Balt 27534 User manual

1234567890123456789012345678901212345678901234567890123456789012123456789012

Adjustable Height Sound Powered Lectern

#27534

Assembly Instructions

Part Drawing Description Qty Part Drawing Description Qty

#27534 Parts List

P-14 Microphone Stand 1 EA

P-15 Lamp 1 EA

P-16 Amplifier 1 EA

P-17 Antennae 1 EA

P-18 Cordless Microphone 1 EA

P-19 Battery Charger 1 EA

P-20 Electric Cord 1 EA

PP-21

PP-22

PP-23

Top Cylinder Control 1 EA

1 EA

Cylinder

Cylinder Base

P-11B Top Bottom Shelf 1EA

P-11A Top Middle Shelf 1EA

P-12 Top Insert Block 2 EA

P-13 Book Stop 1EA

P-10 Top Insert -Front 1EA

P-9 Top Insert-Left 1EA

P-8 Top Insert-Right 1EA

P-7 Shelf 1EA

P-6 Front Speaker Cover 1 EA

P-5 Lectern Base 1 EA

P-1 Speaker Panel 1 EA

P-2 Right Side Panel 1 EA

P-3 Left Side Panel 1 EA

P-4 Lectern Top 1EA

Part Drawing Description Qty

Do not use unless all screws are tight. At least every six months, check all screws to be sure

they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until

repairs are made by your dealer using factory authorized parts.

#27534

Velcor

G Velcro Hook 5 EA

H Velcro Loop 5 EA

Hardware List

A Phil Pan Screw M6X25mm 10 EA

A1 Phil Screw M4X12mm 16 EA

A2 Wood Screw M4x58mm 4 EA

A3 CS Wood Screw M4x16mm 3 EA

B Cam Lock 18 EA

B1 Cam Post 1” 8 EA

B2 Cam Post 1-1/4 10 EA

C Wood Dowel 12 EA

D 3” Locking Caster 2 EA

E 3” Inline Caster 2 EA

F Grommet 1 EA

Part Drawing Description Qty

5 EA

Cylinder Base Bolt

Cylinder Base Washer

UppUpper Slide

Upper Slide Screw-Large

Upper Slide Screw-Small

Allen Wrench

8 EA

4 EA

2 EA

4 EA

12 EA

1 EA

QShelf Bracket Screw-Black 8 EA

Shelf Bracket 2 EA

To Assemble:

Identify and Separate all the Parts and Hardware.

Remove Front Cover (P-6) from the Speaker Panel (P-1)

and install 6 Cam Locks (B) in the 6 large holes as shown

in illustrations #1A & 1B.

Illustration # 1A

P-1

#27534 Adjustable Height Sound Powered Lectern

Assembly Diagram

P-6

Be sure that arrow on

top of Camlock (B1)

aligns with centerline

of Edge Drilled hole.

Phillips

Screwdriver

Centerline

of Edge

Drilled hole.

Arrow

Illustration # 2

Install 4 Cam Posts (B2) in the 4 threaded insert nuts in the Right

Side Panel (P-2) as shown in illustration #2.

Install 4 Cam Posts (B2) in the 4 threaded insert nuts in the Left

Side Panel (P-3).

Install 3 each Wood Dowels (C) in the 3 Holes in the Right Side Panel

(P-2) as shown in illustration #2.

Install 3 each Wood Dowels (C) in the 3 Holes in the Left Side Panel

(P-3).

Illustration # 1B P-1

P-2

P-3

Attach Speaker Panel (P-1) to the Right

Side Panel (P-2) as shown in illustration

#4. Secure by turning the Cam Locks

(B) 1/4 Turn until they lock.

Illustration # 3

Illustration # 4 To Secure Cam Locks,

InsertLargePhillips

HeadScrewdriverand

turnCamLock1/4turn

(90 degrees) clockwise.

P-1

P-7

P-2

P-7

7.Install 2 Cam Locks (B) into the 2 large holes in the

Shelf (P-7) as shown in illustration #3.

Should you require assistance

during assembly,

please call our

Customer Service Department

Monday - Friday 8 a.m. - 5 p.m.

Central Standard Time

Toll-Free Customer Service

1-800-749-2258 B

Take the Speaker Wires coming from

Speaker Panel (P-1) and insert them

up and through Shelf (P-7). Place

Shelf (P-7) on Campost (B-2) and

Wood Dowel (C) located on Right

Side Panel (P-2). Turn Camlocks (B)

in the bottom of Shelf (P-7) to lock in

place.

Cam Lock

Detail

B-2

Speaker

Wires to

Amp

Illustration # 6

11. Attach Left Side (P-3) to

the Speaker Panel (P-1)

and Shelf (P-7) as shown

in illustration #5. Secure by

turning the Cam Locks (B)

1/4 Turn until they lock.

P-7

P-3

P-1

P-2

Attach 2 Locking Casters (D) to the front of

Lectern Base (P-5) using 8 Screws (A1) as

shown in illustration #6. Attach 2 Inline

Casters (E) to the back of Lectern Base

(P5) using 8 Screws (A1). D

EA1

P-5

12.

Illustration # 5

13.

Illustration # 7

P-22

P-23

P-5 Install Cylinder Base (P-23) to Lectern

Base (P-5) using four Allen Bolts (J). Use

Allen Wrench (O) to tighten Allen Bolts into

threaded inserts in Lectern Base (P-5). Insert

Cylinder (P-22) into Cylinder Base (P-23).

14.

A-2

Upper Assembly

Base Assembly

Attach the Upper Assembly to the

Base Assembly by lining up the

holes in each and attching with

four Wood Screws (A-2).

Illustration #9

#2# 27534

Place the Top Cylinder Control (P-21)

on top of the Cylinder (P-22) and orient

the handle as shown in Illustration # 9.

15.

PP-21

P-22

Illustration #8

Illustration # 10

Illustration # 11

15.

16B. Attach two Shelf Brackets (P) to Top

Bottom Shelf(P-11B) using four Shelf

Bracket Screws (Q).

Attach Top Insert - Front (P-10), Top

Middle Shelf (P-11A) and Top Bottom

Shelf (P-11B) to the Top Insert-Right

(P-8) and Top Insert-Left (P-9) as

shown in illustration #12. Secure by

turning the Cam Locks (B1) 1/4 Turn

until they lock.

Install 4 Cam Posts (B1) in the 4

threaded insert nuts in the Top

insert - Front (P-10) as shown in

illustration #10.

P-10

P-12

P-9

16A. Attach one Top Insert Block (P-12) to each

Top Insert-Right (P-8) and Top Insert-Left (P-9)

using two Phil Pan Screws (A) as shown in

Illustration # 11.

Illustration # 12

P-11 P-8

P-9

P-10

P-11

#2# 27534

17. Attach the Lectern Top (P-4) to the Upper

Assembly from Step 16B using four Phillips

Pan Screws (A). Line up the mount holes in

(P-4) with the mount holes in the two Top

Insert Blocks (P-12). Insert and tighten

screws (A) as shown in Illustration # 13.

Attach Book Stop (P-13) to Lectern

Top (P-4) using two Phillips Pan Screws (A).

P-4

P-12

18.

P-13

Upper

Assembly

Illustration # 14

Illustration # 13

14”

Peel 2 Velcro Loops (H) off the paper

and attach to the bottom of the

Amplifier (P-16) in the front 2 corners

as shown in illustration #14.

P-16

P-4

Peel 2 Velcro Hooks (G) off

the paper and attach to the

Top Middle Shelf (P-11A)

as shown in illustration #15.

Attach the Shelf Bracket (P)

to the Side Panels using two

Shelf Bracket Screws (Q).

Illustration # 15

19.

P-11

14”

...

Peel 3 Velcro Loops (H) off the paper and

attach to the bottom of the Lamp (P-15) as

shown in illustration #16.

20.

Illustration # 17

21.

22.

P-15

P-4

Insert Grommet (F) in Lectern Top (P-4) as shown in illustration #17.

Route Lamp cord through Grommet (F) in Lectern Top (P-4).

Peel 3 Velcro Hooks (G) off the paper and attach to

the Lectern Top (P-4) as shown in illustration #17.

Attach Lamp (P-15) to Lectern Top

(P-4) as shown in illustration #17.

23.

Illustration # 16

24.

P-15

Illustration # 18

Route Lamp cord through cut-out in Top

insert Front (P-10) as shown

in illustration #18.

25. P-10

Illustration # 18

#2# 27534

26. Attach the Large section of Upper Slide (L) to each side of the Upper LecternAssembly using

three Upper Slide Screws-Small (N) in the predrilled holes as shown in Illustration # 18.

Move the center section of Upper Slide (L) to a point that the third mount hole is exposed

through both sections and then attach the third screw.

Assembly

Upper

27. Attach the Small section of Upper Slide (L)

to each side of the Lower Lectern Assembly

using three Upper Slide Screws-Small (N) and

one Upper Slide Screw-Large (M) in the pre-

drilled holes as shown in Illustration # 19.

Move the center section of Upper Slide (L) to

a point that the third mount hole is exposed

through both sections.

28. Lower the Upper Lectern Assembly down

into the Lower Lectern Assembly until it rests

on the Top Cylinder Control (P-21). Line up

the holes and attach using fourAllen Bolts (J)

and four Flat Washers (K) . Use Allen Wrench

(O) to tighten Allen Bolts into threaded inserts

in the bottom of Top Bottom Shelf (P-11B).

Feed the speaker wires up through the rear

hole in each shelf and to the back of the Amp

(P-16).

Assembly

Lower

Third Screw

Illustration # 19

P-21

P-11B

Speaker

Wires

Third Screw

DC IN 15V

DC OUT 5V FUSE

EX SPEAKER ANT

Illustration # 20

Illustration # 21

Illustration # 23

Remove cap from bottom for

Microphone (amp1) and install

9 volt battery as shown

in illustration #20. Replace cap.

Slide Antennae (P-17) over ANT Mount on

back of Amplifier (P-16) as shown in illustra-

tion #21. Twist collar 90 degrees to lock in

place.

Attach 2 speaker wires to EX SPEAKER

Clips on back of Amplifier (P-16). Attach

positive wire(wire with dash lines) to the EX

SPEAKER Clip marked “+” as shown in

illustration #22.

Attach Negative wire(wire without dash lines)

to the EX SPEAKER Clip marked “-

DC IN 15V is the plug in for the Recharging

Transformer. Amp should be plugged in and

charged for 4 hours before 1st use.

DC OUT 5V is the Outlet for the lamp. Plug

Lamp ( P15) into this outlet.

29.

30.

31.

33.

31.

34.

P-18

P-16

P-17

Insert Electric Cord (P-20) in the end

of Battery Charger (P-19) as shown in

illustration #19.

Illustration # 22

P-20

P-19

32.

#2# 27534

Place Charger & Electric Cord

(P-19 & P-20) onto Top Middle Shelf

(P-11A) as shown in illustration # 24.

Place amplifier (P-16) onto 1st Shelf

(P-7) as shown in illustration # 24.

Align Velcro Hooks and Loops (G & H)

and Press.

35.Attach Microphone Stand (P-14) to

the Lectern Top (P-4) using 3 each

screws (A3) as shown

in illustration #23.

Press both sides of clamp on

Microphone Stand (P-14) and

insert Wireless Microphone (P18).

Illustration # 24

Illustration # 26

36.

37.

27534 - 07/07/09

39.Attach Front Speaker Cover (P-6) to

the Speaker Panel (P-1) by inserting

the Metal Pins into the 4 Holes as

shown in illustration #25.

P-6

P-1

38.

P-14

P-4

P-18

P-19

P-20

P-11

P-16

Illustration # 25

#2# 27534

27534_11-11-09

Table of contents

Other Balt Rack & Stand manuals

Balt

Balt iTeach 2 User manual

Balt

Balt 34429 User manual

Balt

Balt PBL User manual

Balt

Balt 27542 User manual

Balt

Balt 90377 User manual

Balt

Balt JPM-1 User manual

Balt

Balt 33550 User manual

Balt

Balt Lumina Flat Panel Stand User manual

Balt

Balt BLT-23701 User manual

Balt

Balt 27624 User manual

Popular Rack & Stand manuals by other brands

Store More

Store More Sloped Shelf Shelving Assembly guide

roomours

roomours Front Row installation instructions

Mountup

Mountup MU5001 instruction manual

Noctua

Noctua NF-A12x15 FLX user manual

Zeiss

Zeiss Floor Stand S operating manual

Sanus

Sanus WMS3 manual

Unicol

Unicol AXIA TITAN Assembly instructions

Cornwell Tools

Cornwell Tools CTJ1000PPJ operating instructions

NETGEAR

NETGEAR Orbi RBKWMB quick start guide

Sunny

Sunny SYS1621-W Series User manual and safety information

Tektronix

Tektronix RM2000 instructions

Konig & Meyer

Konig & Meyer Ring Lock 21360 quick start guide

Chauvet Professional

Chauvet Professional CPRACK Quick reference guide

Covini

Covini Xi Presenter Assembly instruction

Axis

Axis T94A01C installation guide

Bauhn

Bauhn ALPB80-0420 installation guide

BDS

BDS 106-223 Service manual

Edbak

Edbak TR24 installation manual