Barrette Bolton 73025736 User manual

INSTALLATION INSTRUCTIONS
Ready-to-Assemble
Privacy Vinyl Fence
Ready-to-Assemble
Privacy Vinyl Fence
Ready-to-Assemble
FREEDOM-WEB
Read all instructions prior to installing product.
Refer to manufacturers safety instructions when operating any tools.
To register your product, please visit:
freedomproduct.com

2
Posts
Post Tops
Concrete
Coarse Gravel (6" per hole)
Post Hole Digger/Shovel
String Line Stakes with String
Level
Tape Measure
Rubber Mallet
Safety Glasses
Glue
TOOLS/MATERIALS NEEDED:
BEFORE YOU BEGIN:
Check your local zoning laws.
• Local zoning laws and Home Owners
Associations may regulate the location, style
and height of your fence or even require a
permit signoff beforehand.
• Check local codes for frost line depth and
regulations.
• Additional products and assembly may be
required to meet wind code requirements.
Notice of acceptance (NOA) can be found at
www.miamidade.gov/building/pc-search_app.asp
Contact your local utilities companies.
• You must have the utility companies clearly
mark your property for electrical, gas or
water lines to avoid puncturing any unseen
underground utilities.
WARNING:
• Improper installation of this product can result in personal injury. Always wear safety goggles when
cutting, drilling and assembling the product.
• Incorrect installation may cause harm to the product or individual.
• Check local building codes to determine pool-safe fencing options.
NOTICE:
• DO NOT attempt to assemble the kit if parts are missing or damaged.
• DO NOT return the product to the store. For assistance or replacement parts call: 1-800-336-2383.
Component list:
Description
Rails
Boards
U-Channels
Pickets*
Lattice*
Full Privacy
Closed Top
Open Top Scallop
Open Top Straight
Lattice Top
*Included depending on style
To obtain and review a copy of the warranty please go to: Freedomproduct.com/warranty. You can also
contact 1.888.418.4400 or write to Freedom Outdoor Living, 7830 Freeway Circle, Middleburg Heights,
Ohio 44130 to obtain a copy of the warranty.

3
1
2
3
Post Location:
Measure the width of the fence panel (X) plus the width
of the post (Y). This is the common center-to-center
measurement (unless there is a cut-down panel) for post
hole location (Fig. 2).
Post Installation:
Dig the rst two post holes. Hole size should be dug based
on the following determination: Depth is determined by
your local frost line measurements plus 6" for gravel/ller
(Fig. 3). Width is determined by the post size. See chart
below for measurements:
Diameters based on post size:
10" for 5" x 5" post
8" for 4" x 4" post
Fig. 2
5x5 Post
5x5 Post
Example:Example:
Frost Line
Gravel/
Filler
6"
10"
X+Y
Y
X
Fig. 3
Insert 6" of gravel/ller into the bottom of both holes and
then set both posts into the ground and level the rst post.
Add wet or dry concrete mix according to manufacturer’s
instructions to the top of the rst post hole. Make sure
panel will be 2" above the ground (Fig. 4)
After setting rst fence section, proceed systematically
with post, panel, post, etc.
Fig. 4
Post
Concrete
Gravel
Mark the fence location using string and line stakes (Fig.
1).
NOTE:
Plan gate placement, opening and hardware
clearance before installing fencing.
Fig. 1

4
4
5
6
7
When included in kit, place aluminum insert into bottom
rail, then insert bottom rail into bottom post route hole
of rst post only (Fig. 5). Panels with 7" rails do not
require aluminum inserts.
Attach U-channels to two end boards (Fig. 6).
NOTE:
Attach U-Channel to "tongue" side of rst board, and
"goove" side of last board.
Insert boards into bottom rail ensuring U-channels are
on both ends. Start from rst installed post and work
towards second post (Fig. 7).
For Full Privacy Panels:
Insert the top rail into the rst top hole post route then
guide over top of boards (Fig. 8).
Proceed to Step 15.
Fig. 5
Fig. 6
Fig. 7
Fig. 8
U-Channel
U-Channel
First
Board
Last
Board

5
8
9
10
11
12
For Lattice Top Panels:
Add the lattice insert over the top of the lattice
(Fig. 9).
Place lattice into the middle rail followed by the top rail.
Fig. 9
Top Rail
Middle Rail
Lattice Insert
Lattice
Finally, add the completed top assembly into the route
holes of the rst post (Fig. 10).
Proceed to Step 15.
For Closed Top Panels:
Insert pickets into middle rail (Fig 11).
Fig. 10
Fig. 11
Middle Rail
Pickets
Guide top rail over picket tops (Fig. 12).
Fig. 12
Top Rail
Top Rail
Finally, add the completed top assembly into the route
holes of the rst post (Fig. 13).
Proceed to Step 15.
Fig. 13

6
For Open Top Panels with Pickets:
Attach middle rail into left side of post route only then
guide rail over boards. Insert top rail into left post route
holes of rst post only (Fig. 14).
Insert pickets down through top and middle rail (Fig. 15).
NOTE:
Scalloped and Arched panels have pickets/boards
that are numbered. Start from left side with the #1
picket/board rst.
Fig. 14
Fig. 15
Apply glue on inside rim of post tops then attach to
posts (Fig. 17). Repeat these steps until completed.
Fig. 17
Insert the completed fence panel into the route holes of
the second fence post. Plumb and level the post and add
concrete according to
manufacturers instructions to top
of hole (Fig. 16).
Fig. 16
13
14
15
16

BARRETTE OUTDOOR LIVING
7830 FREEWAY CIRCLE
MIDDLEBURG HEIGHTS, OHIO 44130
TEL: [phone]
WWW.FREEDOM.BARRETTEOUTDOORLIVING.COM