Bellini BBF118BI Installation instructions

INSTALLATION & OPERATION
INSTRUCTIONS
Built-In Bar Refrigerator
Model No.
BBF118BI FINELINE: 5104016
V.6 APR18
GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 Aus Or0800 764 912 NZwww.belliniappliances.com.au
Model: BBF118BI Fineline: 5104016 Built-In Bar Refrigerator

GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 Aus Or0800 764 912 NZwww.belliniappliances.com.au
Model: BBF118BI Fineline: 5104016 Built-In Bar Refrigerator
Thank you
for
purchasing
Bellini Bar Fridge, the appliance carries a
2 year replacement warranty, be sure to
retain this Instruction Manual and
receipt.
For Technical, queries please contact
Aust: 1300 373 199
NZ: 0800 764 912

Welcome to your new Bellini Built-In Bar Refrigerator
Thank you for choosing your new Bellini Built-In Bar Refrigerator.
The Bellini brand is built on a foundaon of quality combined with aordability.
The operaon of this appliance is very simple, but before your use it for the rst
me, it is important that the appliance is installed correctly and that your read and
follow the instrucons contained in this booklet.
DISPOSAL OF OLD APPLIANCES
BE SURE TO MAKE ANY LOCKS UNUSEABLE, REMOVE ANY DOOR(S) AND DISCARD
OF THEM SEPARATELY.
WARNING-CHEMICAL HAZARD: DO NOT ALLOW CHILDREN TO PLAY WITH AN OLD
APPLIANCE. CONTACT YOUR LOCAL AUTHORITY FOR DISPOSAL PROCEDURES.
Before disposing of an old appliance, please ensure it is switched o and safe.
Unplug the appliance and break o or remove any locks in order to avoid children
becoming trapped.
Important Noce: The refrigeraon system of the appliance contains gas and
refrigerants which require specialist waste disposal. The valuable materials in
this appliance can be recycled. Contact you local waste disposal depot for
proper disposal of an old appliance, your local authority or dealer if you need
any assistance.
Please ensure the pipework of this appliance is not damaged prior to disposal. You
can contribute to environmental awareness by insisng on an appropriate
non-pollung method of disposal.
Page 1
WARNING: RISK OF ELECTRICAL SHOCK
HAZARD
This appliance must be earthed. If the power cable is damaged,
it must be replaced by the manufacturer, its service agent or
similarly qualied technician. In order to avoid a hazard ensure
that the appliance is properly earthed. If an electric shock is felt
when touching the appliance immediately stop using the
appliance, switch it o and unplug the power cord at the power
source.

DISPOSAL OF PACKAGING
Do not allow children to play with the packaging and destroy any plasc
bags safely.
The cardboard may be broken or cut into smaller pieces and given to a
paper disposal service. The wrapping foil is made polyethylene. The
polyethylene pads stung contain no uorochlorohydrocarbons.
All of these valuable materials may be taken to a waste collecon depot and
used again aer adequate recycling. Consult your local authority for the
name and address of the waste disposal services nearest to you.
IMPORTANT SAFETY INSTRUCTIONS
Before switching on your appliance for the rst me, read the informaon
contained in this user manual carefully. The manual contains important
observaons relang to the assembly, operaon and maintenance of the
appliance.
Please keep this booklet in a safe place for future reference. If you ever
resell this appliance, hand this manual to the new owner. The manufacturer
does not accept responsibility for any damages that may arise due to
non-observaon of these instrucons. The user is liable for any material
damage or bodily injury (product liability) caused by using the appliance
carelessly or failing to follow the instrucons.
Do not use damaged appliances. If you are in doubt, consult an
authorised service agent.
Connecon and installaon of the refrigerator is to be carried out in
strict compliance with the relave instrucons in this manual.
Do not damage any parts of the appliance which carry refrigerant by
piercing, perforang, crushing, twisng or scraping. If the refrigerant
comes into contact with the eyes, it may cause serious eye injury.
Page 2

Always remember to unplug the appliance before cleaning. Never unplug the
appliance by pulling on the power cable. Always switch o the appliance at the
power socket, grip the plug rmly and pull the plug straight out of the socket.
Always check that the plug and cable are undamaged.
All repairs must be made by the manufacturer, its service agent or similarly
qualied service technician. Inadequate repairs may be dangerous. Never try to
repair the appliance yourself.
Should the cover of the interior light fall o or break, immediately switch o
the appliance and replace the cover.
Ensure the locaon has a at, level and stable surface. The appliance may be
levelled by turning either or both of the adjustable feet in the front corners.
Check that the appliance is level using a spirit level. Foot adjustable dimensions
minimum 16mm, maximum 24mm. Appliance dimensions
600mmWx600mmDx865mmH
Do not obstruct or cover the venlaon aperture.
Do not posion the appliance with its rear panel directly against a wall.
Maintain a gap of at least 50mm between the appliance and any adjacent wall.
Posion the appliance away from heat sources, ensure the appliance is well
venlated and protected from moisture or extremes of heat or cold.
The appliance may not funcon properly if the temperature rises above +30OC
(standard model).
Do not allow children to play with the appliance, or sit on it or to hang on to the
door(s).
Ensure the power point is properly earthed to ground. Consult a qualied
electrician if you are unsure.
Page 3

This appliance is designed to operate on a power supply of 220/240 volts.
Connected to a separate power point with a correctly earthed three pin socket.
Do not use double adaptors.
Do not store explosive substances such as aerosol cans with a ammable
propellant in this appliance.
Ensure all vents are clear of obstrucon parcularly if the appliance is a built-in
model.
Do not use mechanical devices or other means to accelerate the defrosng
process, other than those recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
BEFORE USING FOR THE FIRST TIME
Do not posion the appliance with its rear panel directly against a wall.
For good circulaon and operang eciency, the venlaon grilles must never be
blocked.
Remove all packaging and place the appliance on a stable, secure at surface. Posion
the appliance away from heat sources, where the appliance is well-venlated and
protected from moisture or extremes of heat or cold.
The appliance may not funcon properly if the temperature rises above +30OC
(standard model). This appliance meets the operang condions according to the
standard EN 411-4 in climate class 4. A 10 amp fuse is ed. Never replace with a fuse
rated higher than 10A.
NEVER USE AN EXTENSION LEAD
Do not use extension cords or double adapter plugs with this appliance.
If the power cord does not reach the nearest power point, either rearrange the layout
or consult an electrician to t a new power point.
If the appliance is unplugged or the power is cut o, wait for at least 5 minutes before
plugging in and restarng the appliance to avoid damaging the compressor.
Page 4

Do not place combusble, explosive or volale arcles, corrosive acid or alkali
liquids in glass containers in this appliance. Always exercise cauon if adjusng the
temperature.
OPERATION
Place the shelves rmly on their supports. Check that the appliance is funconing
properly before using it. An oponal light switch is inside the appliance.
Never place warm or hot foods directly into the appliance.
ELECTRONIC THERMOSTAT
During normal operaon the controller display
will show the temperature inside the appliance.
A small indicator light will illuminate under the
‘Cooling’ symbol to conrm the appliance is in its normal cooling mode
and that the compressor is running.
When the temperature is reached and the compressor is in its ‘o’ cycle, no
indicator light will illuminate in the controller:
Operaon of the controller:
To set the desired temperature of the appliance:
Press the buon once. A ‘beep’ will sound and the display will start to
ash.
Use the buons to set the desired temperature.
Press again to complete the operaon or just leave it for 5-10 seconds
and the display will revert back to showing the internal temperature.
Note: The appliance is built to automacally defrost and prevent any ice
forming on the Evaporator. When in a ‘Defrost’ cycle, the indicator light will
illuminate under the ‘Defrost’ symbol:
Page 5
IMPORTANT: Allow the refrigerator to stand upright for 24
hours before plugging in for the rst me.

To manually acvate ‘Defrost’ cycle:
Press the buon and hold it for 6 seconds or unl a beep can be heard.
The indicator light will now illuminate under the ‘Defrost’ symbol and the fridge
is in ‘Defrost’ cycle.
‘Defrost’ will run for 20 minutes and then automacally revert to normal opera-
on.
To manually change back to normal operang mode from the ‘Defrost’ mode:
Press the buon again and hold it for 6 seconds or unl a beep can be
heard.
Both indicator lights under the ‘Defrost’ symbol and under the ‘Cooling’
symbol will now ash while the appliance is gearing up to switch back to normal
operaon.
Aer 5-20 minutes, only the indicator light will illuminate under the ‘Cooling’
symbol to indicate that the appliance is now back in normal
cooling mode.
IMPORTANT
The appliance will go through a normal periodical defrosng cycle and a manual
defrosng operaon is only required in most extreme cases. It is beer to avoid if
not necessary.
While in the ‘Defrost’ mode the appliance cooling power is reduced as the
compressor is not working. The automac cycles ensure the defrosng is done in
the most ecient manner and when required. It is not recommended to leave
the appliance in the manually set defrost mode prolonged periods of me.
NOTE: It is not recommended to operate the appliance on a seng that
runs below 4oC as such a seng will cause the contents close to the
evaporator to freeze and will result in unnecessary strain on the cooling
system and undue high energy consumpon.
NOTE: In normal operaon the controller turns the compressor o at the
set temperature and back on again aer the temperature has risen to
around 5OC.As such the reading in the electronic controller is almost a
few degrees above set-point which is perfectly OK.
Page 6

CARING FOR THE APPLIANCE
DEFROSTING
Ice may build up on the evaporator if the unit is put to work constantly for a period
of me. When ice begins to build up to approximately 4mm thick, defrosng is
required. Empty the cabinet of its contents, switch the thermostat to 'OFF' posion.
The ice will start to melt. When the ice has melted and drained away, dry o any
residual moisture with a so cloth. Switch on the power again via thermostat. Please
note it will take around 12 hours for the cabinet to get back down to temperature
with the products.
CLEANING
1. BEFORE CLEANING turn the appliance o at the power point and unplug the
cord to prevent any chance of electrocuon and remove all contents.
2. Wash the inner compartment with warm soapy water, use a neutral detergent.
DO NOT allow the control panel, cables or plug to get wet. DO NOT use metal
or sharp objects to remove debris.
3. Aer cleaning dry all surfaces thoroughly.
4. to ensure trouble-free operaon the condenser should be cleaned every three
months where appropriate using a vacuum hose. The condenser is located
behind the lower grill of the cabinet. In exceponally dusty locaons the
condenser should be cleaned more oen.
5. Use mild soapy water to clean the gasket and seals.
REPLACING THE LAMP
1. Switch o the power at the power point and remove the cord by pulling the plug.
2. Unscrew and remove the screws on both ends of the light cover, take down the
lamp cover, pull out the wires then remove the bulb.
3. Install the new bulb, connect the wires, replace the lamp cover and ret the
screws.
4. Wait for at least 5 minutes before plugging in and restarng the appliance to
avoid damaging the compressor.
WARNING: Never insert your nger into the light bulb socket.
Page 7

TROUBLSHOOTING
You can solve many common problems easily saving you the cost of a service call. Try the
suggesons below to see if you can solve the problem before calling the service centre.
PROBLEM POSSIBLE CAUSE SOLUTION
Appliance does not
operate.
Appliance is not connected to a power sup-
ply.
The appliance is turned off.
Tripped circuit breaker or a blown fuse.
Connect the appliance to a power supply.
Switch on the appliance.
Switch on the circuit breaker or replace the fuse.
Appliance is not cold
enough.
The temperature is not set correctly.
The ambient temperature could require a
lower temperature setting.
The door was opened too often.
The door was not closed completely.
The door is not hermetically sealed.
The condenser is too dirty.
The ventilation opening is blocked or too
dirty.
Check the set temperature.
Set a lower temperature.
Do not open the door more often than necessary.
Close the door properly.
Check the door seal and clean or replace.
Clean the condenser when necessary.
Clear the obstructions and clean the dust.
Appliance turns itself
on and off frequently.
The room temperature is higher than aver-
age.
A large amount of food has been added to
the unit.
The door is open too often.
The door is not closed properly.
The door gasket does not seal properly.
Move the appliance to a cooler place.
Leave the appliance to work for a while unl the set
temperature has been reached.
Do not open the door more oen than necessary.
Close the door properly.
Check the door seal and clean or replace.
The light does not
work.
Appliance is not connected to a power sup-
ply.
Tripped circuit breaker or a blown fuse.
The light was switched off on the control
panel.
Connect the appliance to a power supply.
Switch on the circuit breaker or replace the fuse.
Switch the light on at the control panel.
Vibrations The appliance is not properly levelled. Level the appliance with the adjustable feet.
The appliance seems
to make too much
noise.
The rattling noise may come from the flow of refrigerant, which is normal. As each cycle ends you
may hear gargling sounds caused by the flow of refrigerant in the appliance.
If temperature fluctuations occur, the concentration and expansion of the inner walls may cause
a popping or cracking noise.
The appliance is not properly levelled. Level the appliance with the adjustable feet.
Page 8

WARRANTY
1.1 In this warranty:
1.1.1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition and
Consumer Act2010;
1.1.2 Company means GSM Sales Pty Ltd ABN 53 007 682 475 of 142-144 Fullarton Road, Rose
Park SA 5067. Telephone [phone]. Email [e-mail];
1.1.3 Consumer means a “consumer” as that term is defined in Section 3 of the Australian Consumer
Law as the original purchaser of a Belliniproduct;
1.1.4 Consumer Guarantees means the guarantees under the Australian ConsumerLaw;
1.1.5 You means the Consumer.
1.2 Nothing in this warranty affects any person’s rights under the Australian Consumer Law. The benefits to
any Consumer under this warranty are in addition to the rights and remedies available under any
Consumer Guarantees.
1.3 Subject to the other clauses of this warranty, the Company warrants to the Consumer that the Bellini
product will be free of manufacturing defects and will perform to the Company’s specifications.
1.4 The benefit of this warranty extends only to the Consumer as original purchaser of a Bellini product which
is installed in a domestic household area.
*The in Home warranty does not apply to Commercial and or industrial usage. *Please See 1.7.7 for additional
information
1.5 This warranty commences on the date of purchase of the Bellini product by the Consumer and
continues for the benefit only of the Consumer until the expiry of three (3) year (Warranty Period).
1.6 If within theWarrantyPeriod a manufacturing defect is discovered in the Bellini product or it fails to perform
to the Company’s specifications as a result of some defect in materials, components or workmanship
(Defect) then the Company will, at its option, repair the Bellini product or supply a replacement Bellini
product free of charge. A replacement Bellini product maydiffer from the original product purchased bythe
Consumer.
1.7 This warranty will not apply to any Bellini product:
1.7.1 Installed by any person other than a qualified tradesperson;or
1.7.2 Subjected to misuse, neglect, negligence or accidental damage;or
1.7.3 Operated in any way contrary to any operating or maintenance instructions;or
1.7.4 Improperly handled, installed or maintained;or
1.7.5 Altered or modified prior to or after installation; or
1.7.6 Damaged directly or indirectly bypower surges, electrical storm damage or connection to incorrect
power supply
1.7.7 Industrial and or Commercial usage is inclusive of staff areas in office/ shop environments, hotel/
motel or other similar accommodation or rental type properties including Bed and Breakfast
establishments.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY THE CONSUMER
MUST CALL 1300 373 199 (AUSTRALIA) OR0800 764 912
(NEW ZEALAND) TOCONNECT TOTHE NEAREST AUTHORISED CENTRE
The Australian Consumer Law requires the inclusion of the following
statement with this warranty:
Our goods come with guaranteed that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.

1.8 You must provide proof of your purchase of the Bellini product and the date of purchase in order toobtain
the benefit of thiswarranty.
1.9 If you live outside the service area of the Company or one of its service agents, this warranty does not
cover the cost of transport of the Bellini product for service nor the service agent’s traveling costs to and
from your home.
1.10 If you are required to transport the Bellini product to the Company or its service agent, you must ensure it is
safely disconnected by a qualified tradesman and securely packed and insured. The Company does not
accept anyresponsibility for loss or damage of the Bellini product prior to it being received bythe Company or
its serviceagent.
1.11 You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of the
Bellini product by the Company (whether it is the original or a repaired and/or a replacement Bellini product)
and for any other expenses you incur in claiming under this warranty.
1.12 The Company or its service agent will examine any Bellini product and if the Company determines that it is
defective through no fault of the Owner and is otherwise undamaged, the Company will repair or replace the
Bellini product in accordance with thiswarranty.
DO NOT SEND IN THIS WARRANTY
Fill out the following details and file with your purchase invoice.
RETAIN & FILE WITH YOUR RECEIPT
Your Purchase Receipt/Invoice is proof of date of purchase. If you are unable to establish the date of purchase, or if
the fault is not covered by this warranty, or if the product is found to be in working order, you will be required to bear
all service call charges.
GSM Sales Pty Ltd reserves the right to discontinue items, modify designs and change specifications without
incurring obligation.
Whilst every effort is made to ensure that descriptions, specifications and other information in this publication is
correct, no warranty is given in respect thereof and the company shall not be liable for any errors therein.
Purchased from:
Co. Name:
Address:
Date of Purchase:
Serial number:
NOTE: Consistent with our continuing product development policy, improvements may have been made
which render the contents of this packaging slightly different to that shown.
FOR WARRANTY SERVICE CALL 1300 373 199 (AUSTRALIA)
OR 0800 764 912 (NEW ZEALAND) TOCONNECT YOU TO THE NEAREST
AUTHORISED SERVICE CENTRE