Bellini BRE133BI Installation instructions

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 Aust OR 0508123108 NZ www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
INSTALLATION & OPERATION
INSTRUCTIONS
Built-In Drawer Refrigerator
Model No.
BRE133BI FINELINE: 5104015
V.4 NOV17

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 Aust OR 0508123108 NZ www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
Thank you
Thank you for choosing Bellini Appliances.
Bellini prides itself on ‘affordable living’ making sure there is
no compromise in your favourite room … The Kitchen
All Bellini appliances carry a 3 year In Home warranty,
be sure to retain your installation and user manual and
receipt.
For all warranty and technical queries please contact
1300 373 199

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
Welcome to your new Bellini Built-In Drawer Refrigerator
Thank you for choosing your new Bellini Built-In Drawer Refrigerator.
The Bellini brand is built on a foundaon of quality combined with aordability.
The operaon of this appliance is very simple, but before your use it for the rst
me, it is important that the appliance is installed correctly and that your read and
follow the instrucons contained in this booklet.
WARNING: RISK OF ELECTRICAL SHOCK
HAZARD
This appliance must be earthed. If the power cable is damaged, it
must be replaced by the manufacturer, its service agent or similarly
qualied technician. In order to avoid a hazard ensure that the
appliance is properly earthed. If an electric shock is felt when
touching the appliance immediately stop using the appliance,
switch it o and unplug the power cord at the power source.
DISPOSAL OF OLD APPLIANCES
BE SURE TO MAKE ANY LOCKS UNUSEABLE, REMOVE ANY DOOR(S) OR
DRAWERS AND DISCARD OF THEM SEPARATELY.
WARNING-CHEMICAL HAZARD: DO NOT ALLOW CHILDREN TO PLAY
WITH AN OLD APPLIANCE. CONTACT YOUR LOCAL AUTHORITY FOR
DISPOSAL PROCEDURES.
Page 1

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
Before disposing of an old appliance, please ensure it is switched o and safe.
Unplug the appliance and break o or remove any locks in order to avoid
children becoming trapped.
Important Noce: The refrigeraon system of the appliance contains gas
and refrigerants which require specialist waste disposal. The valuable
materials in this appliance can be recycled. Contact you local waste disposal
depot for proper disposal of an old appliance, your local authority or dealer if
you need any assistance.
Please ensure the pipework of this appliance is not damaged prior to disposal.
You can contribute to environmental awareness by insisng on an appropriate
non-pollung method of disposal.
DISPOSAL OF PACKAGING
Do not allow children to play with the packaging and destroy any plasc bags
safely.
The cardboard may be broken or cut into smaller pieces and given to a paper
disposal service. The wrapping foil is made polyethylene. The polyethylene pads
stung contain no uorochlorohydrocarbons.
All of these valuable materials may be taken to a waste collecon depot
and used again aer adequate recycling. Consult your local authority for
the name and address of the waste disposal services nearest to you.
IMPORTANT SAFETY INSTRUCTIONS
Before switching on your appliance for the rst me, read the informaon
contained in this user manual carefully. The manual contains important
observaons relang to the assembly, operaon and maintenance of the
appliance.
Please keep this booklet in a safe place for future reference. If you ever resell
this appliance, hand this manual to the new owner. The manufacturer does not
accept responsibility for any damages that may arise due to non-observaon of
these instrucons. The user is liable for any material damage or bodily injury
(product liability) caused by using the appliance carelessly or failing to follow
the instrucons.
Page 2

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
Do not use damaged appliances. If you are in doubt, consult an authorised
service agent.
Connecon and installaon of the refrigerator is to be carried out in strict
compliance with the relave instrucons in this manual.
Do not damage any parts of the appliance which carry refrigerant by piercing,
perforang, crushing, twisng or scraping. If the refrigerant comes into contact
with the eyes, it may cause serious eye injury.
Always remember to unplug the appliance before cleaning. Never unplug the
appliance by pulling on the power cable. Always switch o the appliance at the
power socket, grip the plug rmly and pull the plug straight out of the socket.
Always check that the plug and cable are undamaged.
All repairs must be made by the manufacturer, its service agent or similarly
qualied service technician. Inadequate repairs may be dangerous. Never try to
repair the appliance yourself.
Should the cover of the interior light fall o or break, immediately switch o
the appliance and replace the cover.
Ensure the locaon has a at, level and stable surface. The appliance may be
levelled by turning either or both of the adjustable feet in the front corners.
Check that the appliance is level using a spirit level. Foot adjustable dimensions
minimum 16mm, maximum 24mm. Appliance dimensions
600mmWx600mmDx865mmH
Do not obstruct or cover the venlaon aperture.
Do not posion the appliance with its rear panel directly against a wall.
Maintain a gap of at least 50mm between the appliance and any adjacent wall.
Posion the appliance away from heat sources, ensure the appliance is well
venlated and protected from moisture or extremes of heat or cold.
The appliance may not funcon properly if the temperature rises above +30OC
(standard model).
Do not allow children to play with the appliance, or sit on it or to hang on to the
door(s) or drawers.
Ensure the power point is properly earthed to ground. Consult a qualied
electrician if you are unsure.
Page 3

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
This appliance is designed to operate on a power supply of 220/240 volts.
Connected to a separate power point with a correctly earthed three pin socket.
Do not use double adaptors.
Do not store explosive substances such as aerosol cans with a ammable
propellant in this appliance.
Ensure all vents are clear of obstrucon parcularly if the appliance is a built-in
model.
Do not use mechanical devices or other means to accelerate the defrosng
process, other than those recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
BEFORE USING FOR THE FIRST TIME
Do not posion the appliance with its rear panel directly against a wall.
For good circulaon and operang eciency, the venlaon grilles must never be
blocked.
Remove all packaging and place the appliance on a stable, secure at surface. Posion
the appliance away from heat sources, where the appliance is well-venlated and
protected from moisture or extremes of heat or cold.
The appliance may not funcon properly if the temperature rises above +30OC
(standard model). This appliance meets the operang condions according to the
standard EN 411-4 in climate class 4. A 10 amp fuse is ed. Never replace with a fuse
rated higher than 10A.
NEVER USE AN EXTENSION LEAD
Do not use extension cords or double adapter plugs with this appliance.
If the power cord does not reach the nearest power point, either rearrange the layout
or consult an electrician to t a new power point.
If the appliance is unplugged or the power is cut o, wait for at least 5 minutes before
plugging in and restarng the appliance to avoid damaging the compressor.
Page 4

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
Do not place combusble, explosive or volale arcles, corrosive acid or alkali liquids
in glass containers in this appliance. Always exercise cauon if adjusng the
temperature.
IMPORTANT: Allow the refrigerator to stand upright for 24
hours before plugging in for the rst me.
Page 5

Page 6
GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
OPERATION
Place the shelves or drawers rmly on their supports. Check that the appliance is
funconing properly before using it. An oponal light switch is inside the appliance.
Never place warm or hot foods directly into the appliance.
The electronic controller is located inside, it looks like this:
Page 7
Front Panel Operaon
1. Set the temperature (compressor stop temperature) adjustment
Press the buon, the set temperature is ash displayed.
Press or buon to modify ans store the displayed value.
Press buon to exit the status and display the cold room temperature.
If no more buons are pressed within 6 seconds, the cold room temperature
will be displayed.
SET
Δ
Δ
SET

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
IMPORTANT
 The appliance will go through a normal periodical defrosng cycle, and a manual
defrosng operaon is only required in most extreme cases. It is beer to avoid it
if not necessary.
 Whilst in defrost mode, the appliance cooling power is reduced, as the
compressor is not working. The automac cycles ensure the defrosng is done in
the most ecient manner and when required. It is not recommended to leave the
appliance in the manually set defrost mode for prolonged periods of me.
NOTE: It is not recommended to operate the appliance on a seng that
runs below 4oC as such a seng will cause the contents close to the
evaporator to freeze and will result in unnecessary strain on the cooling
system and undue high energy consumpon.
Page 8
NOTE: In normal operaon the controller turns the compressor o at
the set temperature and back on aer the temperature has reached
5oC. As such the reading in the electronic controller is almost a few
degrees above set-point which is perfectly OK.

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
CARING FOR THE APPLIANCE
CLEANING
1. BEFORE CLEANING turn the appliance o at the power point and unplug the
cord to prevent any chance of electrocuon and remove all contents.
2. Wash the inner compartment with warm soapy water, use a neutral detergent.
DO NOT allow the control panel, cables or plug to get wet. DO NOT use metal
or sharp objects to remove debris.
3. Aer cleaning dry all surfaces thoroughly.
4. To ensure trouble-free operaon the condenser should be cleaned every three
months where appropriate using a vacuum hose. The condenser is located
behind the lower grill of the cabinet. In exceponally dusty locaons the
condenser should be cleaned more oen.
5. Use mild soapy water to clean the gasket and seals.
REPLACING THE LAMP
1. Switch off the power at the power point and remove the cord by pulling the
plug.
2. Unscrew and remove the screws on both ends of the light cover, take down the
lamp cover, pull out the wires then remove the bulb.
3. Install the new bulb, connect the wires, replace the lamp cover and refit the
screws.
4. Wait for at least 5 minutes before plugging in and restarting the appliance to
avoid damaging the compressor.
WARNING: Never insert your nger into the light bulb socket.
Page 9

TROUBLSHOOTING
You can solve many common problems easily , saving you the cost of a service call.
Try the suggesons below to see if you can solve the problem before calling the ser-
vice centre.
PROBLEM POSSIBLE CAUSE SOLUTION
Appliance does not
operate.
Appliance is not connected to a power
supply.
The appliance is turned off.
Tripped circuit breaker or a blown
fuse.
Connect the appliance to a power supply.
Switch on the appliance.
Switch on the circuit breaker or replace the fuse.
Appliance is not cold
enough.
The temperature is not set correctly.
The ambient temperature could re-
quire a lower temperature setting.
The door was opened too often.
The door was not closed completely.
The door is not hermetically sealed.
The condenser is too dirty.
The ventilation opening is blocked or
too dirty.
Check the set temperature.
Set a lower temperature.
Do not open the door more often than necessary.
Close the door properly.
Check the door seal and clean or replace.
Clean the condenser when necessary.
Clear the obstructions and clean the dust.
Appliance turns itself
on and off frequently.
The room temperature is higher than
average.
A large amount of food has been add-
ed to the unit.
The door is open too often.
The door is not closed properly.
The door gasket does not seal proper-
ly.
Move the appliance to a cooler place.
Leave the appliance to work for a while unl the set
temperature has been reached.
Do not open the door more oen than necessary.
Close the door properly.
Check the door seal and clean or replace.
The light does not
work.
Appliance is not connected to a power
supply.
Tripped circuit breaker or a blown
fuse.
The light was switched off on the con-
trol panel.
Connect the appliance to a power supply.
Switch on the circuit breaker or replace the fuse.
Switch the light on at the control panel.
Vibrations The appliance is not properly levelled. Level the appliance with the adjustable feet.
The appliance seems
to make too much
noise.
The rattling noise may come from the flow of refrigerant, which is normal. As each cycle ends
you may hear gargling sounds caused by the flow of refrigerant in the appliance.
If temperature fluctuations occur, the concentration and expansion of the inner walls may
cause a popping or cracking noise.
The appliance is not properly lev-
elled. Level the appliance with the adjustable feet.
Page 10
GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
WARRANTY
1.1 In this warranty:
1.1.1 Australian Consumer Law means the law as set out in schedule 2 of the Compeon and
Consumer Act 2010.
1.1.2 Company means GSM Sales Pty Ltd ABN 53 007 682 475 of 142-144 Fullarton Road, Rose
Park SA 5067. Email [e-mail]; Australia 1300 373 199 or New Zealand 0508 123
108
1.1.3 Consumer means a ‘consumer’ as that term is dened in Secon 3 of the Australian
Consumer Law;
1.1.4 Consumer Guarantees means the guarantees under the Australian Consumer Law;
1.1.5 You means the Consumer.
1.2 Nothing in this warranty aects any person’s rights under the Australian Consumer Law. The
benets to any Consumer under this warranty are in addion to the rights and remedies
available under any Consumer Guarantees.
1.3 Subject to the other clauses of this warranty, the Company warrants to the Consumer that the
Bellini product will be free of manufacturing defects and will perform to the Company’s
specicaons.
1.4 The benet of this warranty extends only to the Consumer as the original purchaser of a Bellini
product which is installed in a residenal property.
1.5 This warranty commences on the date of purchase of the Bellini product by the Consumer and
connues for the benet only of the Consumer unl the expiry of three (3) years (Warranty Period).
1.6 If within the Warranty Period a manufacturing defect is discovered in the Bellini product or it
fails to perform to the company’s specicaons as a result of some defect in materials,
components or workmanship (Defect) then the Company will, at its opon, repair the Bellini
product or supply a replacement Bellini Product free of charge. A replacement Bellini product
may dier from the original product purchased by the Consumer.
1.7 This warrant will not apply to any Bellini product:
1.7.1 Installed by any person other than a qualied tradesperson; or
1.7.2 Subjected to misuse, neglect, negligence or accidental damage; or
1.7.3 Operated in any way contrary to any operang of maintenance instrucons; or
1.7.4 improperly handled, installed or maintained; or
1.7.5 Altered or modied prior to or aer installaon; or
1.7.6 Damaged directly or indirectly by power surges, electrical storm damage or connecon
to incorrect power supply.
Page 11

GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
The Australian Consumer Law requires the inclusion of the following statement with this warranty:
Our goods come with a guarantee that cannot be excluded under the Australian Consumer Law. You are
entled to a replacement or refund for a major failure and for compensaon for any other reasonably
foreseeable loss or damage. You are also entled to have the Appliance repaired or replaced if the Appliance
fails to be of acceptable quality and the failure does not amount to a major failure.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY
THE CONSUMER MUST CALL 1300 373 199 (AUSTRALIA) OR 0508 123 108 (NEW ZEALAND)
TO CONNECT TO THE NEAREST AUTHORISED CENTRE
1.8 You must provide proof of your purchase of the Bellini product and the date of purchase in order to obtain
the benet of this warranty.
1.9 If you live outside the service area of the Company or one of its service agents, this warranty does not
cover the cost of transport of the Bellini product for service nor the service agent’s traveling costs to and from
your home.
1.10 If you are required to transport the Bellini product to the Company or its service agent, you must ensure it is
safely disconnected by a qualied tradesman and securely packed and insured. The Company does not accept any
responsibility for loss or damage of the Bellini product prior to it being received by the Company or its service
agent.
1.11 You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of the Bellini
product by the Company (whether it is the original or a repaired and/or a replacement Bellini product and for any
other expenses you incur in claiming under this warranty.
1.12 The Company or its service agent will examine any Bellini product and if the Company determines that it is
defecve through no fault of the Owner and is otherwise undamaged, the Company will repair or replace the
Bellini product in accordance with this warranty.
DO NOT SEND IN THIS WARRANTY
Fill out the following details and le with your purchase invoice.
RETAIN & FILE WITH YOUR RECEIPT
Your Purchase Receipt/Invoice is proof of date of purchase. If you are unable to establish the date of purchase, or
if the fault is not covered by this warranty, or if the product is found to be in working order, you will be required
to bear all service call charges.
GSM Sales Pty Ltd reserves the right to disconnue items, modify designs and change specicaons without
incurring obligaon.
Whilst every eort is made to ensure that descripons, specicaons and other informaon in this publicaon is
correct, no warranty is given in respect thereof and the company shall not be liable for any errors therein.
Purchased from:
Co. Name:
Address:
Date of Purchase:
Serial number:
Page 12

NOTE: Consistent with our connuing product development policy, improvements may have
been made which render the contents of this packaging slightly dierent to that shown.
FOR WARRANTY SERVICE CALL 1300 373 199 (AUSTRALIA) OR 0508 123 108 (NEW ZEALAND) TO
CONNECT YOU TO THE NEAREST AUTHORISED SERVICE CENTRE
To ensure safe operaon, please read this instrucon manual thoroughly before use.
GSM Sales Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 www.belliniappliances.com.au
Model: BRE133BI Fineline: 5104015 Built-In Drawer Refrigerator
Page 13