Zippity WASHINGTON VINYL PICKET FENCE User manual

1
www.zippity-outdoor.com
ASSEMBLY
INSTRUCTIONS
WASHINGTON VINYL PICKET FENCE
KIT -2 PACK (30in H x 42in W)
45 MIN approximate assembly
time for 2 fence panels
6935 Reames Rd. Ste. K. Charlotte, NC 28216
[e-mail]
704-892-5222 / 877-234-6196
zippity-outdoor.com
@

2www.zippity-outdoor.com
GENERAL INFORMATION
IMPORTANT
• Please read through before starting assembly.
• Important: Check the inside of the larger pieces in your box for other materials packed inside.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
MISSING OR DAMAGED PARTS?
CALL US FIRST SO WE CAN HELP YOU RIGHT AWAY!
Although great care has been taken to ensure proper packaging and handling of this product, occasionally problems occur.
If you discover any missing, damaged or defective parts, please contact our customer service department.
EMAIL: [e-mail]
PHONE: [phone]
Customer service agents are available to take calls weekdays from 8am-5pm EST.
To help you quickly and accurately, please have reference item number ZP19048 and the specic part name which can be
found on the next page. It is helpful if you can provide the batch lot which is a stamped number on the end of the box.
NEED ASSEMBLY HELP?
If you are having problems with the assembly or installation of this product, we are happy to assist you with the process, so
please give us a call at 704-892-5222/877-234-6196.
NEED TO RETURN?
If for some reason you need to return this product, please allow us to help resolve your issues rst. If you still decide to
return the product, you will need to intitate the return from the company you originally purchased from.
@

3
www.zippity-outdoor.com
STEP 1: LAY OUT MATERIALS
WASHINGTON VINYL PICKET FENCE KIT (2 PACK) COMPONENTS
TOOLS YOU WILL NEED
A
C
E
B
D
F
G
H
I
Post Caps (4)
Top Rails (2) -
1 ½” x 1 ½” x 41 ¾”
Picket #1 (4) -
¼” x 1 ¼” x 25 ½””
Picket #2 (4) -
¼” x 1 ¼” x 23 ¼”
Picket #3 (4) -
¼” x 1 ¼” x 21 ¾”
Picket #4 (4) -
¼” x 1 ¼” x 21”
Posts (4) -
7
/ 8 ” x 1 ½” x 39 ½”
Bottom Rails (2) -
1 ½” x 1 ½” x 41 ¾”
Rail End Caps (8)
(4 are installed,
4 are loose)
¾” Stainless Steel
Screws (16)
(Bag A)
1” Stainless Steel
Screws (8)
(Bag B)
Joiner Clips (4)
Cordless Drill
Level

4www.zippity-outdoor.com
STEP 2: ASSEMBLE THE FENCE FRAME
STEP 2.1
STEP 2.2 STEP 2.3
Identify the top rail (Part C) and the bottom rail (Part D) and position them as shown below. Pressure t two loose
rail end caps (Part B) into the ends of each rail.
Slide (2) posts (Part F) down into the routed
holes in the horizontal rails.
Align the pre-drilled holes in the posts and
the rails. Screw the top and bottom rails into
the front and back of the posts using a total
of (8) ¾” screws (Part H).
Bottom rail has no picket
holes on underside of the rail.
Note: Ensure picket
holes on the bottom
rail are facing up.
Orient the bottoms of the posts as shown
Align Holes

5
www.zippity-outdoor.com
STEP 3: INSERT THE PICKETS
STEP 4: ASSEMBLE THE SECOND FENCE PANEL
STEP 3.1
STEP 4.1
The pickets (Part E) are numbered at the bottom 1, 2, 3, and 4 to create a scallop pattern. Lay out your pickets in the
order shown below. Insert the pickets into the rail as illustrated.
Repeat Steps 2 and 3 to assemble the second fence panel.
Note: The tabs on the bottom of the pickets go
into the bottom rail to lock the picket into place.
1
1
2
2
33
44

6www.zippity-outdoor.com
STEP 5: INSTALL FENCE INTO GROUND
STEP 5.1 Move the fence to its nal location and identify
the location of the posts.
STEP 5.2 Attempt to push the unit into the ground
as illustrated.
Optionally:
1. If your ground is too hard, loosen the top 6”or 7”
of the ground with a claw hammer as illustrated.
2. Add water to loosened soil.
3. Use a block of wood to protect the top of the post
and gently hammer the post into the ground.
Push down on the top of posts
with both hands
x
x
Option 1:
Option 2:

7
www.zippity-outdoor.com
STEP 5.3 Level the assembled unit, backll, and compact dirt around the base of each post to strengthen the unit.
Level

8www.zippity-outdoor.com
STEP 6: FASTEN JOINER CLIPS
STEP 6.1 Fasten the fence panels together using the joiner clips (Part G) and the 1”self-augering screws (Part I)
as illustrated below.
Angled Fence
Application
Corner Fence
Application

9
www.zippity-outdoor.com
STEP 7: ATTACH POST CAPS
STEP 7.1 Push the post caps (Part A) over the top of the posts to complete the assembly. The post caps will lock into place
when pushed over the posts.
6935 Reames Rd. Ste. K. Charlotte, NC 28216
[e-mail]
704-892-5222 / 877-234-6196
zippity-outdoor.com
@