Turnstiles OTSG9000 Series User manual

User Manual
Speed gates OTSG9000 series
Applicable Model(s): OTSG9000, OTSG9011, OTSG9022,
OTSG9033, OTSG9200, OTSG9211, OTSG9222, OTSG9233
Version: 1.0
Date: June 2019

Contents
1. Product Introduction............................................................................................................................................................. 1
1.1 Model number and access control...................................................................................................................... 1
1.2 Chassis design and dimensions............................................................................................................................. 1
1.3 The mechanical system of the speed gates .................................................................................................. 2
1.4 Electric control system................................................................................................................................................. 2
1.5 Operation principle of the speed gates............................................................................................................ 3
1.6 System composition of the product................................................................................................................... 4
1.7 Specifications...................................................................................................................................................................... 4
2. Installation of the Product.................................................................................................................................................. 5
2.1 Installation notes.............................................................................................................................................................. 5
2.2 Installation position of the speed gates ........................................................................................................... 5
2.3 Cables installation and fixing................................................................................................................................... 6
3. Menus .............................................................................................................................................................................................. 9
3.1 Menu operations.............................................................................................................................................................. 9
3.2 Menus...................................................................................................................................................................................... 9
3.3 Functions introduction of wiring and terminal.........................................................................................12
4. Troubleshooting .....................................................................................................................................................................13
5. Product Maintenance..........................................................................................................................................................14
5.1 Chassis...................................................................................................................................................................................14
5.2 Movement..........................................................................................................................................................................14
5.3 Power.....................................................................................................................................................................................14
www.TURNSTILES.us | [email protected] | 303-670-1099
1

1.1 Model number and access control
Access
Model
None C3-200 and
2*Wiegand reader
inBio 260 and 2*
FR1500/ID reader
2*Facedepot 7B
device
OTSG9000 √
OTSG9011 √
OTSG9022√
OTSG9033√
OTSG9200√
OTSG9211 √
OTSG9222 √
OTSG9233 √
Figure 1-1
1.2 Chassis design and dimensions
The SUS304 stainless steel body looks simple and clean and is anti-corrosion.The turnstile grants
legal access to the authorized persons and restricts illegal access. In case of an emergency, the lock
will release to allow fast evacuation and egress.
Below isthe design and dimensions of OTSG9000:
www.TURNSTILES.us | [email protected] | 303-670-1099
2

Figure 1-2
1.3 The mechanical system of the speed gates
The mechanical system of the swing turnstile is composed of the cabinet and the core mechanism.
The cabinet is equipped with the mode indicator, the infrared sensor, and the locking system. The
core mechanism mainly consists of the motor, the chassis, the core, and the swing arm (the glass
panel).
1.4 Electric control system
The electric control system of the swing turnstile is mainly composed of the master control panel, the
infrared sensor, the mode indicator, and the loudspeaker.
Master control panel: The master control panel is the core part of the control system that receives
signals from the photoelectric switch, performs logical judgment and processing of these signals, and
issues executive commands to the mode indicator, the servo motor driver and the loudspeaker.
Infrared sensor: It detects the location of the pedestrian and plays a safe protection function.
Mode indicator: This indicator shows the current passing mode status of the channel and guides the
passenger to pass the passage orderly and safely.
Loudspeaker: The system will trigger the alarm if it detects any unauthorized entry to the lane.
www.TURNSTILES.us | [email protected] | 303-670-1099
3

1.5 Operation principle of the speed gates
When the device is connected to the power, the system will perform self-check. The device will
operate normally if no problem is detected. If a failure is detected, the system will display related
messages on the LCD display screen so that the user can have a quick knowledge of and solve
the problem.
Figure 1-3
When the reader detects a valid card/fingerprint, the display screen will show whether it is
successful or not. And the switch instruction signal is transmitted to the master control panel.
After receiving the signal from the reader and the infrared sensor, the master control panel will
send valid control signals to the servo motor driver. At this time, if the system is in forbidden
passing mode, the mode indicator light will turn red, and the master control panel will not accept
signals of card swiping/fingerprint scanning.
After the passenger passes the channel according to the opening direction of the swing arm, the
infrared sensor will keep detecting the movement of the pedestrian throughout the passage and
continue to deliver signals to the main control panel until the pedestrian passes through the
passage.
If the pedestrian enters the passage but forgets to swipe his/her card, or if the card held by the
passenger is invalid, the system will prompt an audible alarm to warn the pedestrian to stop
passing. The alarm signal will not be cancelled until the passenger retreats from the passage. A
pedestrian can pass through the lane only after successful verification with a valid card read by
the card reader.
Air switch
www.TURNSTILES.us | [email protected] | 303-670-1099
4

1.6 System composition of the product
The single-passage management system is composed of two single-core speed gates. The multi-
passage management system is composed of two single-core barriers and multiple dual-core barriers.
Working modes of the system
To meet different needs, this system provides multiple working modes for users, including the normal
working mode, normally open mode, normally closed mode, and testing mode.
After supplying power to the device, the LCD screen on the control board will display a default state,
which is the current working mode.
1.7 Specifications
Dimension (mm) H1000: L = 1600, W =120, H = 1022
Communication CAN Input voltage AC110~240V, 50-60Hz
Input control signal Switching signal Output voltage DC 24V
Time of
opening/closing 0.8 Sec (adjustable) Relative humidity 20% - 95%
(Non-condensing)
Temperature -28℃to 60℃Passage rate Maximum 30/minute
Infrared sensor 10 Working environment Indoor
www.TURNSTILES.us | [email protected] | 303-670-1099
5

2. Installation of the Product
2.1 Installation notes
1) It is recommended that the speed gates must be installed on a horizontal solid platform with a
height of 50mm to 100mm.
2) It is also recommended that the swing turnstile should not be used in a corrosive environment.
3) Make sure the protective ground wire of the system is reliably connected to avoid personal
injuries or other accidents.
4) The equipment shell is made of stainless steel. You may gently remove any dirt or dust on the
surface with a soft and smooth fabric. Do not scrub the surface with hard objects. Do not rinse
the device with water, otherwise there may be short circuit or damaging the equipment.
5) After installation, check if the connection is done correctly at the connecting points of the
protective ground wire, at the connector assemblies and wiring points of the circuits, as well as at
each movable part of the speed gates turnstile. Any loose nuts, screws and other fasteners should
be tightened in time to avoid speed gates turnstile failures caused by longer operations.
2.2 Installation position of the speed gates
A distance of 100mm between the speed gates turnstile and the wall needs to be reserved for ease of
opening the top cover of the machine to perform maintenance and adjustment. The reference figure
is shown below:
www.TURNSTILES.us | [email protected] | 303-670-1099
6

Figure 2-2
2.3 Cables installation and fixing
For the outlets of the concealed cables, please refer to the drawing indicating the mounting holes.
The input voltage for this swing turnstile is AC110-220V, and its master and slave are connected with
an 8-core cable (signal) and a2-core cable (power).When installing thespeed gates turnstile, the
user only needs to connect it to the corresponding ports. Note that the PVC conduits are laid 100mm
under the ground, with the height of the exposed part not exceeding 100mm. In addition, the
conduit outlet is bent to prevent the ingress of water into the conduit.
Installation holes and cabling positions are as shown inFigure 2-3a:
www.TURNSTILES.us | [email protected] | 303-670-1099
7

Figure 2-3a
Mark the anchor hole at the centre of the stand, and the edge of the chassis base on the ground
according to the size as shown in Figure 2-3a. Use a hammer drill to drill M12 screw holes, then install
the screws. Place the swing turnstile according to the size and respective installation position as
shown in the figure before installation and fixing. Connect the turnstile to the power supply and
www.TURNSTILES.us | [email protected] | 303-670-1099
8

perform a power-on test. If the test is passed, tighten the screws. It is recommended to mark a
warning line on the ground, as shown in Figure 2-3b, after installing the device to remind the
pedestrian to stand behind the line when swiping the card.
Figure 2-3b
www.TURNSTILES.us | [email protected] | 303-670-1099
9