Baumr-ag Md1101 User manual

MAGNETICDRILL MD1101

1

UserManual

Weappreciateyouchooseourmagneticdrill.Ourmagnetic drillcanuseoncomplexenvironment

forsteeldrilling operations, especiallyfortheshipbuildingindustry,paperindustry, bridges

industry,machineryequipmentinstallation,steelstructureworks,subwayconstruction,large

equipmentmaintenance, powerplantmaintenanceand allplumbing maintenance.

Features:small size, highpower, high efficient,accurate positioningfeatures.Ourmagnetic drill

motoruse Germanytechnologysothatourmagnetic drillexcellenthigh-powercanwithstand

higher-intensityoperations.You will havenoregrettopurchaseourmagneticdrillbecauseour

productsreallyenjoyhighqualitybothathomeandabroad.It'sno problemforaftersalesservice.

Warning: Beforeyouusemagneticdrill,pleasepayattention toreadprecautionarysafety

listbelowinordertoavoidfire, electricshock, andinjuriesandotheraccidents.

1. Keepworkplaceclean.Dirtyareasinvite injuries.

2.Pleasegiveemphasistotheworkplaceenvironment.Don texposetooltotherain.Don tuse

toolsindampordarkplaces.Donotuse toolsinflammableliquidplace.

3. Preventidlersgointothe workplace.Donotletthe idle andchildrencontactortouchthetools.

4. Whennotuse, toolsshouldbe storedinadry,high,orlocked-up place.Keepoutofthereachof

children.

5. Keepproperratedspeedandpressure tomaketheoperation more safe and durable.

6. Donotletthe toolworkoverload.

7.Donotwearlooseclothing.Theycanbecaughtinmovingtool.Whenworkoutdoors,you

shouldwearrubberglovesandnon-slipsafetyshoes. Frequently operatearerequiredtowear

protective cap.

8. Wearsafetyglasses.Youshouldwearmaskifshavingare manyand dustismany.

9. Donottrample wire.

10.Workmustmaintainproperposture.

11.Checkthewireregularly.Iffinddamagepartwhichneedbereplacedimmediately.Keep

handle dryandclean.

12.Whentoolnotuse, you needtoremove thefixture, andmake sure tounplugthe powercord.

13.Preventaccidentalstart.Inserttheplugintothepowerseat; youmustcheckthetoolswitch

whetherturnedoff. Whenthetoolhaspower,pleasedo notpress theswitchfrequently.

14.Makesuretousetheextensioncordforoutdooruse.

15.Donotuse toolwhenyou aretired.

16.Checkall partsofthe toolbeforeuse.

17.Toavoidelectricshock.Whenwork,thebodycannottouchgroundedmetal,suchassteel

pipes, radiators,refrigerationmachines.

NotePower:Payattentiontothepowersupplyvoltage. Ifthepowersupplyvoltagehigherthan

thevoltageapplication ofthetool,whichwill enableusersa seriousaccidentandwillalsodamage

tools.If thepowerssupplyvoltagelowerthanthetoolsrequired,whichwill beharmfultothe

motor.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

2

Futureand use

Magneticdrill canbeadsorbedon thesteelpartsoftheplane, side, top, surfaces.Itwidelyusedin

construction,bridge,boiler,shipbuilding and otherindustries.Someelectricdrillscannotdrill

inconvenientonlargeironand steelpart,youcanusethemagneticdrill,whichisconvenient,

flexible, and alsocanreduce laborintensityandimprovemachiningaccuratelyand efficient.

Becauseit hasauniquerole thatcandrilllargehole (45 #steelcanbedrilledlargesthole Φ80mm),

soitcanbeinsteadofsome radialdrilling machine.

ⅡPreparationbeforeuse

1. Insertthehandle leverintothehandle seathole andnexttightenthem.

2.Turnthehandle lever,checktheguideboardwhethermovefreely.

3.Connectpowerandopenmagnetdrillswitch,you cansee indicatorlighting,whichshow

magneticdrill isinworking condition.Useascrewdriverorironbarinthebottomofmagnetto

checkwhetherhavesuction.Openthe drill controlswitch,checkthedrill whetherworking.

Note:Whenmovingmagneticdrill,donotdragiton thegroundinordertopreventmagnet

damage.

ⅢSeveralworkingmethodsand precaution

1.Levelwork:

a. Movethemagnetdrillon theworksurface(Note:magnetcontactsurfaceshouldbecleanand

smooth, donothave iron debris)

b. Connectpowerand openmagnetic controlswitch,somagnetfirmlyattachon theworkplace.

c. Installrequireddrill,loosenthedialand tightenthetopscrews,turntherack,sothatthedrill

canaligntheholesand tightenthetop screw. Rotatesupporting bar.

d. Openthedrillcontrolswitch,sothedrillingprocess.(Note:Thefeedisgenerally0.55mm/r,so

nottoomuchforce inordertopreventoverload)

e. Whenprocessing complete, turnoff thecontrolswitchandmagnetcontrolswitchand pickup

magneticdrill fromworksurface.

2. Side work:(Note:Itneedstwoormorepeople operations,andsome people care)

a. Insertthe plugintopoweroutlet.

b.Liftthemagnetdrillandmakethemagnetattachedtheworksurface,openmagnetcontrol

switch,somagnetsuckedtheworksurface firmly.

c. Fastensafetyropeinordertopreventmagneticdrill suddendrop.

d.Install requireddrill,loosenthedialand tightenthetopscrews,turntherack,sothatthedrill

canaligntheholesand tightenthetop screw. Rotatesupporting bar.

e. Openthe drill controlswitch,sothedrillingprocess.(Note:Thefeedisgenerally0.55mm/r,so

nottoo muchforce, topreventoverload;Whenoperation,peopledonotstandunderthemagnet

drillinordertopreventa suddendropwoundingpeople.)

f.Whenprocessingcomplete, turnoffthecontrolswitchandmagnetcontrolswitchand pickup

magneticdrill fromworksurface.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

3

3.Top ofthework(Itneedstwoormorepeopleoperations,and some peoplecare)

4. Otherways:Operatorscanflexibilityuse,butmustconsidersecurity.

ⅣSafeuseandmaintenance

SafetyInstructions

1. Usersmustcomplywiththe instructions

2.Areamustbe clean,light.

3. Balance bodywhenuse tool.

4.Letthe idle and thechildrenawayfromworkplace.

5.Avoidthewires,water,gasoline.

6.Ingeneralworkplace, it need securitymeasures,suchaspowerfailureprotection,leakage

protection,safetyisolation transformer,ortheusermustwearinsulatedglovesandinsulatedmat

insulation.

7. Donotexchange the plugtype.

8.Afteruse, remove the plugintime.

9.Topreventasuddenstart,inserttheplug,thedrill and magnetcontrolswitchshouldbeinoff

position

10.Farawayfrompowersupplyover20m,youneedselectourfactorycabletray(S333,S4332

withleakage protection)

Help

1. Usevoltage, linevoltagespecifiedon thenameplatedoesnotexceed ±5%voltage

2.According tomodelsequippedwiththeappropriatedrill chuckortapersleeve, specificallyfor

theuseofthree-jawdrill chuck Φ13mm, Φ19, Φ23withNo.2Morsetapersleeve, Φ32, Φ38, Φ49,

Φ60, Φ80 use Morsetapersleeve 4#number. Inserttapershankintothe shaft.

3. Thedrill mustbesharp.Whendrill brake suddenly,youmustimmediatelyclosethedrill control

switch(Note:Donotdrilloffmagnetcontrolswitch)

4. Brushcannotbeused.Itneedstimelyexchange brush

5.Whenmagnetdrillcannotuse,itshouldimmediatelybe repaired.

6. Magnetdrill mustbekeptclean.

7. Donotimpactmagneticdrill.

8.3hourscontinuoususe, themagnetshouldrestformomentinordertopreventmagnet

overheating and burn.

Maintenance

1.Addoil frequentlyandkeepgearbox andbearing clean.

2.Maintainmagneticdrillfrequently,suchas:checkmagnetsuction,drill,powerplugs,lights,

switch,insulation, resistance whethernormal, theguide platemovementwhethernormal.

3. Saveeachpart.

4. Magnetdrill shouldbe storeduprightina dry, cleanandno corrosivegasenvironment.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

4

ⅤMalfunction Diagnosis&SolutionMethod

ⅥPartsformagneticdrill

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

5

No. NAME QTY. No. NAME QTY

1 Slewing bearing cap 1 45 Guide board 1

2 Bearing 30206 1 46 Rack 1

3 Principal axis 1 47 Pad Ф6 3

4 Square key 6x6x12 1 48 Tracking pad 1

5 Oil seal cover 1 49 Tracking pad 1 1

6 Felted wool 1 50 Tracking pad 2 1

7 Socket cap screw M6x25 3 51 Nameplate 1

8 Oil seal gasket 1 52 Hollow-head setscrew M8x15 3

9 Supporting shoe 1 53 Adjusting collar for shaft tip 1

10 Spindle collar 1 54 Socket cap screw M6x20 5

11 Elastic cylindrical pin 2 55 Hexagon die nut M6 5

12 Socket cap screw M5x55 4 56 Bush 2 1

13 Pad Ф5 16 57 Elastic cylindrical pin 3x8 4

14 Gearbox housing 1 58 Socket cap screw M8x25 4

15 Bearing 6004 1 59 Pad Ф8 4

16 Gearwheel 1 60 Staff gauge 1

17 Lockwasher 1 61 Hexagon die nut M20 1

18 Round nut M16x1.5-7 1 62 Lumplate pressure pad 1

19 Cap 1 63 Lumplate 1

20 Bearing 6001 1 64 Double screw pipe 1

21 Bearing 609 2 65 Electromagnet assembly 1

22 Gear shaft 1 66 Cruciform slot screw M5x8 1

23 Semicircular key 4x13 1 67 Cylindrical pin Ф3x20 1

24 Pinion 1 68 Turning handle 1

25 Rotor 1 69 Locknut M10x50 1

26 Ring 1 70 Steel ball Ф8 1

27 Bearing 629 1 71 Ball stud Ф8x8 1

28 Cruciform slot screw M5x65 2 72 Semicircular key 5x13 2

29 Stator 1 73 Handle lever 3

30 Inner case 1 74 Handle bush 3

31 Socket cap screw Mx14 4 75 Handle seat 1

32 Safety cover for wire holder 1 76 Handle bearing 1

33 Plastic bonding cap 2 77 Bush 1 1

34 Cruciform slot screw 4 78 Gear 1

35 Carbon brush cap 2 79 Collar Ф18 1

36 Carbon brush spring 2 80 Breadboard assembled 1

37 Carbon brush 2 81 Cable line 1

38 Carbon hold 2 82 Cable bearer 1

39 Flexible conduit 1 83 Junction box 1

40 Socket cap screw Mx25 8 84 Frame 1

41 Socket cap screw M5x15 3 85 Soft cable line 1

42 Plate for flexible conduit 2 86 Cable shroud 1

43 Cruciform slot screw M4x8 13 87 Locknut M20x1.5 1

44 Socket cap screw M6x16 3

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

6

Some experts believe the incorrect or prolonged use of almost any

product could causeserious injury or death. For information that

may reduce your risk of serious injury or death consult thepoints

below and additionally, the information available at

www.datastreamserver.com/safety

- Consult all documentation, packaging and

product labelling be fore use. Note that some

products feature online documentation which

should be printed and kept with the product.

- Check product for loose / broken / damaged /

missing parts, wear or leaks (if applicable) be fore

each use. Never use a product with loose / broken

/ damaged / missing parts, wear or leaks (if

applicable).

- Products must be inspected and serviced (if

applicable) by a qualified specialist every 6

months assuming average residential use by a

person of average weight and strength, ab ove

average technical aptitude, on a property

matching average metropolitan specification.

Intended use outside these guidelines could

indicate the product is not suitable for intended

use or may require more regular inspection or

servicing.

- Ensure all possible users of the p roduct have

completed an industry recognised training course

before being given access to the product.

- The product has been supplied by a general merchandise

retailer that may not be familiar with your specific applic ation or

your description of the application. Be sure to attain third party

approval for your application from a qualified specialist before use

regardless of prior assurances by the retailer or its representatives.

- This product is not intended for use where fail-safe operation is

required. As with any product (take an au tomobile, aircraft,

computer or ball point pen for example) there is always a small

chance of a technical issue that needs to be repaired or may

require replacement of the product or a part. If the possibility of

such failure and the associated time it takes to rectify could in any

situation inconvenience the user, business or employee or could

financially affect the user, business or employee then the product

is not suitable for your requirements. This p roduct is not for use

where incorrect operation or a failure of any kind, including but

not limited to a condition requiring product return, replacement,

service by a technician or replacement of parts could cause a

financial loss, loss of employee time or an in convenience

requiring compensation.

- If this item has been purchased in error considering the points

above simply contact the retailer directly for details of their

returns policies if required.

Baumr-AG MD1101 User manual

Popular Drill manuals by other brands