Barco R9001290 User manual

R9001290
OWNER'S MANUAL
VISION
9200

BARCO PROJECTION SYSTEMS
Date :
280497 Art. No. : R5975338
R9001290
OWNER'S MANUAL
VISION
9200
Rev :
01

Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, April 1997.
All rights reserved.
Trademarks are the rights of their respective owners.
Printed in Belgium
BARCO nv/Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Printed in Belgium

Table of Contents
i-1
5975338 BARCOVISION 9200 280497
TABLE OF CONTENTS
i
TABLE OF CONTENTS ................................................................................................................................................................... i-1
SAFETY INSTRUCTIONS...............................................................................................................................................................1-1
REMARQUE SUR LA SÉCURITÉ ...................................................................................................................................................1-2
UNPACKING AND DIMENSIONS ...................................................................................................................................................2-1
Unpacking .............................................................................................................................................................................2-1
Projector dimensions .............................................................................................................................................................2-1
Battery installation in the RCU. ..............................................................................................................................................2-2
INSTALLATION GUIDELINES ........................................................................................................................................................ 3-1
Environment ..........................................................................................................................................................................3-1
What about ambient light ? ....................................................................................................................................................3-1
Which screen type? ............................................................................................................................................................... 3-1
What image size? How big should the image be? ................................................................................................................. 3-1
Where to install the projector? ...............................................................................................................................................3-2
How to install a projection lens? ............................................................................................................................................ 3-3
How to install the projector?................................................................................................................................................... 3-3
LOCATION AND FUCNTIONS OF CONTROL ................................................................................................................................4-1
Front panel terminology.........................................................................................................................................................4-1
Control panel terminology .....................................................................................................................................................4-1
INSTALLATION SET UP .................................................................................................................................................................5-1
CONNECTIONS .............................................................................................................................................................................6-1
Power (mains) cord connection .............................................................................................................................................6-1
Fuses ....................................................................................................................................................................................6-1
Switching on..........................................................................................................................................................................6-1
Switching to stand-by. ...........................................................................................................................................................6-2
Switching off..........................................................................................................................................................................6-2
Input connections. .................................................................................................................................................................6-2
Input module insertion into the projector : .............................................................................................................................. 6-2
Video/S-video input module ................................................................................................................................................... 6-3
RGB analog input module...................................................................................................................................................... 6-4
Component input module....................................................................................................................................................... 6-5
RGB3S/RG3sB input module................................................................................................................................................. 6-6
Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector..........................6-7
Set up of the baud rate for communication with a computer. ................................................................................................. 6-7
Connecting a RCVDS 05 to the projector. ..............................................................................................................................6-8
Connecting a VS05 to the projector ....................................................................................................................................... 6-8
Connecting an IR Remote Receiver 800 to the projector........................................................................................................6-8
CONTROLLING .............................................................................................................................................................................. 7-1
How to use the RCU? ............................................................................................................................................................7-1
Projector address .................................................................................................................................................................. 7-1
How to display a projector address? ...................................................................................................................................... 7-2
How to program an address into the RCU? ............................................................................................................................ 7-2
Picture controls with direct access. ........................................................................................................................................ 7-2
How to get source information ...............................................................................................................................................7-3
How to get a summary of your projector ................................................................................................................................7-4
SOURCE SET UP ...........................................................................................................................................................................8-1
Input selection .......................................................................................................................................................................8-1
Installation of the settings for a input source ..........................................................................................................................8-1
Edit file .................................................................................................................................................................................. 8-2
Rename ................................................................................................................................................................................ 8-4
Copy .....................................................................................................................................................................................8-4
Move .....................................................................................................................................................................................8-5
Delete ...................................................................................................................................................................................8-5
Options .................................................................................................................................................................................8-5
PICTURE CONTROL IN ADJUSTMENT MODE .............................................................................................................................. 9-1
Signal operations................................................................................................................................................................... 9-1
Video offset ........................................................................................................................................................................... 9-1
Gain ......................................................................................................................................................................................9-1

Table of Contents
i-2 5975338 BARCOVISION 9200 280497
Gain adjustment per color ..................................................................................................................................................... 9-2
Smoothness .......................................................................................................................................................................... 9-2
Still Video.............................................................................................................................................................................. 9-2
Sync ..................................................................................................................................................................................... 9-2
Color balance ........................................................................................................................................................................ 9-2
Screen operations ................................................................................................................................................................. 9-3
Zoom/pan.............................................................................................................................................................................. 9-3
Configure .............................................................................................................................................................................. 9-7
Conversion............................................................................................................................................................................ 9-7
Geometry .............................................................................................................................................................................. 9-7
SERVICE MODE .......................................................................................................................................................................... 10-1
How to activate the password function ................................................................................................................................ 10-1
Start up the Service mode ................................................................................................................................................... 10-1
Convergence adjustment of the LCD panels........................................................................................................................ 10-2
Modify password ................................................................................................................................................................. 10-5
Lamp run time history.......................................................................................................................................................... 10-5
Reset lamp run time ............................................................................................................................................................ 10-5
Appendix A : Standard Source Set Up Files .................................................................................................................................... A-1
Appendix B : Battery replacement in the RCU .................................................................................................................................B-1
Appendix C : Lenses .......................................................................................................................................................................B-1
Focusing the lens ..................................................................................................................................................................B-1
Lens Cleaning Procedure ......................................................................................................................................................B-1
Lenses ..................................................................................................................................................................................B-2
Appendix D : Source numbers 90 - 99.............................................................................................................................................C-1

Safety Instructions
1-1
5975338 BARCOVISION 9200 210497
1SAFETY INSTRUCTIONS
Projectors are built in accordance with the requirements of the
international safety standards IEC950, UL 1950 and CSA C22.2 No.
950,which arethesafety standardsofinformation technologyequip-
ment including electrical business equipment.
Thesesafetystandardsimposeimportantrequirementsontheuseof
safetycriticalcomponents,materialsandisolation,inordertoprotect
the user or operator against the risk of electric shock and energy
hazard, and having access to live parts.
Safetystandardsalsoimposetotheinternalandexternaltemperature
rises, radiation levels, mechanical stability and strength, enclosure
construction and protection against risk of fire.
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal operation
fails.
Installation instructions
Before operating your projector please read this manual thoroughly,
and retain it for future reference.
Installation and preliminary adjustments should be performed by
qualified BARCO personnel or authorized BARCO service dealers.
OWNER’S RECORD
The part number and serial number are located at the front of the
projector.Recordthesenumbersinthespacesprovidedbelow.Refer
to them whenever you call upon your BARCO dealer regarding this
product.
PART NUMBER:
SER. NUMBER:
DEALER:
The lightning flash with an arrowhead within a
triangle is intended to tell the user that parts
inside this product are risk of electrical shock
to persons.
The exclamation point within a triangle is
intendedto tellthe userthat important operat-
ing and/or servicing instructions are included
in the technical documentation for this equip-
ment.
Warning
To prevent fire or electrical shock hazard, do not expose this
projector to rain or moisture
Federal communication commission (FCC statement)
This equipment has been tested and found to comply with the limits
for a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmfulinterferencewhentheequipmentisoperatedinacommercial
environment. Thisequipmentgenerates,uses,andcanradiateradio
frequencyenergyand,ifnotinstalledandusedinaccordancewiththe
instruction manual, may cause harmful interference to radio commu-
nications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Instructions to the user :
if this equipment does cause interference to radio or television
reception,the user maytryto correcttheinterference byoneor more
of the following measures :
- Re-orientation of the receiving antenna for the radio or television.
- Relocate the equipment with respect to the receiver.
- Plug the equipment into a different outlet so that the equipment and
receiver are on different branch circuits.
• Fasten cables connectors to the equipment by mounting screws.
Note :
The use of shielded cables is required to comply within the limits of
Part15 of FCC rules and EN55022.
General safety instructions.
*Allthesafetyandoperatinginstructionsshouldbereadbeforeusing
this unit.
* The operating instructions manual should be retained for future
reference.
* All warnings on the projector and in the documentation manuals
should be adhered to.
* All instructions for operating and use of this equipment must be
followed precisely.
ON SAFETY
* This product should be operated from an AC power source. This
projector may be connected to an IT-power system.
*Thisproductisequippedwitha3-wiregroundingplug,aplughaving
a third (grounding) pin. This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the purpose of the grounding-type
plug.
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE
GROUNDED (EARTHED) via the supplied 3 conductor AC power
cable.
(If the supplied power cable is not the correct one, consult your
dealer.)
Mains lead (AC Power cord) with CEE 7 plug:
The colors of the mains lead are colored in
accordance with the following code:
Green-and-yellow: Earth (safety earth)
Blue: Neutral
Brown: Line

Safety Instructions
1-2 5975338 BARCOVISION 9200 210497
Remarque sur la Sécurité
Les projecteurs sont fabriqués conformément aux exigences des
normes de sécurité internationales IEC950, UL 1950 et CSA C22.2
No.950.Cesnormesdesécuritésontimposéesauxéquipements de
la technologie informatique incluant les équipements électriques.
Ces normes de sécurité imposent des exigences importantes sur
l’emploi des composantes, des matériaux et de l’isolation dont la
sécuritéestcritique,afindeprotégerl’utilisateurcontrelerisqued’une
décharge électrique et d’avoir accès aux parties sous tension.
Lesnormes desécurité aussiimposent deslimitations concernantla
haussedelatempératureinterneetexterne,lesniveauxderadiation,
lastabilité etla forcemécanique, laconstruction ducadre métallique
à l’intérieure et la protection contre les risques d’incendie.
Lesépreuvesauxquellesl’équipementaétésubiassurentlasécurité
totale de l’utilisateur, même lorsque l’équipement ne fonctionne pas
normalement.
Instructions pour l’installation
Lire ce manuel complètement avant de mettre l’appareil en fonction-
nement et le conserver pour consultation ultérieure.
L’installation et les réglages préliminaires devraient être faits par du
personnel qualifié BARCO ou par des agents autorisés du service
BARCO.
DONNEES POUR LE PROPRIETAIRE
Le numéro de pièce et le numéro de série sont situés à l’arrière du
projecteur.Copiercesnumérosdanslesespacesprévusci-dessous.
Seréféreràcesnuméroschaquefoisquevousconsultezvotreagent
BARCO concernant cet appareil.
NUMERO DE PIECE :
NUMERO DE SERIE :
AGENT :
AVERTISSEMENT
POUR EVITER DES RISQUES D’INCENDIE OU DE CHOCS
ELECTRIQUES, NE PAS EXPOSER CE PROJECTEUR A LA
PLUIE OU A L’HUMIDITE
Fédéral communication commission (FCC statement)
Cet équipement a été testé et trouvé conforme aux limites imposées
aux appareils digitaux de classe A, selon la section 15 des règles
FCC. Ces limites sont conçues pour fournir une protection raisonna-
ble contre les interférences lorsque l’utilisation doit se faire dans un
environnement commercial. Cet équipement génère, utilise et peut
émettre de l’énergie aux fréquences radio, et s’il n’est pas installé
etutilisé conformément auxinstructionsdu manuel,il peutcréer des
interférences désavantageuses dans les communications radio.
L’utilisation de cet équipement dans des zones résidentielles peut
créer des interférences. Le cas échéant, l’utilisateur devra prendre
toutes les mesures requises pour les amoindrir, à ses propres frais.
Instructions pour l’utilisateur :
Sicetéquipementcausedes interférences de radiooude télévision,
l’utilisateur peut essayer de corriger les interférences en appliquant
une ou plusieurs de les mesures suivantes :
- Ré-orienter l’antenne radio ou télévision.
- Déplacer l’ équipement concernant le récepteur.
- Brancher l’ appareil sur une autre prise de telle sorte que l’appareil
et le récepteur se trouvent sur différents circuits électriques.
. Fixer les connecteurs des cables a l’équipement au moyen des vis.
Remarque :
L’utilisation de câbles blindés est exigée afin d’observer les règles
de la section 15 des règles FCC et EN55022.
Prescriptions de securite générales.
*Lire toutes lesprescriptionsde sécuritéetdefonctionnement avant
d’utiliser cet appareil.
* Le manuel de prescriptions de securite et de fonctionnement doit
être conservé pour consultation ultérieure.
*Ilfautrespectertouslesavertissementsmentionnéssurleprojecteur
et dans les manuels.
* Suivre fidèlement toutes les prescriptions d’utilisation et de
fonctionnement de cet équipement.
SECURITE
*Cetéquipementdoitfonctionnersurunesourceàcourantalternatif.
Ce projecteur peut être branché sur un système à IT courant.
* Cet appareil est équipé d’un connecteur à trois broches dont une
mise à la terre. Le connecteur n’est adapté qu’à des prises de
courant du type avec terre. Ceci est une mesure de sécurité. Si le
connecteurnes’adaptepasdanslaprise,contactervotreélectricien
pourremplacerlaprise nonvalable.Nepascompromettrele but du
connecteur de terre.
Avertissement pour les utilisateurs : CE PROJECTEUR DOIT ÊTRE
MIS À LA TERRE avec le cordon secteur fourni.
(Si le cordon secteur n'est pas correct, consulter votre revendeur.)
Cordon d’alimentation avec connecteur
CEE7
Les couleurs des fils du cordon d’alimentation
sont codées comme suit :
Vert et jaune : terre
Bleu : neutre
Brun : sous tension (actif)
RISQUE D'ELECTRO-
CUTION NE PAS OUVRIR
ATTENTION
ATTENTION : AFIN DE REDUIRE LE RISQUE DE CHOCS
ELECTRIQUES, NE PAS ENLEVER LE COUVERCLE (OU LE DOS)
IL N'Y A PAS DE PIECES REPARABLES PAR L'UTILISATEUR A
L'INTERIEUR
LESERVICENE PEUTETREEFFECTUEQUEPARDUPERSONNEL
QUALIFIÉ
L’éclair avec une tête de flèche dans un triangle
indiqueà l’utilisateurque lespièces àl’intérieur de
l’appareil présentent un risque de chocs électri-
ques.
Le point d’exclamation dans un triangle indique à
l’utilisateur que des instructions de fonctionne-
ment et/ou de service sont comprises dans la
documentation technique de cet équipement.

Safety Instructions
1-3
5975338 BARCOVISION 9200 210497
* Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
* To disconnect the cord, pull it out by the plug. Never pull the cord
itself.
*Ifanextensioncordisusedwiththisproduct,makesurethatthetotal
of the ampere ratings on the products plugged into the extension
corddoes not exceedthe extension cordampere rating. Alsomake
sure that the total of all products plugged into the wall outlet does
not exceed 15 amperes.
*Neverpushobjectsofanykindintothisproductthroughcabinetslots
as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
*Neverspillliquidofanykindontheproduct.Shouldanyliquidorsolid
object fall into the cabinet, unplug the set and have it checked by
qualified service personnel before resuming operations.
* Lightning - For added protection for this video product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent
damageto theprojector dueto lightning andAC power-linesurges.
* To reduce the lamp heat of the projector, switch the projector first
to stand-by and let the projector lamp cool down for at least 15
minutes. Then the projector may be switched off with the power
switch.
On Installation
* Do not place this projector on an unstable cart, stand, or table. The
projector may fall, causing serious damage to it.
* Do not use this projector near water.
* Use only the power cord supplied with your projector. While
appearing to be similar, other power cords have not been safety
testedatthefactoryandmaynotbeusedtopowertheprojector. For
a replacement power cord, contact your dealer.
* Slots and openings in the cabinet and the sides are provided for
ventilation; to ensure reliable operation of the projector and to
protect it from overheating, these openings must not be blocked or
covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This prod-
uct should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation or
enclosure unless proper ventilation is provided.
* Do not block the projector cooling fans or free air movement under
andaroundtheprojector.Loosepapersorother objects may notbe
nearer to the projector than 4" on any side.
On Servicing
Do not attempt to service this projector yourself, as opening or
removingcoversmayexposeyoutodangerousvoltagepotentialand
riskofelectricshock! ReferallprojectorservicetoaqualifiedBARCO
service center.
Call for service in the following conditions :
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the projector.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating
instructions are followed.
Adjust only those controls that are covered by the operating in-
structions since improper adjustment of the other controls may
resultindamageandwilloftenrequireextensiveworkbyaqualified
technician to restore the product to normal operation;
- If the product has been dropped or the cabinet has been damaged;
- If the product exhibits a distinct change in performance, indicating
a need for service.
Replacement parts - When replacement parts are required, be sure
theservicetechnicianhasusedoriginalBARCOreplacementpartsor
authorizedreplacementpartswhichhavethesamecharacteristicsas
the BARCO original part. Unauthorized substitutions may result in
degraded performance and reliability, fire, electric shock or other
hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this
projector, ask the service technician to perform safety checks to
determine that the projector is in proper operating condition.
Theprojectorusesa1500 W metalhalideprojectionlamp.Replacing
the projection lamp with any other projection lamp can cause over-
heatingorunacceptableimagequality.Useonlytheprojectionlamps
specified by BARCO, or an authorized BARCO dealer or service
center.
On Cleaning
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Tokeepthecabinetlookingbrand-new,periodicallycleanitwithasoft
cloth.Stubbornstains mayberemovedwith a clothlightlydampened
with mild detergent solution. Never use strong solvents, such as
thinneror benzine, orabrasivecleaners, sincethesewill damagethe
cabinet.
Toensurethehighestopticalperformanceandresolution,theprojec-
tion lenses are specially treated with an anti-reflective coating,
therefore : avoid touching the lens. To remove dust on the lens, use
asoftdrycloth.Donotuseadampcloth,detergentsolution,orthinner.
Follow the lens cleaning procedure on Appendix B in the Owners
Manual.
On Repacking
Savetheoriginalshippingcartonandpackingmaterial;theywillcome
in handy if you ever have to ship your projector. For maximum
protection, repack your set as it was originally packed at the factory.
On illumination
Inordertoobtainthebestqualityfortheprojectedimage,itisessential
that the ambient light which is allowed to fall on the screen be kept to
an absolute minimum.
Wheninstallingtheprojectorandscreen,care mustbetakentoavoid
exposure to ambient light directly on the screen. Avoid adverse
illumination on the screen from direct sunlight or fluorescent lighting
fixtures.
The use of controlled ambient lighting, such as incandescent spot
light or a dimmer, is recommended for proper room illumination.
Where possible, care should also be taken to ensure that the floors
andwalls oftheroom inwhichthe projectoristo beinstalledare non-
reflecting, dark surfaces. Brighter surfaces will tend to reflect and
diffuse the ambient light and hence reduce the contrast of the
projected image on the screen.

Safety Instructions
1-4 5975338 BARCOVISION 9200 210497
* Ne rien laisser en appui sur le cordon d’alimentation. Ne pas placer
ce cordon là où des personnes risques de marcher dessus.
* Pour débrancher le cordon, le tirer par le connecteur, jamais par le
cordon lui-même.
* Si on utilise une rallonge, vérifier que le total des courants des
appareils raccordés à cette rallonge ne dépasse pas la capacité
nominale du câble de rallonge. Vérifier aussi que la somme des
consommations des appareils raccordés à la prise murale ne
dépasse pas 15 ampères.
* Ne jamais introduire un objet quelconque dans l’appareil à travers
les fentes du boîtier, car ils pourraient être en contact avec des
points de tension dangereux ou court-circuiter des pièces, ce qui
pourrait entraîner un risque d’incendie ou de choc électrique.
* Ne jamais répandre un liquide quelconque sur l’appareil. Si un
liquide ou un objet solide tombe dans le boîtier, débrancher l’appa-
reil et le faire vérifier par du personnel qualifié avant de reprendre
l’utilisation.
* Foudre - Pour une protection supplémentaire de cet appareil vidéo
lorsd’un orageou s’il n’estpas employéet laissésanssurveillance
pendantdelonguespériodes,ledébrancherdelaprisemurale.Ceci
évite tout endommagement au projecteur par la foudre ou par des
impulsions sur le secteur.
*Avantdedébrancherleprojecteur,réduirelachaleurdelalampeen
commutant le projecteur en mode d’attente et laisser refroidir la
lampe du projecteur pendant 15 minutes au moins. Puis le projec-
teur peut être débranché par l’interrupteur secteur.
L’Installation
* Ne pas placer le projecteur sur un chariot, un support ou une table
instable. Le projecteur risquerait de tomber causant des dégâts
sérieux au projecteur.
* Ne pas utiliser le projecteur à proximité d’eau.
* N’utiliser que le cordon d’alimentation fourni avec votre projecteur.
Bien qu’ils se ressemblent, d’autres cordons d’alimentation n’ont
passubidestestsdesécuritédansl’usineetpourcetteraisonilsne
peuvent pas être utilisés pour actionner le projecteur. Si vous avez
besoin d’un cordon d’alimentation de remplacement, contactez
votre agent.
* Les fentes et les ouvertures pourvues dans le boîtier et au dos ou
surlefond,sontdestinéesàlaventilation.Pourassurerunfonction-
nement fiable du projecteur et le protéger de toute surchauffe, ses
ouvertures ne doivent être ni obstruées ni recouvertes. Les
ouverturesne devraientjamais être obstruéesen plaçantl’appareil
sur un lit, un divan, un tapis ou toute autre surface similaire.
L’appareil ne devrait jamais être placé près ou au-dessus d’un
radiateurouautresource dechaleur.Ceprojecteurnedoit pas être
installé dans une installation encastrée ou fermée, sauf si une
ventilation suffisante est assurée.
* Laisser suffisamment d’espace autour du projecteur et ne pas
obstruer la circulation de l’air. Ne pas mettre des feuilles libres ou
d’autres objets plus près de 11 cm du projecteur.
Entretien et Réparation
Ne pas essayer de réparer le projecteur vous-même, puisque ouvrir
leboîtieroul’enlèvementdesblindages peuvent vousexposeràune
puissance électrique dangereuse et au risque d’une décharge
électrique.
Contacter le service technique qualifié dans les cas suivants :
- Si le cordon secteur ou la prise de courant est endommagé ou
effiloché.
- Si on a répandu du liquide dans le projecteur.
- Si l’appareil a été exposé à la pluie ou à de l’eau.
- Si l’ appareil ne fonctionne pas normalement, bien que les instruc-
tions soient correctement suivies. Ne régler que les commandes
décrites dans les instructions de fonctionnement, car un mauvais
réglage d’autres commandes peut entraîner des dégâts et souvent
nécessiter un travail important par un technicien qualifié pour
remettre l’appareil en conditions de fonctionnement normal.
- Si l’appareil est tombé ou si le boîtier est endommagé.
- Si l’appareil présente des changements nets de performance,
indiquant un besoin de réparation.
Pièces de rechange - Lorsqu’on a besoin des pièces de rechange,
veiller à ce que le technicien de service utilise des pièces d’origine
BARCO ou des pièces équivalentes autorisées qui ont les mêmes
caractéristiquesquelapièced’origineBARCO.Unremplacementpar
des pièces de rechange non autorisées peut nuire à la performance
et la fiabilité, entraîner incendies, chocs électriques ou d’autres
dangers. L’utilisation de pièces de rechange non autorisées peut
annuler la garantie.
Vérification de sécurité - Lorsqu’un service ou une réparation sur
ceprojecteurestterminé,demanderautechniciendeservicedefaire
les vérifications de sécurité pour s’assurer que le projecteur est en
bon état de fonctionnement.
Leprojecteur emploieune lampehalogène à vapeursmétalliques de
1500W.Remplacerlalampeparunelampedeprojectionquelconque
peut causer la surchauffe ou une qualité de l’image inacceptable.
N’utiliser que des lampes de projection indiquées par BARCO ou un
agent autorisé de BARCO ou un service.
Nettoyage
Débrancherl’appareildelapriseavanttoutnettoyage.Nepasutiliser
des détergents liquides ou des aérosols. Utiliser un chiffon humide
pour le nettoyage.
Pourgarderauboîtiersonaspectneuf,lenettoyerrégulièrementavec
un chiffon doux. Des tâches tenaces peuvent être enlevées avec un
chiffon humidifié par une solution de détergent doux. Ne jamais
utiliser des solvants forts, tels que du ‘thinner’ ou du benzène, ni des
produits de nettoyage abrasifs, car ils pourraient endommager le
boîtier.
Pourgarantirlesmeilleuresperformanceetdéfinition,lesobjectifsde
projection sont spécialement traités avec un revêtement anti-reflets.
En conséquence : éviter de toucher les objectifs. Pour enlever la
poussière de l’objectif, utiliser un chiffon sec et doux. Ne pas utiliser
dechiffonhumide,desolutiondétergente ou de diluant.Respecterla
méthode de nettoyage des objectifs indiquée dans l’annexe B au
manuel d'utilisateur.
Ré-emballage
Conserverl’emballageetlesproduitsd’emballaged’origine,ilsseront
d’un précieux secours s’il avère utile d’expédier le projecteur. Pour
une protection maximale, ré-emballer l’appareil de la même manière
qu’à l’usine.
Eclairage
Pour garantir la meilleure qualité possible de l’image projetée, il est
essentiel que l’éclairage ambiant incident sur l’écran soit réduit au
strict minimum.
Lors de l’installation du projecteur et de l’écran, il faut veiller à éviter
toute exposition directe de l’écran à la lumière ambiante. Eviter tout
éclairage perturbateur sur l’écran par des rayons du soleil ou des
éclairages fluorescents.
L’utilisation d’un éclairage ambiant contrôlable, tel qu’un spot incan-
descentouunvariateurdelumièreestrecommandéepourobtenirun
éclairagecorrect dela pièce.Dans lamesure du possibleveiller àce
quelesparoisetlesol delapiècedanslaquelleleprojecteurdoitêtre
installésoient non-réfléchissants etde couleur foncée.Des surfaces
brillantes réfléchissent et diffusent la lumière ambiante et par consé-
quent réduisent le contraste de l’image sur l’écran.

Unpacking and Dimensions
2-1
5975338 BARCOVISION 9200 210497
27.1
1125.7
630
422.18
70
208.6
150702.342 50.3
135.2
284.25
568.5
468.2
Center of gravity
2UNPACKINGAND DIMENSIONS
Unpacking
To open the banding, pull on the clip as shown in the first drawing.
Take the projector out of its shipping carton and place it on a table.
For transportation, the projector is mounted on a wooden board with 3 bolts. Use a 13 mm wrench to remove these bolts.
Whenusing theprojector as atable mountedconfiguration, alwaysmountthe 3supporting feet(see drawing below). Thesefeet aremounted
on the same wooden board. Each food contains one metal part and two plastic parts. To remove the feed, first turn out both plastic parts.
To remove the metal parts from the board, remove the retaining bolts. Save these bolts because these bolts must be used to mount the feet
to the projector. Mount first the metal parts with the removed bolts and turn in then both plastic parts to finish the feed.
Warning : To prevent overheating of the projector as table mounted, always remove the wooden board and turn in the 3 supporting feet to
1 234 5
379
allow air circulation via the built-in dust filter at the bottom.
Save the original shipping carton and packing material, they will
come in handy if you ever have to ship your projector. For maximum
protection, repack your projector as it was originally packed at the
factory.
Contents of the shipped box :
- 1 BARCOVISION 9200 (weight ± 88 kg)
- 1 remote control unit RCU + 9V battery
- 1 power cable with outlet plug type CEE7.
- 1 owner’s manual
- 3 supporting feet (built up in 3 parts)
Projector dimensions
(units : mm)
Name lens
(*)
HD(1.2:1)
HD(2.2:1)
HD(3.3:1)
HD(4.0:1)
HD(5:1)
HD(7:1)
HD(1.5-3:1)
HD(3-5.3:1)
Some examples of lenses :
(*) More info about lenses, see
appendix B.
Pull
To open

Unpacking and Dimensions
2-2 5975338 BARCOVISION 9200 210497
Battery installation in the RCU.
A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power
cord. To install the battery, remove the battery cover on the backside of the remote control by pushing
the indicated handle a little to the bottom of the RCU. Lift up the top side of the cover at the same time
(fig. 1).
Insertthe new 9Vbattery (typeE-blockor equivalent)inthe lower compartmentandconnect thebattery
to the contact plate.
Insert the battery into the lower compartment and put the cover back.
Note : projector address has to be programmed on the RCU before using the RCU (see chapter
'Controlling').
fig.1
310a.DRW
fig.2
Insert here the 'Insert card
RCU' which you can cut out
on the last page of this
manual.
Contact
plate
Battery

Installation Guidelines
3-1
5975338 BARCOVISION 9200 210497
3INSTALLATIONGUIDELINES
Installation guidelines
Careful consideration of things as image size, ambient light level,
projector placement and type of screen to use are critical to the
optimum use of the projection system.
Max. ambient temperature : 40 °C.
* Environment
Do not install the projection system in a site near heat sources such
as radiators or air ducts, or in a place subject to direct sunlight,
excessive dust or humidity. Be aware that room heat rises to the
ceiling; check that temperature near the installation site is not
excessive.
* What about ambient light ?
The ambient light level of any room is made up of direct or indirect
sunlightandthelightfixturesintheroom. Theamountofambientlight
willdetermine howbrightthe imagewill appear. So, avoiddirect light
on the screen.
Windows that face the screen should be covered by opaque drapery
while the set is being viewed. It is desirable to install the projecting
systeminaroomwhosewallsandfloorareofnon-reflectingmaterial.
The use of recessed ceiling lights and a method of dimming those
lights to an acceptable level is also important. Too much ambient
light results in a ‘wash out’ of the projected image. That appears as
less contrast between the darkest and lightest parts of the image.
With bigger screens, the ‘wash out’ becomes more important. As a
generalrule,darkentheroomtothepointwherethereisjustsufficient
light to read or write comfortably. Spot lighting is desirable for
illuminating small areas so that interference with the screen is
minimal.
* Which screen type?
There are two major categories of screens used for projection
equipment. Thoseusedfor frontprojectedimagesand thoseforrear
projection applications.
Screens are rated by how much light they reflect (or transmit in the
case of rear projection systems) given a determined amount of light
projected toward them. The ‘GAIN’ of a screen is the term used.
Front and rear screens are both rated in terms of gain. The gain of
screens range from a white matte screen with a gain of 1 (x1) to a
brushed aluminized screen with a gain of 10 (x10) or more. The
choice between higher and lower gain screens is largely a matter of
personal preference and another consideration called the Viewing
angle.
In considering the type of screen to choose, determine where the
viewers will be located and go for the highest gain screen possible.
A high gain screen will provide a brighter picture but reduce the
viewing angle.
For more information about screens, contact your local screen
supplier.
* What image size? How big should the image be?
The projector is designed for projecting an image size (video) from
1.00m (3.3ft) to 15.00m (49.2ft) with a aspect ratio of 4 to 3.
Screen width

Installation Guidelines
3-2 5975338 BARCOVISION 9200 210497
* Where to install the projector?
Definitions of the Abbreviation on drawings
B = Distance between ceiling and top of the screen or
between floor and bottom of the screen.
A=Correctionvalue,distancebetweenbottomsideofprojec-
tor (without feed) and middle of the lens. Value to be sub-
tracted from B to obtain the correct installation position. (A
value is a constant value for all screen widths and type of
lenses, A = 278.56 mm.)
CD=Totaldistancebetweenprojectorandceilingorprojector
and floor.
SW = Screen width.
SH = Screen height (image height).
PD = Projector Distance, distance between screen and pro-
jector.
Lenstype selection.
a) determine the required screen width.
b) determine the approximate position of the projector in the projec-
tion room with regard to the screen and measure the
projector-screen distance (PD).
c)use thelens formulasin appendixB tofind thebest corresponding
PD with regard to the measured projector-screen distance for the
required screen width.
Thedesiredlensisdetermined(theordernumberisgiveninthetabel
in the same appendix B).
Start the installation procedure for the projector as described in
the manual.
Inputs and computer video format input compatibility :
Some examples :
VIDEO and S-VIDEO
COMPONENT VIDEO
RGB ANALOG with STANDARD SYNC (SYNC ON GREEN or
SEPARATE SYNC)
RGB ANALOG with TRI-LEVEL SYNC (SYNC ON GREEN or
SEPARATE SYNC)
VGA : 640 x 480 pixels
MAC : 640 x 480 pixels
Super VGA : 800 x 600 pixels (only in a window of 756 x 556 pixels)
Screen
PD
B
Ceiling
Projector
CD
A
CD = B - A
SH
Optical axis projection lens
SH
SW
SIDE VIEW
BACK VIEW
Screen
BOTTOM VIEW
SW
Ceiling
Screen
PD
B
Floor
Projector
CD
A
CD = B - A
SH
Optical axis projection lens
SH
SW
SIDE VIEW
BACK VIEW
Screen
TOP VIEW
SW
Floor
* How to install a projection lens?
The projector is supplied without any lens.
The following lenses are available as an option :
HD(1.2:1)
HD(2.2:1)
HD(3.3:1)
HD(4.0:1)
HD(5:1)
HD(7:1)
HD(1.5-3:1)
HD(3.0-5.3:1)
WHD(3.5:1)
How to install the lens?
Remove the foam rubber in the opening of the lens holder.
- Take the new lens out of its shipping carton and remove the lens
covers.
- Turn the lens into the lens holder by turning clockwise.
- Focus the lens (see appendix B) and secure the correct position
with the fastener ring by turning this ring clockwise.

Location and Functions of Control
4-1
5975338 BARCOVISION 9200 210497
4LOCATION AND FUNCTIONS OF CONTROL
Front panel terminology
RS 232 IN REMOTE
PROJECTOR MODE :
GREEN - OPERATION
RED - STANDBY
COM MUNICATI ON PORT
(800-PERIPHERALS)
RS232OUT
0I
Thisd evicec omplies with Part 15 o ft he FCC rules. Ope ration
is subject to f ollowing two co ndit ions :
(1) This device may not cause harmful interference
(2) Thisdevice must accept anyinter ference received
including interference tha t maycau seu ndesired operation
23 4
9
11
10
15
6 7 8
IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS
CODE
IR-RECEIVER
12 13
IR-Received : IR signals are received but not recognized
by the projector.
Diagnostics code : a) source number
b) error code : a two digits error code is displayed when
something goes wrong inside the projector.
IR receiver : receiver for control signals transmitted from
the RCU.
Power switch : '1' = on, '0' = off
Power input : autoranging from 200 to 240 Vac.
Identification plate : name, serial number, art. number.
Voltage identification plate : name, serial number, art.
number.
1
2
3
RS232 IN : to allowcommunication withexternal compu-
ter, e.g. IBM PC or compatible, Macintosh ...
RS232OUT:usedtoconnecttonextprojector,RS232IN
plug (communication link for PC or MAC to the next
projector).
Communication port : allows communication with the
800 peripherals.
Remote : remote input for wired remote control.
Projector mode indication : indicates the status of the
projector.
no lighting up : power switch is not pressed.
red lighting up : power switch is pressed, projector in
stand by mode.
green lighting up : projector in operational mode.
IR-Acknowledged : IR signals are recognized.
4
5
Control Panel Terminology
a. Local keypad
Getting access
6
7
8
9
10
11
12
13
The keypad is located behind a door, screened with the name
of the projector.
To open the door, push once on the indicated side of the door
and turn it to the front side of the projector.

Location and Functions of Control
4-2 5975338 BARCOVISION 9200 210497
b. Remote control
Thisremotecontrolincludesabatterypoweredinfrared(IR)transmit-
ter that allows the user to control the projector remotely.
This remote control is used for source selection, control, adaptation
and set up. It includes automatic storing of :
- picture controls (Brightness, Sharpness...)
- settings
Other functions of the remote control are :
- switching between standby and operational mode.
- switching to "pause" (blanked picture, full power for immediate
restarting)
- direct access to all connected sources.
- variable adjustment speed : when pushing continuously on the
control stick or the picture keys, the adjustment will be executed
in an accelerated fashion.
-
+
-
+
-
+
-
+
-
+
0
9
78
6
5
43
2 1
ENTER
14
13
12
9
8
1
2
3
4
5
7
15
32a
PAUSE
-
+
PHASE
FREEZ
10
11
TEXT
EXIT
ADJ
STBY
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
HELP
?
6
COLOR
PHASE
SHARPN TINT BRIGHTN
STANDBY
ENTER
TEXT
EXIT
PAUSE
2
1
4
3
5
6
8
0
9
7
CONTRAST
7
9
8
10
5
12
13
14
4
15
Remote Control (RCU)
Local keypad
Terminology
Back light key : when activated, all keys will be lighted up
and visible in the dark.
ADJ.:ADJUSTkey,usedtodisplayonlinehelpwhileinthe
adjustment mode.
Addresskey(sunkkey),toentertheaddressoftheprojector
(between0and9). Pressthesunkaddresskeywithapencil,
followed by pressing one digit button between 0 and 9.
STBY : stand by button - to start projection when the
power switch is switched on.
- to switch off the projector
without switching off the power switch.
PAUSE :to stopprojectionfor ashort time, press'PAUSE'.
Theimagedisappearsbut fullpowerisretainedforimmedi-
ate restarting.
Help : on line help information
Digit buttons : direct input selection.
Picture controls : use these buttons to obtain the desired
picture analog level (see also 'Controlling').
PHASE : used to remove the instability of the image.
TEXT:whenadjustingoneoftheimage,e.g.controlsduring
a meeting, the displayed bar scale can be removed by
1
2
3
4
5
6
7
8
9
10
pressing 'TEXT' key first. To re-display the bar scale on the
screen, press 'TEXT' key again. 'TEXT' key only active in
operational mode.
FREEZ : press to freeze the projected image.
ENTER : to start up the adjustment mode or to confirm an
adjustment or selection in the adjustment mode.
EXIT : to leave the adjustment mode or to scroll upwards
when in the adjustment mode.
Control disk (on RCU) or '+' and '-' keys (cursor keys): to
make menu selections when in the adjustment mode.
The control disk can move forward, backward, to the right or
to the left.
Comparisionbetweencontrolstickmovementandtheuseof
the cursor keys on the local keypad :
RCU = local keypad
control disk up = '+' key up
control disk down = '-' key down
control disk to the right = '+' key right
control disk to the left = '-' key left
Use the'+'and'-'keys(cursorkeys):toincreaseordecrease
the analog level of the image controls when they are first
selected.
RC operating indication : lights up when a button on the
remotecontrolispressed. (Thisisavisualindicatortocheck
the operation of the remote control)
11
12
13
14
15

Installation Set Up
5-1
5975338 BARCOVISION 9200 210497
5INSTALLATION SET UP
The projector can be installed to project images in four different
configurations : front/table, front/ceiling, rear/table and rear/ceiling.
Front/Table
Front/Ceiling
Rear/Table
Rear/Ceiling
When switching on and the projector displays an image as illustrated below, an
adaptation of the projector configuration is required.
•
•
•
The projector's configuration can easily be changed with the RCU or the local keypad.
Start up the menu driven procedure by pressing ENTER to display the Main Menu.
To change the Configuration, enter the adjustment mode by pushing ENTER.

Installation Set Up
5-2 5975338 BARCOVISION 9200 210497
Push the control disk up or down to highlight Systems Settings and press ENTER.
ENTER displays the System Settings menu.
EXIT returns to operational mode.
Push the control disk up or down to highlight Installation and press ENTER.
SYSTEM SETTINGS
•
Lamp Control
Installation
Input slots
Summary
Color
ENTER displays the Installation menu.
EXIT returns to the Main menu.
A marker indicates the actual configuration. Push the control disk up or down to
select the corresponding configuration with regard to the projector environment.
Press ENTER to confirm your selection. The marker jumps to the selected item
and the image changes. Press EXIT EXIT EXIT (3x EXIT) to return to opera-
tional mode. INSTALLATION
•
Front/Table
Front/Ceiling
Rear/Table
Rear/Ceiling
MAIN MENU
832b
Picture Control
Audio Control
System Settings
File service
Service Mode

Connections
6-1
5975338 BARCOVISION 9200 280497
6CONNECTIONS
RS232OUT
IR-ACKNOWLEDGED
IR- RECE IVED
DI AG NOS TI CS
CODE
IR- RECE IVER
100 - 230 V
9 - 4 A
60 - 50 H z
0 I
ThisdevicecomplieswithPart15oftheFCCrules.Operation
issubjecttofollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference
(2)Thisdevicemustacceptanyinterferencereceived
includinginterferencethatmaycauseundesiredoperation
Power (mains) cord connection
Use the supplied power cord to connect your projector to the wall
outlet. Plug the female power connector into the male connector at
the front of the projector.
The power input is auto-ranging from 200 to 240 VAC.
This projector may be connected to an IT-power system.
Fuses
Warning
For continued protection against fire hazard :
- refer replacement to qualified service personnel
- ask to replace with the same type of fuse.
Fuse type : T12.5 AH/250V
CONTRASTCOLORPHASE
SHARPN TINT BRIGHTN
STANDBY
ENTER
TEXT
EXIT
PAUSE
2
14
3
5
6
8
0
9
7
Stand by button
ADJ EXIT
STBY TEXT
BRIGHTNESS
- +
-
+
-
+
-
+
SHARPNESS
-
+
TINT
COLOR
CONTRAST
FREEZ
0
9
78
6
5
43
2
1
ENTER
PAUSE
-
+
PHASE
HELP
Switching on
Use the power switch to switch on.
When '0' is visible, the projector is switched off.
When '1' is visible, the projector is switched on.
When switching on with the power switch, the projector starts in the
stand by mode. The projector mode indication lamp is red.
To start image projection :
a. press the 'Stand by' button on the local keypad or on the remote
control. The projector mode indication lamp will be green.
b. press a digit button to select an input source. The projector mode
indication lamp will be green.
RS232OUT
IR-ACKNOWLEDGED
IR-RECE I VED
DI AGNO STI CS
CODE IR-RECEIVER
100 - 230 V
9 - 4 A
60 - 50 H z
0 I
ThisdevicecomplieswithPart15oftheFCCrules.Operation
issubjecttofollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference
(2)Thisdevicemustacceptanyinterferencereceived
includinginterferencethatmaycauseundesiredoperation
Projector mode indication
RS 232 IN
COMMUNICATION PORT
(800-PERIPHERALS)
RS232 OUT
0I

Connections
6-2 5975338 BARCOVISION 9200 280497
When the total run time of the lamp is 970 hours or more, the following message will be
displayed for 1 minute. This message will be repeated every 30 minutes. Press EXIT to
remove the message before the minute is over.
Whenthe totalrun timeof the lampis 1000hours ormore, the followingmessage, withthe
exact run time is displayed on the screen.
Lamp run time is 1000 hours. Operating the lamp longer than 1000 hours may damage
the projector. Please replace the lamp.
When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.
Thetotallifetimeofthelampfora safe operation is1000hoursmax.(normalpowermode).
Donot use itlonger. Replace always with asame type oflamp. Calla BARCOauthorized
service technician for lamp replacement.
Warning : Using a lamp for more than 1000 hours is dangerous, the
lamp could explode.
Lamp run time
980 h
Input connections.
The projector has modular input facilities. The input slots
can be filled up with the following modules :
Video, S-video (PAL, SECAM, NTSC) input
order no. R9827900
RGBS/RGsB analog input
order no. : R9827910
RGB3S/RG3sB input
order no. : R9827920
Component Video input
order no. : R9827930
The sequence of insertion has no importance. It is even
perfectly possible to insert several input modules of one
type.
Note : When using RCVDS05 or VS05, the input
configuration of the projector must be as follows:
Slot 1 : video input module
Slot 2 : RGB analog input module
Slot 3 : Component input module
Input module insertion into the projector :
- Power down the projector and disconnect the power cord
from the wall outlet.
- Remove the dummy plate covering the chosen input slot
by turning out both screws.
- Slide the input module in the free slot. Insure the module
is seated correctly in the guide grooves.
- Press on both handles of the input module until the
module plug seats in the connector of the projector.
- Secure the input module by tightening both retaining
screws.
-Reconnect the powercordto thewalloutlet andswitchon
the projector.
RS232 OUT
IR-ACKNOWLEDGED
IR-REC EIVE D
DIAG NOSTI CS
CODE IR-RECEIVER
100- 230 V
9 - 4A
60 - 50 Hz
0 I
Thi s devi ce co mpl i es w i t h P ar t 15of the F C C rul es. O per at ion
is s ubj ec t to f ol l owi ng t wo c o ndi t i o ns :
(1 ) T h i s d evi c e m ay n ot c aus e har m fu l i n t erf er en ce
(2 ) T h i s devi ce m ust accept an y i nter f er ence re ceiv ed
in cl ud i ng i nt er f er enc e th at m ay cau se u nde si r e d o per at i o n
Switching to stand-by.
When the projector is running and you want to go to stand-by, press
the stand-by key.
Switching off
To switch off:
- press first STANDBY key and let cool down until the fans
stop blowing ( or at least 15 min).
- switch off the projector with the power switch.
WARNING:Whenswitchingtostandby,neverrestartprojection
(hot restrike) within the first 3 minutes to avoid damage to the
lamp.
The new installed module can be selected with the digit buttons on
the RCU or the local keypad.
WARNING
Lamp run time is 1000 hours
Operating the lamp longer
than 1000 hours may damage
the projector.
Please replace the lamp
OK