Bass Habit Play SPL64 User manual

SPL64
SPL84
SPL Play Loaded Enclosure

Thank you for purchasing this Bass Habit product. Please read this manual in order to understand how to get
the best result from this product and ensure that the advices on how to look after the product and the safety
precautions are followed. We hope you enjoy using the product as much as we enjoyed creating it.
DO NOT EXPOSE THIS PRODUCT TO EXCESSIVE DAMP OR MOISTURE
- Doing so may result in fire, shock or damage to the product.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE POSITIVE BATTERY TERMINAL
- Failure to do so may result in electric shock or injury.
ENSURE GOOD AND CORRECT CONNECTIONS
- Failure to make the correct connections may result in permanent damage to the product.
DO NOT USE ANY FUNCTIONS THAT MAY TAKE YOUR CONCENTRATION AWAY FROM DRIVING YOUR VEHICLE
- Do not set up your amplifier whilst driving. Doing so may result in an accident. For prolonged interaction
with the product, make sure that your vehicle is stationary and parked in a safe location.
KEEP THE VOLUME AT A LEVEL SO YOU CAN STILL HEAR OUTSIDE NOISE
- Failure to do this may result in an accident. Bass Habit equipment is capable of producing sound levels
that can permanently damage your hearing. Bass Habit recommends caution when listening at a high
volume. For safety and enjoyable listening, the sound should be clear without distortion.
CAUTION
Never connect any speaker lead to the car chassi. This can cause severe damage to your car audio set up.
Before drilling or cutting any holes, investigate the layout of your vehicle thoroughly.
Use caution when working near the fuel/hydraulic lines and electrical wiring.
Observe the correct polarity when wiring. Improper phasing may cause a loss of bass response.
Ensure that no moving parts catch on the speaker or grill (e.g. door handles or window glass inside the door).
WARRANTY
All Bass Habit products carry a full warranty depending on the conditions in the country where it is sold. The
warrany is valid from the date of the original receipt as proof of purchase (warranty period differs depending
on local warranty laws and policies). Contact your international Bass Habit dealer or distributor concerning
specific procedure for your country’s warranty policies.
WHAT IS NOT COVERED
• Damage to product due to improper installation.
• Subsequent damage to other components.
• Damage caused by exposure to moisture, excessive heat, chemical cleaners and/or UV radiation.
• Damage through negligence, missuse, accident or abuse. Repeated returns for the same fault may be
considered as abuse.
• Any cost or expense related to the removal and/or abuse. Repeated returns for the same fault may be
considered as abuse.
• Damage caused by amplifier clipping or distortion.
• Items repaired or modified by any unauthorised repair facility.
• Return shipping on non-defective items.
• Products returned without a return authorisation number.
• Damage to product due to use of sealant.
WARNING
Bass Habit equipment is capable of sound pressure levels that can cause permanent damage to your hearing
and those around you. Please use common sense when listening to your audio system and practice safe
sound.
INTERNATIONAL TECHNICAL ENQUIRIES
For international technical support please contact the distribution agent for your country.

INSTRUCTIONS
INSTALLATION EXPERIENCE
Installation of Bass Habit products may require experience with a variety of mechanical procedures including
enclosure construction. This manual only provides general installation and operation instructions. If you have
any reservations about your installation skills, please contact your local authorized Bass Habit dealer for help.
CHOOSING LOCATION FOR YOUR SPL LOADED ENCLOSURE
Choosing a good placement of your Bass Habit product will have the greatest effect of the sound quality of
the system. There are many different considerations needed when choosing the location(s) that best meet
your needs. The location(s) must be large enough for the enclosure to fit. Care is needed to ensure that the
desired location will not affect either the mechanical or electrical operation of the vehicle.
INSTALLATION PRECAUTIONS
NOTE! Proceed only if you are a qualified installer, otherwise let your dealer do it.
• Always wear protective eyewear when using tools.
• Turn off all stereo and other electrical devices before you begin.
• Disconnect the (-) negative lead from your vehicle’s battery.
• Never use force when installing a Bass Habit product.
• Locate all fuel lines, brake lines, oil lines and electrical cables when planning your installation.
2 Ohm 2 Ohm
IN-IN+IN+IN-
WIRING DIAGRAM

Component
Configuration
RMS Power
MAX Power
Nominal Impedance
Freq. Response
Sensitivity
Enclosure material
SPL Loaded Enclosure
4xSP165M & 2xSP25A
360W
880W
2+2 Ohm
110Hz - 20Khz
96 dB
MDF
SPECIFICATION SPL64
Enclosure type
Enclosure volume
Terminal
Ported/ Fb 118 Hz
2x7L
Single / 2 pcs
Dimension (LxWxH) 920x199x175/74 mm

Component
Configuration
RMS Power
MAX Power
Nominal Impedance
Freq. Response
Sensitivity
Enclosure material
SPL Loaded Enclosure
4xSP200M & 2xSP25A
380W
960W
2+2 Ohm
80Hz - 20Khz
97 dB
MDF
SPECIFICATION SPL84
Enclosure type
Enclosure volume
Terminal
Ported/ Fb 85 Hz
2x12,8L
Single / 2 pcs
Dimension (LxWxH) 1080x236x216/88 mm

DRIVER SPECIFICATIONS
Component
Size
RMS Power
MAX Power
Nominal Impedance
Freq. Response
Sensitivity
Frame material
SP165 Midrange
165mm (6,5")
70W
180W
4 Ohm
110Hz - 12Khz
95 dB
Steel
Cone material
Suspension material
Magnet
Paper
Cloth
Ferrite
Voice Coil Wire Aluminium
Voice Coil Diameter 25mm (1")
Component
Size
RMS Power
MAX Power
Nominal Impedance
Freq. Response
Sensitivity
Frame material
SP200 Midrange
200mm (8")
75W
200W
4 Ohm
85Hz - 12Khz
96 dB
Steel
Cone material
Suspension material
Magnet
Paper
Cloth
Ferrite
Voice Coil Wire Aluminium
Voice Coil Diameter 25mm (1")

DRIVER SPECIFICATIONS
Component
Size
RMS Power
MAX Power
Nominal Impedance
Freq. Response
Sensitivity
Frame material
SP25A Bullet Tweeter
25mm (1")
40W
80W
4 Ohm
2KHz - 20Khz
100 dB
Aluminium
Cone material Aluminium
Magnet Ferrite
Voice Coil Wire Aluminium
Voice Coil Diameter 25mm (1")

The crossed-out wheelie bin symbol means that the product, literature and packaging included must be taken to
separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste:
dispose of them at a recycling point. For info on your nearest recycling point, check with your local waste
authority.
Winn Scandinavia reserves for possible typos, factual or numeric errors that may have been printed on any
products, package designs, user manuals and/or other included accessories.
Products marked with the RoHS symbol complies with the relevant provisions of the RoHS Directive for the
European Union. In common with all Electrical and Electronic Equipment (EEE) the product should not be
disposed of as household waste. Alsternative arrangements may apply in other jurisdictions.
The product with the CE mark indicates that it has passed the correspondning conformity assessment procedure
and the manufacturer’s declaration of conformity, and it complies with the relevant EU directives, and is used as
a pass for the product to be allowed to enter the European Community market. Relevant directives require
industrial products to be affixed with the CE mark. Those that do not have the CE mark shall not be marketed.