Belden RVAXCTK96CBK User manual

REVCONNECT 10GX WALL MOUNT SYSTEM
INSTALLATION GUIDE
PX106708 - EN REV A Page 1 of 8
PRODUCT DESCRIPTION HARDWARE KIT CONTENTS TOOLS REQUIRED
Termination Kits:
1. 96-ports with Couplers (inclu.100 cores)
RVAXCTK96CBK
2. 16-ports with Couplers (inclu. 16 cores)
RVAXCTM16CBK
3. 96-ports with Jacks (inclu.100 cores)
RVAXCTK96JBK
4. 16-ports with Jacks (inclu. 16 cores)
RVAXCTM16JBK
Mount and Module:
5. Mount 96 ports (empty)
RVUXCMT96E
6. Module 16-ports (empty)
RVUXCCM16E
Hook and loop cable ties of 8″ - (6x)
Wood screws #10 x 0.75″ - (2x)
▪ Philips screw driver #2
▪ Marker
▪ Tape ruler
▪Spirit level
7REVConnect Wall Cable
Dressing Module (Optional)
RVUCADM
Refer to PX106709 Installation Sheet for more information
8REVConnect Wall Cable Management
Channel (Optional)
RVUPCMC Refer to PX106710 Installation Sheet for more information
9REVConnect Horizontal Channel Kit
(Optional)
RVUHOCK Refer to PX106711 Installation Sheet for more information
1
2
3
4
5
6
7
8
9
REVCONNECT
Coupler
Modular Jack

REVCONNECT 10GX WALL MOUNT SYSTEM PX106708 - EN REV A Page 2 of 8
INSTALLATION GUIDE
REVCONNECT 10GX WALL MOUNT SYSTEM - INSTALLATION
72"
48" 48"
18" REF
8" REF 8" REF
4" REF
4" REF
14" REF
Wall
Small/Medium cross-connect systems
(Recommended)
Additional horizontal capacity for
large cross-connect systems (Optional)

REVCONNECT 10GX WALL MOUNT SYSTEM PX106708 - EN REV A Page 3 of 8
INSTALLATION GUIDE
B
3.
ATighten
partially
2.
Hold
Reference line
Reference line
48"
72"
10"
B
OK
A
1.
Reference line
Reference line

REVCONNECT 10GX WALL MOUNT SYSTEM PX106708 - EN REV A Page 4 of 8
INSTALLATION GUIDE
Reference line
Fully tighten
4.
A
5.
Reference line
B
*Alternate mounting holes (4x)
Reference line
RVUCADM installed:
Refer to PX106709 installation sheet for further
information.
8"
= Previously installed
components

REVCONNECT 10GX WALL MOUNT SYSTEM PX106708 - EN REV A Page 5 of 8
INSTALLATION GUIDE
6.
8" System Growth
Cross Connect side 2
Cross Connect side 1
= Previously installed components
6
2
1
57
3
4
8

REVCONNECT 10GX WALL MOUNT SYSTEM PX106708 - EN REV A Page 6 of 8
INSTALLATION GUIDE
REAR CABLE DRESSING.
B
1.
A
Top View
RVUCADM
RVUXCMT96E Shown
Each bundle is
composed by a
maximun of 96
cables.

REVCONNECT 10GX WALL MOUNT SYSTEM PX106708 - EN REV A Page 7 of 8
INSTALLATION GUIDE
Refer to REVCONNECT
Cores installation guide
(PX106434) for further
information.
2.
B
Support
bar
8"
Pull cables as much possible and cut them.
Starting at the bottom, separate the wide bundle into groups of 16 cable
bundles maximum (use the supplied cable ties).
A
Top cables must pass
above the support bar
Bottom cables must pass under
the support bar
Wide bundle
Bundles
composed
with a
maximum
of 16
cables

REVCONNECT 10GX Wall Mount System - Installation Guide
PX06708 - EN REV A
This document is also available at our site:
www.belden.com
For more information about BELDEN Technical support, call at:
1-800-235-3361 Page 8 of 8
3.
PATCH CABLE/CORD ROUTING
R
e
c
o
m
m
e
n
d
e
d
m
e
t
h
o
d
RVUHOCK installed:
Refer to PX106711 installation
sheet for further information.
RVUPCMC installed:
Refer to PX106710 installation
sheet for further information.
B16X
A
T
e
r
m
i
n
a
t
i
o
n
M
o
d
u
l
e
s
w
i
t
h
J
a
c
k
s
s
h
o
w
n
For the Coupler front
core installation,
Refer to REV-
CONNECT Cores
installation guide
(PX106434) for further
information.
*Use AX101532-541 LabelFlex Label Sheets
for ports identication.
When installing Modules, make sure the 16-port is in the
right orientation (L to R).