstick

Gymstick STR-MSR Assembly instruction

Enclume

Enclume PR41 quick start guide

Speaka Professional

Speaka Professional SP-TVC-500 Safety instruction

iOptron

iOptron HAE43 quick start guide

Vivo

Vivo VESA MOUNT-AOC1A instruction manual

ELEVATE

ELEVATE 120 Setup guide

Konig & Meyer

Konig & Meyer 18813 quick guide

MAXXTOW

MAXXTOW 70067 instruction manual

StarTech.com

StarTech.com 4POSTRACKBK Assembly instructions

Pulsar

Pulsar ARAS450 installation guide