Bellini ALEXANDER 4200 User manual

Barry Imports East Corp.
Instructions for Crib Model:
165 Oval Drive, 4200
Islandia, 4400
NY 11749, USA
Page 1/14
READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB.
KEEP THE INSTRUCTIONS FOR FUTURE USE.
ALEXANDER
SYDNEY
CRIB/BED ASSEMBLY
INSTRUCTIONS
This crib has been designed for your child’s comfort and your convenience.
Quality material and workmanship have gone into this crib which will provide a
sound and comfortable bed for your baby if properly assembled and maintained.
For the security of your child be sure to follow the assembly instructions exactly.
A periodic check should be made of all bolts and screws, which should be
tightened if needed.
Moisture and heat are harmful to the finish; for this reason use extreme caution
when a vaporizer is in use. Some types of soft plastic toys that come into contact
with finish materials could also be harmful to the finish on your furniture.
This crib conforms to applicable regulations promulgated by the Consumer
Product Safety Commission.

WARNING: Failure to follow these warning and the
assembly instructions could result in serious injury or death.
Page 2/14
■ To reduce the risk of SIDS, pediatricians recommend healthy infants be placed
on their backs to sleep, unless otherwise advised by your physician.
■ Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
■ Infants can suffocate in gaps between crib sides and a mattress that is too
small.
STRANGULATION HAZARD:
◆ Strings can cause strangulation! DO NOT place items with a string around a
child’s neck, such as hood strings or pacifier cords. DO NOT suspend strings
over a crib or attach strings to toys.
◆
To help prevent strangulation tighten all fasteners. A child can trap parts of the
body or clothing on loose fasteners.
◆ DO NOT place crib near window where cords from blinds or drapes may
strangle a child.
FALL HAZARD:
* When child is able to pull to a standing position, set mattress to lowest position
and remove bumper pads, large toys and other objects that could serve as steps
for climbing out.
* Stop using crib when child begins to climb out or reaches the height of 35 in.
(89 cm).

Page 3/14
• Check this product for damaged hardware, loose joints, loose bolts or other
fasteners, missing parts, or sharp edges before and after assembly and frequently
during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if
any parts are missing, damaged or broken. Contact Barry Imports East Corp. for
replacement parts and instructional literature if needed. DO NOT substitute
parts.
• If refinishing, use a non-toxic finish specified for children’s products.
•
Never use plastic shipping bags or other plastic film as mattress covers because
they can cause suffocation.
• Do not use a water mattress with this crib.
• Follow warnings on all products in a crib.
• This crib conforms to applicable regulations promulgated by the Consumer
Product Safety Commission.
CAUTION:
Any mattress used in this crib shall be at least
27 1⁄4 inches (69cm) by 51 5⁄8 inches (131cm) with a
thickness not exceeding 6 inches (15cm).

A B C D E F
G H I J N L
K M O
ALEXANDER CRIB HARDWARE
Page 4/14
TOOLS REQUIRED
FOR ASSEMBLY:
Metric Allen Wrench( Included)
Standard Size Screwdriver
(Not included)
Quantity Quantity
A Allen head bolt 1-3/8" 4 I Cam screw 12
B Allen Wrench 1 J Self Locking washer 34
C Barrel Nut 12 K Small metal washer 8
D Big Metal Washer 18 L Allen head bolt 4" 12
E Screw (For crib drawer) 12 M Allen head bolt 1"
(For convert to bed)
4
F Allen head bolt 2" 4 N Allen head bolt 2-3/8" 2
G Wing Nut 8 O Wood plug 2
H Phillips head screw 1-3/8" 8
Alexander Crib Hardware Alexander Crib Hardware

A B C D E F
G H I J N L
K M O
SYDNEY CRIB HARDWARE
Page 5/14
TOOLS REQUIRED
FOR ASSEMBLY:
Metric Allen Wrench( Included)
Standard Size Screwdriver
(Not included)
Quantity Quantity
A Allen head bolt 1-3/8" 4 I Cam screw 12
B Allen Wrench 1 J Self Locking washer 34
C Barrel Nut 12 K Small metal washer 14
D Big Metal Washer 12 L Allen head bolt 4" 12
E Screw (For crib drawer) 12 M Allen head bolt 1"
(For convert to bed)
4
F Allen head bolt 2" 4 N Allen head bolt 2-3/4" 2
G Wing Nut 8 O Wood plug 2
H Phillips head screw 1-3/8" 8
Sydney Crib Hardware Sydney Crib Hardware

DRAWING QTY DESCRIPTION
2
Stabilizer Bars
1
Mattress Support Spring
1
Dust Cover
1
Stationary Front Rail
1
Left Crib End
1
Right Crib End
1
Headboard
2
Drawer Metal Guide
CRIB PARTS
Page 6/14
Left Crib End Right Crib End

DRAWING QTY DESCRIPTION
1
Drawer Front
1
Drawer Back
1
Left Drawer Side
1
Drawer Center
1
Right Drawer Side
2
Drawer Bottom Board
ADDITIONAL PARTS
Page 7/14

ASSEMBLY INSTRUCTIONS
Page 8/14
Diagram 1:
Unpack and familiarize yourself with all parts and
components by comparing them with the pictures
and descriptions on pages 4,5,6,7.
Mounting the drawer guides to the bottom of the
left crib end and right crib end. Using Allen wrench
B, mount the two drawer guides to the bottom of the
left crib end and right crib end with screws(A) , self
locking washer (J), and small metal washer (K) like
DIAGRAM 1/B
in the lowest holes on the inside of the
end panels.Tighten screws.
STEP 1-Drawer Glides Assembly
Diagram 2:
Attach stabilizer bars (Page 6) to the right crib
end. From the outside of the right crib end insert
screws (L) ,self locking washer (J), and big metal
washers(D) like DIAGRAM 2/A through holes
provided and into stabilizer bar. Insert barrel nut
(C) into stabilizer bar and thread screws (L) ,self
locking washer (J), and big metal washers(D) into
nuts (C). Tighten until snug with allen wrench (B).
Repeat for the left crib end.
Lie dust cover(thin masonite board) on top of dust
cover supports, on inside of the stabilizer bars.
STEP 2- Stabilizer Bars Assembly
DIAGRAM 1/B
DIAGRAM 2/A
K J A
L J D

ASSEMBLY INSTRUCTIONS
Page 9/14
Diagram 3:
To attach the mattress support spring, carefully
place the spring frame in the crib so it rests on
the stabilizer bars. Attach lower portions of the
brackets to stabilizer bar using 4 screwes(H),4
self locking washers (J), and 4 wing nuts (G) like
DIAGRAM 3/A. Tighten with a phillips screw
driver(Not included)
Note: Wing nuts should be installed with self
locking washers on inside of the stabilizer bars.
STEP 3-Matress Support Assembly
Diagram 4:
The mattress support spring has three height
positions. Use 4 screws (H), 4 self locking
washers (J), and 4 wing nuts (G) to mount
upper arm of bracket to desired height.
(DIAGRAM 3/A)
Note: Wing nuts should be installed with self
locking washers on inside of the stabilizer bars.
DIAGRAM 3/A
G J H

ASSEMBLY INSTRUCTIONS
Page 10/14
Diagram 5:
To assemble the headboard to the crib, insert the
screw N through the holes at the top of the legs
with self locking washer(J), big metal washer(D),
like DIAGRAM 5/A and screw with the allen
wrench B.
Then insert the screws L with self locking washer
(J), big metal washer(D) like DIAGRAM 5/B
through the holes at the bottom of the legs. Insert
the barrel nuts(C) in the left & right crib ends
and screw everything with the allen wrench B.
STEP 4-
Headboard Assembly
Diagram 6:
IMPORTANT:
The Stationary Front Rail must be fitted with
the reference marks facing the interior of the
crib.
DIAGRAM 6
DIAGRAM 5/A
DIAGRAM 5/B
J D N
J D L

ASSEMBLY INSTRUCTIONS
Page 11/14
Diagram 7:
Position the stationary front rail against the ends of the
crib.Insert screws F, self locking washer (J), and small
metal washer (K) like DIAGRAM 7/A
through the holes of
front rail and tighten with the allen wrench B.
STEP 5- Stationary Front Rail Assembly
DISASSEMBLE THE STATIONARY FRONT RAIL
Remove all 4 screws F from the front rail using allen
wrench B and the front rail will comes off.
STEP 6- Convert to a Full size bed
Diagram 8:
Using the headboard to build a full size bed.
Secure the mattress spring to the headboard with
screws M,
self locking washers (J), and big metal washers (D) like
DIAGRAM 8/A using four holes with bushings located at the
base of the legs.
DIAGRAM 9
MASKING THE HOLES ON THE HEADBOARD
Diagram 9:
Insert wood plugs into the holes on the headboard to cover
the holes.
DIAGRAM 7/A
DIAGRAM 8/A
J K F
J D M
DIAGRAM 7
DIAGRAM 8

DRAWER ASSEMBLY INSTRUCTIONS
Page 12/14
Diagram 10:
Screw in all 6 piece screws (E) into drawer
back panel, put 6 cam screws(I) into drawer
right side, left side,and drawer center piece.
Make sure cam screws(I) are in open position.
Diagram 11:
Attache drawer sides and drawer center to the
drawer back. Use screwdriver to turn the cam
screw(I) to lock into place. Insert two drawer
bottom boards into channels.
Dragram 12:
First screw all 6 screws (E) into drawer front,
then attach the drawer front to drawer sides
and center. Turn the barrel nuts to lock.
Diagram 13:
Slide drawer into guides on crib end panels
(wheel to wheel).

Page 13/14
CARE AND MAINTENANCE
Maintenance:
After completing the assembly process, you are advised to read and be aware of all
WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices
contained in these instructions.
Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing
parts, or sharp edges before and after assembly and frequently during use.
Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing,
damaged or broken. DO NOT substitute parts. DO NOT make any alteration to this crib.
Use care when using a vaporizer or humidifier around the crib. Do not aim the vapor at the crib
or any other wooden furniture in the nursery. Avoid using vaporizers or humidifiers for
extended periods of time.
Your crib has a durable and protective non-toxic finish. However, if you decide to refinish it,
you must use a non-toxic finish specified for children’s products. Do not use any toxic
stripping methods to remove the old finish.
Cleaning:
To clean the crib, wipe with a damp cloth and immediately dry the surface. Do not use any
chemical cleaners or polishes. Such products can leave a residue on the finish and come in
contact with your child. NO ABRASIVES, SCOURING PADS, STEEL WOOL, OR
COARSE RAGS should be used to clean this fine furniture.
Storage:
Keep instructions for future use. Store the instruction manual in the supplied envelope attached
to mattress support for future reference.Wood is natural material. As such, it can be affected by
changes in temperature and humidity. Extreme changes in humidity and temperature can cause
the wood to warp, swell, crack, or shrink, thus compromising the structural integrity of the crib
and making it dangerous to use. Do not store furniture in damp basements or hot attics. Allow
for plenty of air movement around the furniture, and do not stack it.
Do not store excess hardware in the paper pouch attached to mattress support as it could
present danger to a child if retrieved and it could also puncture the crib mattress.
Use the Page opposite to order spare parts.
Simply cut along the dotted line and give or send
the page to your nearest dealer.