GOGO KIDZ QRKIDZ User manual

®
GOGO KIDZ®
TRAVELMATE
MODEL QRKIDZ
ASSEMBLY &
ATTACHING GUIDE
7013 Realm Drive Suite C San Jose, CA 95119 / p [phone] / f [phone] / www.gogobabyz.com
Go-Go Babyz®Corporation
when you and your baby are“on the go”

B
D
E
1. Insert the Handle (A) into the Plate (C)
2. Align pre-drilled holes at the bottom
of the Handle with holes in front of
Plate (It is okay of holes do not align perfectly
they are to be used as a guide)
3. Insert Handle Screws (B) in front of Plate
4. Pull up on Handle to ensure it is secured
5. Insert Axle (D) through opening at
bottom of Plate
6. Slide Wheel with Quick Release
Spring Locks (E) on to each side of
Axle, push on Spring Lock until wheel
snaps in place
7. Test connection by pulling on
Wheels to ensure they are secured
*You will need a Philips Head Screwdriver or electric drill for Handle Screws
Front of plate
A
C
P A R T S
0201
ASSEMBLY
A. Handle (1)
B. Handle Screws (2)
C. Plate (1) with Quick Release Strap Attached
D. Axle (1)
E. Wheels (2) with Quick Release Spring Locks (2)
Ladder
Strap
Buckle /
Ratchet
Strap
E
C
Ladder
Stra
p
B
uc
kl
e
/
R
atc
h
et
Stra
p
Adjusting
Clip
Metal Brackets &
Binding Posts

B
D
E
1. Insert the Handle (A) into the Plate (C)
2. Align pre-drilled holes at the bottom
of the Handle with holes in front of
Plate (It is okay of holes do not align perfectly
they are to be used as a guide)
3. Insert Handle Screws (B) in front of Plate
4. Pull up on Handle to ensure it is secured
5. Insert Axle (D) through opening at
bottom of Plate
6. Slide Wheel with Quick Release
Spring Locks (E) on to each side of
Axle, push on Spring Lock until wheel
snaps in place
7. Test connection by pulling on
Wheels to ensure they are secured
*You will need a Philips Head Screwdriver or electric drill for Handle Screws
Front of plate
A
C
P A R T S
0201
ASSEMBLY
A. Handle (1)
B. Handle Screws (2)
C. Plate (1) with Quick Release Strap Attached
D. Axle (1)
E. Wheels (2) with Quick Release Spring Locks (2)
Ladder
Strap
Buckle /
Ratchet
Strap
E
C
Ladder
Stra
p
B
uc
kl
e
/
R
atc
h
et
Stra
p
Adjusting
Clip
Metal Brackets &
Binding Posts

IMAGES OF GOGO KIDZ STRAP
GOING THROUGH CAR SEAT.
NOTE: The Quick Release Strap is pre-assembled onto the plate of the gogo Kidz Travelmate
for use with most car seats. You may need to make adjustments in the length of the strap
or the position the strap is located on the gogo Kidz Plate. If so, please refer to page 5.
1. Place car seat face down on oor. *
2. Locate the two ribs on each side of your car seat .
3. Align the two support Tabs at the bottom of the gogo Kidz Plate with bottom of ribs
(or the bottom of base).
NOTE: Some car seats require the Tabs of the gogo Kidz Plate to go under the base -
not the car seat ribs. Do not attach to base on Britax car seats. If your car seat has a
removable base, you may need to remove the base prior to attaching the gogo Kidz
Travelmate.
4. Lay the gogo Kidz Plate at on top of the back of the car seat.
5. Take the Ladder Strap (long side of the strap - already attached to the
gogo Kidz Plate) and insert through the same opening you would put your
car seat belt in the forward facing position.
6. Insert Ladder Strap into the buckle located on opposite side of the gogo Kidz
Plate and use ratchet to tighten. Tighten securely, but DO NOT OVERTIGHTEN.
7. Pick up your car seat by the Handle of the gogo Kidz Travelmate.
8. Test connection by releasing the Handle into the upright position and
pulling /pushing your seat around the room.
9. If your car seat has a tether strap, pull 10” of strap out and pull over handle
attaching tether latch to plate handle, tighten strap.
•After the rst time you attach and are familiar with the product, you may also
attach the gogo Kidz Travelmate to a car seats while in an upright position
and with a child sitting in the car seat.
Car seat resting on Tabs of the gogo
Kidz Travelmate Plate. Ladder Strap
going through forward facting seat
belt hole.
Quick Release Strap going all the
way through opening in car seat.
Ladder Strap coming through other
side of car seat.
Ladder Strap inserted into ratchet
buckle.
PLACERAT
P L A C E R A T
0403
A T T A C H I N G T O Y O U R C A R S E A T

IMAGES OF GOGO KIDZ STRAP
GOING THROUGH CAR SEAT.
NOTE: The Quick Release Strap is pre-assembled onto the plate of the gogo Kidz Travelmate
for use with most car seats. You may need to make adjustments in the length of the strap
or the position the strap is located on the gogo Kidz Plate. If so, please refer to page 5.
1. Place car seat face down on oor. *
2. Locate the two ribs on each side of your car seat .
3. Align the two support Tabs at the bottom of the gogo Kidz Plate with bottom of ribs
(or the bottom of base).
NOTE: Some car seats require the Tabs of the gogo Kidz Plate to go under the base -
not the car seat ribs. Do not attach to base on Britax car seats. If your car seat has a
removable base, you may need to remove the base prior to attaching the gogo Kidz
Travelmate.
4. Lay the gogo Kidz Plate at on top of the back of the car seat.
5. Take the Ladder Strap (long side of the strap - already attached to the
gogo Kidz Plate) and insert through the same opening you would put your
car seat belt in the forward facing position.
6. Insert Ladder Strap into the buckle located on opposite side of the gogo Kidz
Plate and use ratchet to tighten. Tighten securely, but DO NOT OVERTIGHTEN.
7. Pick up your car seat by the Handle of the gogo Kidz Travelmate.
8. Test connection by releasing the Handle into the upright position and
pulling /pushing your seat around the room.
9. If your car seat has a tether strap, pull 10” of strap out and pull over handle
attaching tether latch to plate handle, tighten strap.
•After the rst time you attach and are familiar with the product, you may also
attach the gogo Kidz Travelmate to a car seats while in an upright position
and with a child sitting in the car seat.
Car seat resting on Tabs of the gogo
Kidz Travelmate Plate. Ladder Strap
going through forward facting seat
belt hole.
Quick Release Strap going all the
way through opening in car seat.
Ladder Strap coming through other
side of car seat.
Ladder Strap inserted into ratchet
buckle.
PLACERATP L A C E R A T
0403
A T T A C H I N G T O Y O U R C A R S E A T

Cosco Alpha Omega Series
The Alpha Omega 3-in-1 car seat has a removable base for certain situations such as
airline use. The gogo Kidz Travelmate only ts with the base removed.
Eveno Triumph
To attach to the Eveno® Triumph car seat you will use with the strap all the way
extended and the Triumph seat all the way in the reclined position.
The car seat should be adjusted to lean all the way back, otherwise; child will be too
vertical. Follow remaining instructions inside guide.
PLACERAT
P L A C E R A T
0605
QUICK RELEASE STRAP
ADJUSTMENTS
SPECIAL INSTRUCTIONS / SIDE
N O T E S O N S O M E C A R S E A T S
NOTE: The Quick Release Strap on the gogo Kidz has been assembled in the most common
position, to t most car seats. Once the gogo Kidz Travelmate has been properly attached to
a car seat, it should not move or slide around. Your car seat should easily roll freely once
tilted back on the gogo Kids Travelmate wheels. If not, please adjust either the length of the
strap for more tension or the position of the strap on the gogo Kidz Travelmate. The strap
should be level with the forward facing car seat belt opening.
Metal
Brackets
Adjusting
Clip
TO ADJUST THE TENSION: Remove gogo Kidz Travelmate from your car seat. Adjust the strap
with the adjusting clip. Reattach to your car seat and make sure when tightening the ratchet
that the ladder strap is not able to tighten all the way to the base of the ladder strap.
TO ADJUST THE STRAP HEIGHT: Remove
the metal brackets that attach the strap
to the gogo Kidz Travelmate Plate with a
screwdriver. Reposition the bracket in
holes running down the side of the gogo
Kidz Travelmate Plate.
NOTE: Make sure you position both metal brackets in
same hole (ex: left side is fourth hole from the
top and right side is fourth hole from the top.

Cosco Alpha Omega Series
The Alpha Omega 3-in-1 car seat has a removable base for certain situations such as
airline use. The gogo Kidz Travelmate only ts with the base removed.
Eveno Triumph
To attach to the Eveno® Triumph car seat you will use with the strap all the way
extended and the Triumph seat all the way in the reclined position.
The car seat should be adjusted to lean all the way back, otherwise; child will be too
vertical. Follow remaining instructions inside guide.
PLACERATP L A C E R A T
0605
QUICK RELEASE STRAP
ADJUSTMENTS
SPECIAL INSTRUCTIONS / SIDE
N O T E S O N S O M E C A R S E A T S
NOTE: The Quick Release Strap on the gogo Kidz has been assembled in the most common
position, to t most car seats. Once the gogo Kidz Travelmate has been properly attached to
a car seat, it should not move or slide around. Your car seat should easily roll freely once
tilted back on the gogo Kids Travelmate wheels. If not, please adjust either the length of the
strap for more tension or the position of the strap on the gogo Kidz Travelmate. The strap
should be level with the forward facing car seat belt opening.
Metal
Brackets
Adjusting
Clip
TO ADJUST THE TENSION: Remove gogo Kidz Travelmate from your car seat. Adjust the strap
with the adjusting clip. Retach to your car seat and make sure when tightening the ratchet
that the ladder strap is not able to tighten all the way to the base of the ladder strap.
TO ADJUST THE STRAP HEIGHT: Remove
the metal brackets that attach the strap
to the gogo Kidz Travelmate Plate with a
screwdriver. Reposition the bracket in
holes running down the side of the gogo
Kidz Travelmate Plate.
NOTE: Make sure you position both metal brackets in
same hole (ex: left side is fourth hole from the
top and right side is fourth hole from the top.

®
GOGO KIDZ®
TRAVELMATE
MODEL QRKIDZ
ASSEMBLY &
ATTACHING GUIDE
7013 Realm Drive Suite C San Jose, CA 95119 / p [phone] / f [phone] / www.gogobabyz.com
Go-Go Babyz®Corporation
when you and your baby are“on the go”